Statistics

298,817 members
182,483 posts
  • Evantv
    Contributor - Level 1
    2020-03-24

    I purchased this new, but been in storage and have lost owners manual. How can I get a manual. My primary question is "does it have a cross-over or filter/do I send it a full spectrum audio signal?

    20200324_131102.jpg
    read more...
    0 184
  • Baljindergill1
    Contributor - Level 1
    2020-03-06

    I need information to contact a local repair person to look at my electric piano. Middle C key is louder, sound is not correct.

    0 134
    • Baljindergill1
      RexBeckett

      @Baljindergill1 


      Hello Baljinder, welcome to the community.


       


      Is your piano a Behringer product? If so, I suggest that you raise a Care ticket for Service Repair explaining your problem. This is done by clicking on Support at the top of the page and then clicking the Create a Care Ticket button. This is only possible if you have completed all the required fields in your profile. Also make sure that you fill-in every required field on the Care form.

      • March 6, 2020
  • Alexis_c_l
    Contributor - Level 1
    2020-02-29

    Hi, I'd like to change the main speaker for my Tannoy Mercury 7.2. Where could I find that part?

    0 149
    • Alexis_c_l
      RexBeckett

      @Alexis_c_l 


      Hello Alexis, welcome to the community.


       


      I suggest that you raise a Care ticket for Spare Parts explaining your requirements. This is done by clicking on Support at the top of the page and then clicking the Create a Care Ticket button. This is only possible if you have completed all the required fields in your profile. Make sure that you fill-in every required field on the Care form.

      • February 29, 2020
  • paulbeteivaz
    Contributor - Level 1
    2020-02-26

    Hi, I need some instruction of how to connect myBehringer UMC204HD to my Yamaha keyboard and to my PC. I need to send a song to my PC and at the same time I need to add a vocal live track.

    I am using W10 and also I have Cubase 5 in my PC.

    Thx,

    Paul

    read more...
    0 179
    • paulbeteivaz
      DaveMorrison

      @paulbeteivaz 


      If you want to record the keyboard and microphone at the same time, you'll need to hook the mic to input 1 and the keyboard to input 2 (or vice versa). Set Track 1 in Cubase to input 1 and Track 2 to input 2.

      • February 26, 2020
    • paulbeteivaz
      paulbeteivaz

      Thank you Dave, but the problem with this setup is that you will hear keyboard from left speaker and vocal from right speaker or vice vesa.

      • February 27, 2020
  • Analizaplazaro
    Contributor - Level 2
    2020-02-20

    Hi please help how can i connect my mixer to my TV and powered speaker?

    thank you

    0 288
    • Analizaplazaro
      RexBeckett

      @Analizaplazaro 


      Hello Analiza, welcome to the community.


       


      We should be able to help if you tell us the make/model of your mixer, TV and powered speaker.

      • February 20, 2020
    • Analizaplazaro
      Analizaplazaro

      @RexBeckett 


      thanks for your reply..


      tv - philips


      mixer - behringer 1202fx


      powered speaker - rockville bp10


       

      • February 20, 2020
    • Analizaplazaro
      RexBeckett


      @Analizaplazaro wrote:


      @RexBeckett 


      thanks for your reply..


      tv - philips


      mixer - behringer 1202fx


      powered speaker - rockville bp10


       





      @Analizaplazaro 


      You should be able to connect the 1202FX Main outputs to the BP10 channel 1 inputs using TRS/TRS cables like these. Without knowing the model of the TV, it is not possible to say how it could be connected to the mixer. Some TVs have two RCA output connectors for sound. If so, you could use a cable like this to connect to one of the 1202FX stereo inputs (5/6, 7/8, 9/10 or 11/12).

      • February 20, 2020
  • RichardH
    Contributor - Level 1
    2020-02-10

    i AM TRYING TO REGISTER MY GRAPHIC EQUALIZER - GEAR4MUSIC ARE SENDING ME PROOF OF PURCHASE BY E-MAIL.  HOW DO I SEND, TO YOU, THE DOCUMENT THEY ARE SENDING ME?  CAN I FORWARD THE E-MAIL THEY ARE SENDING ME.?    

    0 102
  • ldodsworth
    Contributor - Level 1
    2020-02-04

    I'm a newbie to this site and to home audio. I have three questions regarding the FX2000.

    1. Am I too assume that this unit is just an effects processor or is it an interface as well?

    2. I wish to run a mic into it and out to powered speakers. Is this possible or do I have to run it through a mixer first?

    3. I'm also assuming that there aren't USB or SD capabilities to be connected to a computer for recording purposes and that the unit will have to go through a usb mixer.

    Maybe simple and straight forward questions but I'd appreciate any answers. Thanks y'all!

     

    read more...
    0 141
  • katoman91
    Contributor - Level 1
    2020-02-04

    The removable front grills have speaker openings that are strung with cording.  Unfortunately I had a mishap that caused the cords to stretch out and they are no longer straight.  Does anyone have any recommendation of how to take apart to fix?  I removed the screws around the speaker openinf but cannot see a way to separate the grill.

    read more...
    0 114
  • Mayank
    Contributor - Level 1
    2020-02-04

    Hello. Which material would be the best to put inside the ports of the Tannoy XY8F floor standers. 

    0 78
  • jppinbdx
    Contributor - Level 1
    2020-02-03

    Hi !

    I'd want to control my XR18 with both X-Touch and X-Touch Extender connected together on the router (with RJ45 cable) or connected themselves by USB. Is it possible ? Of course, without using a computer !!! I'd just like to use 17 faders in place of 9 !

    Thanks a lot for your ideas ... !

    And sorry for my poor english !

    Best regards,

    read more...
    0 127
    • jppinbdx
      KenMitchell

      HI @jppinbdx , 


       


      Welcome to the community.  Unfortunately, it is currently not possible to use the XT Extender to control an XAir mixer.  A firmware update to add XCTL protocol support would be needed. I "heard" it was in the plans, but have never heard an ETA. 


       


      Ken

      • February 3, 2020
      • Connect both X-Touch and X-Touch Extender to control X-Air XR18
        djtonic Hi KenMitchell, we are in 2022 and still no plans for it???
        • Jun 5
Go to page