Statistics

298,475 members
182,081 posts

Discover

  • New
    ddxrty23
    Newcomer - Level 1
    2022-09-24
    Behringer XENYX 302USB x Beyerdynamic MMX 300 Headset microphone sound issue (HE... | USB Audio Interfaces

    Hi, So I just recently got the behringer xenyx 302usb audio interface. For me, it is everything I could have asked for...

    I use it for competitive gaming with my beydynamic MMX 300(2nd generation) gaming headset.

    I have the 5VDC power cable plugged into my gaming PC vis USB. Then I have the headset cable going from the headset into the behringer interface split from the headset to the "Headset" microphone and headphones ports.

    On my end, everything sound great and performs great. However, when I get into Discord and start talking to my teammates - They tell me that I sound very close to the microphone and they can't really understand what I am saying most of the time because it's very "muffled".

    I have ALL volume knobs set to midway. The only button that I have pressed in, is the "LINE/USB PLAY - "FROM" button pressed in.

    I checked all drivers and it says that they are all up to date via the audio interface and the headset. All Windows 11 drivers are up to date. All motherboard drivers are up to date. I am not sure what is going on here, so any help would be greatly appreciated!!

    read more...
    0 0
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    snick
    Newcomer - Level 1
    2022-09-24
    X32 V4.06 OSC over SYSEX not working | AV Professionals
    I'm having trouble sending OSC strings in MIDI SySex to the X32.
    I have set the OSC over SYSEX in the Remote Settings page, selected the card interface (X-LIVE) USB connection and am sending the string which was made using the SysexOSCGen software to send the correct string to start the recording for the X-Live.
     
    I have confirmed that the X32 is getting MIDI (I can mute/unmute channels)
     
    I have confirmed the OSC string is correct as I can send it via TouchOSC and the session will start/stop recording
     
    But when sent as MIDI SYSEX string over USB it just wont respond.
    The string I am sending is: (as output by SysexOSCGen)
     
    OSC: /-stat/urec/state 3
    F0 00 20 32 32 2F 2D 73 74 61 74 2F 75 72 65 63 2F 73 74 61 74 65 20 33 F7
     
    ​Using Bome's MIDI translator to send directly to the X-LIVE MIDI USB port with RAW MIDI
     
    Any clues?
    ​
    read more...
    0 1
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    Musikart
    Newcomer - Level 1
    2022-09-24
    TC M6000 | Multi-Effects Processors

    Hi !!

    My TC M6000 gives me an DSP AES CARD Sync Error !

    What can I do ???

     

    Thanks !

     

    Mikel 

    0 0
    0
    Mark As Solved 0 Reopen Discussion 0
    • 1 Replies
      Oldest
    • Musikart
      PedroRodrigues Hi Musikart, thank you for your post, please ponder that Sync Error (Red) points out for the Input being or has been out of Sync with the Mainframe.

      Please Press the Reset key to see if Sample Slips are still occurring.

      If that is the case, please check that there is only one Master Clock source in your setup.

      This monitoring function is great when trying to determine which connected device is out of Sync.

      In the case that the guidance above does not resolve the issue reported, please follow the link below to submit a case directly to our Tech Support Team.


      https://community.musictribe.com/pages/create-new-ticket?type=Technical%20Support&brand=TCElectronic


      I will be gladly pick up this ticket if you adress the submitted ticket to myself by stating my name of the description.

      I hope this helps


      Thank you
      • 5 hours ago
  • New
    kylesalone
    Newcomer - Level 1
    2022-09-24
    Can I use a powered sub with a powered mixer? | Power Amplifiers

    I have a Mackie powered mixer and have two passive mains and two passive monitors. 
    I have a behringer powered sub. Can I hook it up somehow? If so how?

    0 7
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    AundreMartinesz
    Newcomer - Level 1
    2022-09-24
    Behringer XAIR18 Driver Issue | Software

    HI the current dreiver does only lets me have recorning access to 8 channels and not the full 16. Could someone please advise how i could have acces to the correct driver? As I want to be able to record all 16 channels individualy.  

    0 0
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    Lawdog0716
    Newcomer - Level 1
    2022-09-23
    Setting up the compressor for an acoustic guitar on Voicelive 3 extreme | Guitar and Bass

    Hello everyone, I need some help.  I have no idea how to use the compressor for guitar on Voicelive 3 extreme.  I'm messed with it but can't figure it out.  Can someone give me some pointers?

