Statistics

250,909 members
128,128 posts
  • New
    AudioPastor
    Newcomer - Level 1
    2021-09-27

    My Behringer x2222usb is hosting my 3 phantom wired mics.

     

    it recently started presenting audible (master fader only) static. I cannot mute out any channel inputs to remove the static from the mix.

     

    Master faders will increase or reduce the distortion.

     

    Any comment to confirm my phantom mics are issue?

     

    Replaced all cables with known good/new wiring. Mixer Board is 6 months old

     

     

    read more...
    0 1
    • AudioPastor
      Nigel67 Hi AudioPastor. It is unlikely that a microphone is causing the issue if you are muting all the input channels. You can turn the phantom power off using the switch on the rear of the mixer. If the noise goes away then it could be the phantom power supply putting noise on to the ground. Are you using an FX or Aux Send in Pre mode which is then finding its way to the main outs via another route such as the FX Processor. I would advise turning down the 8 orange/red knobs just below the fx processor and seeing if the noise goes away. If you need to know the positions of the pots for setting up again, make sure you take a picture of them. There is also a switch to the right of the FX3 knob. Push it in and that will send the audio to the Sub 1-2 instead of the Main Mix and see if the problem goes away. If that still doesn't fix the issue, then you will have to start unplugging all connections and turning down all the knobs until the noise goes away. If it doesn't then it could be power supply related and the mixer will require repair. Hope this helps
      • 2 hours ago
  • New
    GJERSTER
    Newcomer - Level 1
    2021-09-27

    Hi

    I want to have my Xtouch Extender controlling track 1-8 in Ableton Live and my Xtouch should control track 9-16.

    Both units are updated to 1.21

    My Extenders works perfect alone in Ableton

    My Xtouch can control Ableton, but it has no light in the buttons and the faders stay down on -00

    What have I done wrong?

    Best regards

    Michael

    read more...
    0 2
  • New
    trident
    Newcomer - Level 1
    2021-09-27

    Hi I purchased a2600blue marvel in the states u.s and was curious about when will they be shipping?

    0 3
  • New
    RichardBlack
    Newcomer - Level 1
    2021-09-27

    Hi,

    Delving in the world of minor annoyances here. When I switch my studio on, everything powers up automatically, except my Clarity M.  This has to turned on manually by pushing button 6 on the right-hand side, even though it's power supply is already on.

    Is there a secret setting to fix this please?

    R.

    read more...
    0 2
    • RichardBlack
      PedroRodrigues Hi RichardBlack, please consider that the Clarity M must be powered as you have described. Thank you
      • 47 minutes ago
  • New
    lminnick
    Newcomer - Level 1
    2021-09-27

    Hello,

     

    I have a hotel ballroom/convention space audio upgrade project that has CMS 12 TDC speakers with TEQ 1200-150 enclosures. About 1/3 of the speakers in the ballroom (20 out of 60) have failed and are needing to be replaced. Would the CMS 1201 DCT speaker be compatible for use with the existing enclosure? The speakers dimensionally look identical where the mounting screw holes would match up with the enclosure.

     

    Thank you,

    Luke

    read more...
    0 4
  • New
    QuQusiki
    Newcomer - Level 1
    2021-09-27

    People help me. We need a circuit for the Behringer u-phoria umc22 sound card. Preferably with a voltage value. the number HI - 12A2007R is written on the board itself

    0 3
  • New
    KennethKohncke
    Contributor - Level 2
    2021-09-27

    Hi TC Helicon Developers,

    I have been using the Play Acoustic for quite a few years now and am finding I have need of more from it.

    Here is the challenge I put to you. Come up with a new, closer to fully digital version of the PA.

    The problem I have is trying to adjust settings from behind the mic, guitar and PA. I need to be able to hear what the audience is going to hear to make those adjustments confidently. So what I envisage is the PA being able to connect wirelessly to either a phone or tablet (android), or laptop or tablet, (windows). So I can record myself on the looper, then go out into the venue connected to the tablet and be able to make all the changes to settings there. I would like the settings to be more advanced and more user friendly like the way they are generally displayed and adjusted in a daw. In paticular EQ, Comp, Gate.

    Would be awesome if you could build it!

    Does anyone know of anything like this already on the market?

    Cheers, Ken.

    read more...
    0 2
  • New
    Bru1978
    Newcomer - Level 1
    2021-09-27

    Hi!

    Is not possible use the editor with x-touch one. Why not for the x-touch one and yes for the mini?

    Can I assign parametrers in pro tools?

    Thanks!

     

    Frank

    0 1
  • New
    BenOwens
    Contributor - Level 2
    2021-09-26

    So, I updated.. reloaded scenes.. I did a gig or two.. now .. faders won't move.. select butoone(green) or mute buttons.. scribble strips don't come in.. everything is jacked up.. please help.

    0 20
    • BenOwens
      Paul_Vannatto But you don't give details of the console you updated. Can't help much until we know that simple detail, eh?
      • Sep 26
      • X32 is acting very strange after update 4.2
        BenOwens What details would you like me Paul? I’d be glad to give whatever info you need. Thank you so much with your fast response.
        • Sep 26
    • BenOwens
      BenOwens The console is an behringer X32. Full sized.
      • Sep 26
    • BenOwens
      Paul_Vannatto Thanks Ben for that detail. But what is confusing is that the current X32 firmware is 4.06. Are you talking about X32-Edit? Current version of that is 4.3. Make sure that both console firmware and Edit are current versions.
      • Sep 26
    • BenOwens
      BenOwens

      Not using edit.. just console only. It is the latest firmware. 4.06

      • Sep 26
    • BenOwens
      Paul_Vannatto So what is 4.2 (on the title of this thread)? If you mean that you upgraded to 4.06 and this happened, I would suggest you download the firmware again and re upgrade (using the older USB stick way - place the firmware on the USB stick in the root folder, with no other firmware, insert into the USB jack on the top, press the USB button beside it and turn on the console).
      • Sep 26
  • New
    NickR
    Newcomer - Level 1
    2021-09-26

    Hi I purchased a Q1202USB and the power unit is humming/buzzing it's really noisy and obviously annoying. Is there anything I can do. Or maybe this would be something that Behringer would send me a replacement please??? 

    0 4
Go to page