Statistics

254,458 members
132,145 posts
  • Ratnaguna
    Contributor - Level 1
    2019-11-20

    I'm trying to set up my new equalizer but have discovered that the RCA inputs are a little too wide for the plugs! Which means that the plugs slip out of the inputs. Should I return it, or is there a remedy?

    0 162
    • Ratnaguna
      KenMitchell

      Hi Gary ( @Ratnaguna ), 


       


      Welcome to the community. This is usually caused by a worn out cable not the input jacks themselves.  Can you take a picture of the plugs and jacks so we can have a look? 


       


      Ken

      • November 21, 2019
    • Ratnaguna
      clif

      When this happens to me , I take a pair of needle nose pliers or a pair of small wir cutters and put a slight kink/bend in the RCA plugs outer shell in order to get a tight fit.  The RCA plugs center pin usually fits tight enough to not bother with. 

      • February 10, 2020
  • ricardo1133
    Contributor - Level 1
    2019-11-19

    tengo un problema con la app x Air, al momento de querer ecualizar un mic, el programa se cierra, esto pasa desde que actualice mi iPad al iOS 13.2.3

    0 134
  • Adriano1972
    Contributor - Level 1
    2019-11-18

    Hi, I've been using an Xr-18 for a few years now and have never had problems with the XAir app, but these days ago I updated IOS to version 13.2.2 and to my surprise was that the app is no longer working as it should. Can anyone help me regarding this? What should I do ? The latest app update is over 2 years old, will anyone solve this?

    read more...
    0 155
  • blanquiazul
    Contributor - Level 1
    2019-11-18

    Hi, I keep trying to raise a support ticket for my mixer but can't get anywhere... the DX626 isn't listed as an option, plus even when I choose a different mode I can't submit the ticket: I just get a constant 'loading' symbol.

    One of the phono ports on the mixer has died, meaning I get no sound from that speaker. Mixer is well within its warranty but I can't get through to customer service!

    Can anyone help?

    20191106_200151.jpg
    read more...
    0 431
  • Worzel
    Contributor - Level 1
    2019-11-14

    I have an original mXC Centre speaker for my cinema room set .18 years old and purée the. So much so I purchased a second hand one for another room set up. But it has a fault sound only comes from the tweeter and nothing from the two other speakers. The cabinate is perfect not been dropped and all connection posts are good. I tested on my original amp then put back my original speaker and that sounds great. So I know it’s not a cable or amp fault. Can anyone help please ideas 

    cheers

    read more...
    0 155
  • chubanina
    Contributor - Level 2
    2019-11-12

    Hi,

    I am currently set with Tannoy RX8F. I Would like to ask what size of cable (mm2) will be enough to power them for 2 meters run? I mean 2x1mm2 or 2x2mm2 or 2x4mm2 etc...

     

    0 180
    • chubanina
      RexBeckett

      @chubanina 


      Hello Tsvetomir, welcome to the forum.


       


      For a 2 metre run, the 1.0mm2 cable should be OK. 2.0mm2 cable is theoretically better but you probably would not be able to hear any difference. 

      • November 11, 2019
    • chubanina
      chubanina

      Hi,


      Thank you for the answer. You might laugh but I currently use 4mm2 and I notice too much low frequencies...


      I think it's an overkill to use such a thick cable...shall i change it? 

      • November 12, 2019
    • chubanina
      RexBeckett


      @chubanina wrote:


      Hi,


      Thank you for the answer. You might laugh but I currently use 4mm2 and I notice too much low frequencies...


      I think it's an overkill to use such a thick cable...shall i change it? 





      @chubanina 


      The thicker cable should not cause a problem with the sound. These speakers can give too much bottom end in small rooms. If you have the space, you could try moving them away from walls and corners. 

      • November 12, 2019
  • KlausEff
    Contributor - Level 3
    2019-11-08

    I have the X32 Rack in use with the firmware version 3.11. Now I found the firmware version 3.12 for X32, dated with November, 8th 2019. The firmware 3.12 for X32 Rack is dated with July, 2nd 2018. Is that also the newest firmware, only with the wrong date?

    read more...
    0 173
    • KlausEff
      DaveMorrison

      @KlausEff 


      I think you are right. They changed some of the dates today. I noticed it when I was looking for firmware 4.0. I think it's release is immenent. M32-Edit 4.0 was released today.

      • November 8, 2019
  • scottcgibson13
    Contributor - Level 1
    2019-11-08

    I'm having some problems with my Tannoy Lifebuds. Like the sound quality but the left bud was choppy (sounded like I was going through a tunnel as it would frequently drop connection) and one day the buds simply stopped pairing with one another so I'm only able to listen to one of them at a time. Have tried re-pairing with my phone as in the manual multiple times to no avail. Please help. 

    read more...
    0 107
  • Jedsterm1
    Contributor - Level 1
    2019-11-06

    Hello, Can anyone help me out with a user manual on the Voicelive Touch? I lost mine in a move. I noticed they do not have it in english on TC Helicons website. Thank you in advance!

    0 204
  • rudomat
    Contributor - Level 2
    2019-11-04

    i´m searching for a product like the HA4700, but much smaller...i only need one stereo jack input, a headphone output, a pan pot plus a mono switch...

    i need it for the drummer, who gets the playalong files with the band panned to the left and the metronome to the right...so he can make his own mono mix...is there a smaller unit to make this possible...?

     

    thanks!

    read more...
    0 89
Go to page