Hi friends!
I'm trying to connect my PX5 and my Boss es8 in a way where I can use 4cm with both, so I can insert a loop into the PX5 carrying the distorted signal (pedals or amp dist) just to get some fx before dirt and some after.
To clarify, if I use px5 as part of the signal within es8, it works fine, but I can't use lets say phaser or flanger before dist and time based/mod fx after. That's why I want to find a way to connect PX5 I/O AND fx Send/return loop into the es8, so I can use inserts or an fx loop slot to decide what goes where in any way I want.
Es8 signal chain: guitar>input. Compressor into loop 1, wah in loop 2, fuzz in 3, od in 4, dist 5, eq 6. 7 and 8 are free for px5 and this ideal scenario I'm describing. 4cm is being used with the volume loop to determine pre/post pedals. (Amp send into vol return, vol send into amp input, output to amp return)
I know this is kinda complicated/tricky, but I hope someone here can help me. I've tried several connections with no positive results so far.
Thanks!
Hello there, I am new to this discussion board, and also new to electric guitar, so I am wordering, is it best to set the guitar pedal delays (flashback, the prophet, etc...) to the FX loop section of the amp or can it go on a pedal board directly to the clean input channel? I have seen a lot of videos on youtube but no one really explains which one is best. I figured there must be plenty of great guitar players here that possibly know the best answer.
I appreciate your assistance!
Anyone know which usb cable will fit this device?
I very much like the Plethora X5.
I have set up a 'Custom Mode' on my Novation Launchpad Pro Mk3 to manipulate the various CC settings available under Plethora X5 Settings>Global>MIDI>CC Table, and this works brilliantly, as documented, though I share the view of another thread here about the Looper controls.
However, an undocumented feature is sending Program Change (PC) messages and seeing the Plethora switch to the relevantly numbered Board. Is there a way to avoid this behaviour, or do I just need to set the Plethora and Launchpad to communicate on a less commonly used MIDI Channel?
Where can I find presets and installers for my Clarity M? Are there any recent updates like a Netflix preset?
I vaguely remember an option to get additional presets but I cannot find anything online and anything out there is well over 2 years old.
With the loudness war coming back around again as we mix music for streaming and film for Netflix a lot of us Clarity users are praying for new presets while we use the current metering plugins that are all up to date. I hope TC doesnt forget us.
Hi, I loaded Mac Firmware fror Ditto + from TC Electronic site.
It will not install saying "not a verified developer"
what can I do to use the Firmware? I understand it is needed to import/export soundfiles from/to the Ditto +
thanks!
No complaints here about the Plethora. I find that it sounds great and is extremely easy to use. I have been very happy with it so far. I would say this post is more of a request for the product than anything, and since I don't participate in the social media land where i am sure most of that happens, I am going to post here in the hopes that someone will see it and maybe that some will agree with me.
Request #1 -
I think the unit could really use a global tap funciton that carries over to each effect and each board. Having to try and tap two different delays and get the exact time in the middle of playing can be very dificult especially when moving from one song right into another.
Request #2 -
Midi Clock. We are getting a ton of other great midi features that i am currenlty using, however, no Midi clock. This is a little disappointing. It would be super handy to be able to not even have to worry about tapping at all and just being able to either hook up to my other guitar players board and get Midi clock from him or to go direct to the interface running our tracks and getting tempo from that.
Does anyone know if there are plans for either of these?
Those are my two requests for the next update. Keep the awesome pedals rolling out and I will keep using them.
The main reason why I bought tc pedal, was the ability to see dynamic response graphs (based on internet images). But the current software version doesnot show them, only knob range. Where can I find the old software version showing GAIN and DYNAMIC RESPONSE graphs? It's not on tc site anymore
I've got a used TC Dreamscape and it has nice sounding toneprint. I want to load another one but not lose current. Is there a way to know/get/read what toneprint is currently loaded via any app?
The light that indicates that the reverb is engaged comes on when you push the engage button even though no cable is attached to line in. Shouldn't the light come on only when a cable is plugged into line in? Is my pedal malfunctioning?