Statistics

259,718 members
138,125 posts
  • Rascalrick
    Contributor - Level 1
    2019-06-09

    I have an older version of X Air Edit on my PC and was looking to upgrade today, but it appears that it is no longer available?  I am running version 1.3 on Windows 10, and read about version 1.5.  Does anyone know if they dropped support for this product?

    read more...
    0 225
  • Josuerodriguez
    Contributor - Level 1
    2019-06-09

    My name is Josue, I am a user of X32 and I would like to link 3 consoles in network, and each one can receives the same channels and in this way can be able to use it in PA, Monitors and TV. regards

    0 285
  • NSV11UP
    Contributor - Level 1
    2019-06-08

    What is the easiest way to interface the X32 mixing console with a rack mounted Eventide H9000 effects processor?  I want to handle all audio paths digitally if possible.   Both the H9000 and the X32 make their input/output channels available to a PC based DAW  through their standard USB audio interfaces, but when a DAW is not available or not practical in live situations, I would like to access all  of the H9000's multiple effect channels on my X32 mixing console and be able to route various X32 channels to H9000 effects as needed, through its internal routing.  This wayexternal  effects configurations can be saved and recalled later on the X32.

    read more...
    0 314
    • NSV11UP
      RichardYClark

      Unfortunately both devices are USB clients and rely on the PC being the USB server. So I don't think that there is any easy way to connect them together via USB to route effects send and returns.


      The only way to keep signals in the digital realm would be to add ADAT, Dante or Madi interfaces to the two devices at considerable expense. Or possibly using one of the Klark Teknik convertors that can use the X32's AES50 sends and returns.

      • June 8, 2019
  • JorgeOtero
    Contributor - Level 2
    2019-06-08

    I'm ready to enter the X32 family! I'd like to make sure I can use it as I intend to. Here's the idea:

    -Plug 6 channels in and Send those 6 channels as direct outs to FOH, using the X32 rack as a splitter.

    -Create 6 monitor mixes.

    I'd be using the X32 Outputs as direct outs and the Aux outputs as monitor outs. Would that be the best way to go about it?

    read more...
    0 369
    • JorgeOtero
      RexBeckett

      @JorgeOtero 


      Hi Jorge, welcome to the community.


       


      Do you mean that you want to send the six channels to FOH as analogue lines? If the FOH desk is an X32/M32, you could send them over a single AES50 (digital) cable.


       


      The X32 Rack has eight XLR and six TRS outputs. You can assign these to direct channel outputs, mix outputs and other sources as required. I would use the XLR outputs to feed the FOH desk as you suggested. 

      • June 8, 2019
    • JorgeOtero
      JorgeOtero

      Thanks for the quick reply! So the XLR and TRS outputs can be used interchangeably, that's really good.


      This particular venue has a Digico desk. I'm very new to the world of digital live mixers so it's easiest to do this split in analog.


      I'm hoping for some other venues to have X32 systems so we can plug in digitally. I'll buy a cable to be prepared!

      • June 8, 2019
    • JorgeOtero
      Paul_Vannatto

      Hi Jorge @JorgeOtero,


      Welcome to the forum. The one possible downside of doing it this way is that you will have complete control of the preamps (gains and phantom). If the FOH engineers insists on having preamp control, you will have to use a couple of splitters such as the ART S8 or Behringer MS8000. If they are OK with you controlling the preamps, then what you proposed will work.

      • June 8, 2019
  • JoeWelfeld
    Contributor - Level 2
    2019-06-08

    Hi all, 

    currenty own an x32 rack and the s16, using laptop and iPad for FOH mixes, I am looking to get something with physical faders, and was looking for some advice, if I use the producer can I not use the built in 16 channels and route my x32 and S16 to channels 1-32, do I need 2 ethercon cables from FOH to accomplish this?  Or do save some $$ and go with the Touch and then I run one 1 Ethernet. Connection back to my board, and perhaps also use Laptop at FOH for the RTA functionality? And comments experiences would be great,

    thanks in advanve

    read more...
    0 165
    • JoeWelfeld
      DaveMorrison

      Hi @JoeWelfeld 


      Yes you can use both the Rack and S16 on stage with one cable to the Producer at FOH. The best routing is: S16>Rack>Producer. It's a great setup with extra benefits. You get redundancy if the Rack were to fail (you'd have to move the producer to the stage) and you get two mix engines. More monitor sends.