    0 0
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    rbaza1
    Newcomer - Level 1
    2022-09-23
    UMC 1820 | USB Audio Interfaces

    I was excited when my upgrade audio interface arrived, only to have issues with driver update which I managed to get on board without any errors but now I got no audio/signal from the 1820 Main Out. I got sound from the headphone ports but none on the main out. Did I get a lemon? hate to send it back

    read more...
    0 0
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    DavidStewart
    Contributor - Level 2
    2022-09-23
    Starting VL3X backing tracks from Helix footswitches | Guitar and Bass
    I want to use Helix footswitches to start/stop/rewind backing tracks/performances on the VL3X. MIDI and MIDI machine control cannot do it. While MIDI commands can be sent from external devices to change VL3X presets (and settings of effects), there is no MIDI implementation on VL3X for transport control (a very strange exclusion). I figured out how to do it, just by poking around.  Here is what I was able to do (so far) and how:
     
    The hardware: VL3X, Helix floor, and a TRS cable (like the stereo cable you get with TC-Helicon's Step 6 and Step 3, e.g.). Don't connect the two machines with the cable until you've set both machines up with your desired settings.
     
    On the VL3X, press the Setup key on the top panel. Key over with the Right arrow > under the selection wheel, to get to the FOOTSWITCH tab in Setup. Scroll down to the Footswitch Jack setting, and select Switch-3. Go down one more row, and set the three footswitches to the functions you want. I set them to: TRACK START, TRACK STOP, and TRACK BACK (1, 2, and 3).
    On the Helix, select the Preset in which you want to control the VL3X. Press the hamburger button (the deep menu, three horizontal lines stacked), then the button/knob under Command Center. Use the joystick knob to select the footswitch you want to set first. Turn the knob under Command to select Ext Amp. For Select, choose 1 (Tip). (1 (Tip) will act as FOOTSW-1 on the VL3X. 2 (Ring) will act as FOOTSW-2. 1 and 2 will act as FOOTSW-3.) The Type is Latching as default. In order to have the bright LED, press the switch you're setting up. Now, set the Type to Momentary. (The VL3X requires momentary switches, which is what the switches on the Step-3 and Step-6 are.) Now press the knob under Customize, and give a name to the function the switch will execute. Save it, and save the preset so you don't lose your work. Now do the same with the two other Helix footswitches you want to drive the VL3X with.
     
    I did 3 switches, using Helix 8, 9, and 10. 8: 1 (Tip), Momentary, green, "Start/Pause Trac"; 9: 2 (Ring), Momentary, red, "Stop/to 0:00"; 10: 1 and 2, Momentary, turquoise, "Rewind Track".
     
    Plug the TRS cable into the EXT AMP jack on the Helix, and the Footswitch jack on the VL3X. Now you can test the switches and make sure they operate as you want.
     
    A caveat: If you connect the machines while setting them up, and you keep pressing the switches on the Helix, eventually the VL3X track player will go haywire. I don't know why; I suspect the electrical signal the VL3X receives from the Helix isn't exactly what it's built to use, and somehow it gets too much... I'll just stop there, because I don't really know what's going on or maybe even what I'm talking about with respect to this. But it went haywire on me.
     
    An additional possibility: I think the VL3X might also be operable with the footswitch set to Step-6, and with three additional footswitches on the Helix set to Latching (1 (Tip) with Latching, etc.). I haven't yet cleanly tested that kind of setup.
    My purpose was to be able to command the VL3X to run backing tracks (or loops) from the Helix pedals. It works (so far). You can use it to do other things.
    read more...
    0 6
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    Zehnder
    Newcomer - Level 1
    2022-09-23
    No Internet connection with Voice Support 2 | Software

    I am still unable to install Voice Support 2 on my laptop, even after the 'fix' that came out recently.  No internet connection error.  I have a new play acoustic.  Are there settings on either my laptop or play acoustic that may need to be changed?  I have no issues with my internet, have tried connecting using both Windows 10 and 11 laptops, and 3 different cables.  I don't know what to do at this point.

    read more...
    0 0
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    MaxThaTank
    Newcomer - Level 1
    2022-09-23
    Potential Bug Report/Question - Matrices on DCA | Digital Mixers

    Hello!

     

    Not sure if this is the place to report a bug (or find out if I am missing something), but it looks like there is something wrong with DCA assignments as far as Matrices go. I have been setting Matrices 1&2 (Linked), and 3 to DCA 8. Works great. The issue is, when you switch scenes to another scene that does not have these Matrices assigned to the DCA 8, the assignment persists until you disable it manually. No parameter/scene safes are involved, and this happens both on the Edit app and the M32 board itself.

    read more...
    0 1
    0
    Mark As Solved 0 Reopen Discussion 0
Go to page