      If by "Touch" you mean X-Touch (the original-full sized), it does work well. Everything is in banks of eight. The first bank is 8 or 9 button pushes from the last bank though. In combination with a laptop, it's a pretty good setup. 


       

      • June 8, 2019
  • h3
    Contributor - Level 1
    2019-06-07

    On my new XR18 I get a channel input level visible when I plug an intrument in which increases when the gain is turned up and produces a low hum audiable through the speakers on live use. This is when the intrument isnt being played. This doesnt happen when a mic is plugged into a channel. This happens on all channels.. Hi-Z or not. Have done a firmware update but with no effect. Has anyone had this problem? 

    read more...
    0 175
    • h3
      DaveMorrison

      @h3  Hi.


      What kind of instrument? 


      If it's a powered instrument (like a keyboard), it could be a ground loop. Try plugging into the same outlet as the mixer.


      If it's an like an electric guitar, it could be hum induced by lights, neon signs, computers, etc. Try moving to a different spot or try another instrument.


       

      • June 7, 2019
    • h3
      h3

      Hi Dave. Thanks for the reply. Have tried two different acoustic guitars and an electric bass. Tried different instrument cables also and its the same result either through PA speakes or headphones. Chris..

      • June 7, 2019
  • himynameisrenzo
    Contributor - Level 1
    2019-06-07

    I'm having an issue, my X18 is recieving and sending a signal. I can't seem to isolate the reason, it's a brand new unit and nothing is plugged into it.

    Screen Shot 2019-06-07 at 12.53.08 PM.png
    read more...
    0 122
    • himynameisrenzo
      RichardYClark

      Which channel and how much signal? Is this a brand new mixer or have you used it before? You could try a factory reset  This is done by going to the Setup/Connection page in X-Air Edit and clicking on the Initialize box on the right hand side with the XR18 connected.

      • June 7, 2019
    • himynameisrenzo
      RichardYClark

      Is this a brand new mixer or have you used it before? What is the Input source selected for that channel?


      You could try a factory reset  This is done by going to the Setup/Connection page in X-Air Edit and clicking on the Initialize box on the right hand side with the XR18 connected.

      • June 7, 2019
  • thespica93
    Contributor - Level 1
    2019-06-06

    hello,

    I have a subwoofer rated for 2400 W at 4 Ohm. I also own an Europower EP2500 power amp. The specs say in bridge mode the amplifier will run 2400W at 4Ohm. Am I understanding correctly that this amp will work fine for my needs?

    Thank you
    -Nick

    read more...
    0 79
  • staceyhainey
    Contributor - Level 3
    2019-06-06

    I’ve got an M32C with a DL32,   Trying to use Jax 15 & 16 as main outs,,,,,

    got sound on monitors, and on main meters.  But can’t get it out of the aux 

    0 156
    • staceyhainey
      RexBeckett

      @staceyhainey 


      Hi James, the fastest way for us to help you is if you save your scene, zip the .scn file and attach it to your post. Please also tell us which buses you want routed to which outputs - on the M32C and the DL32.

      • June 6, 2019
  • tbridges54
    Contributor - Level 1
    2019-06-05

    I set up my Behringer XR18 yesterday. I was able to connect my Macbook with the X Air Edit software through the internal Wifi Access point feature on the XR18. I set up a WEP SSID and Key and everything was working properly. Today, I went to connect and inserted the key and it is now giving me an error that says "Self Assigned IP". The device is not showing up in my connection list on the X Air Edit software.. Any help?

    read more...
    0 159
    • tbridges54
      ThomasWilliams

      I admit up front that I haven't seen that particular error message, but I work with networks in my day job, so let's try a couple of things:


       


      - Connect the XR18 to your regular network using an Ethernet cable;


       


      - Check to see whether the XR18 is running DHCP when in use as an access point.  If it isn't, try turning that on before you switch back to Access Point mode. 


       


      What I am hoping is that the problem stems from a "duplicate address," i.e., the MacBook and the XR18 chose a same number like 192.168.0.1 or something like that.  Switching the XR18 to DHCP (and setting up the Macbook as a DHCP client) should solve that, if it's the problem.

      • June 6, 2019
Go to page