Statistics

254,239 members
131,905 posts
  • New
    BFAN111
    Newcomer - Level 1
    2021-09-13

    I added another amp and wanted to change my EP2500 to bridge mode operation from stereo.

    It seems like it will not allow me to run it in Bridge mode without enabling the Low frequency filter?

    Is this correct?  I cannot use an EP2500 in bridge mode to power a subwoofer without a low frequency filter?

    read more...
    0 5
    • BFAN111
      DavidKnighton Hello BFAN111,
      No, that is not correct operation of bridge mode. According to the manual, you need only push switch 6 & 7 to the ON position to enable bridge mode. Also note that parallel mode must NOT be active, so switches 4 & 5 must be in the OFF position. The remaining switches/controls for INPUT 1 are optional. The manual does state that the the INPUT 1 options are used specifically for bridge mode operation, meaning INPUT 2 controls are N/A. This statement does not mean that the controls need to be engaged for bridge mode.
      • Sep 13
    • BFAN111
      DavidKnighton
      • Sep 13
  • New
    HawaiianKidd75
    Newcomer - Level 1
    2021-09-09

    I have had the NX3000 for about 3 years hadn't had an issue at all.  Practiced as normal and the amp started blowing out bright white smoke.  It isn't dust related as it is in a Flight Case.  Still works ,however, I recently purchased the NX4-6000 from Sweetwater Mid July.  Second time being used was yesterday during band rehearsal and it duplicated the exact issue I experienced with the NX3000 and every channel went into Protect Mode.  Fans blew with much more force than normal operating conditions and all I had was 2 Peavy 12" Mains and a Peavey 500w Wedge.  Not nearly enough load to cause this.  Is this a defect or has anyone else ever experienced this issue. 

    read more...
    0 11
    • HawaiianKidd75
      john0121 Hi, unfortunately this sounds like a hardware fault in with the amp, please fill out the service request form via the support button at the top of the page and our team will arrange a repair with you.
      • Sep 10
  • New
    NicholasKelly
    Newcomer - Level 1
    2021-09-08

    I have a fried pcb board for an s16 at church. We need a replacement part bad! 

    0 11
    • NicholasKelly
      KyleJohnson Hello, Kyle here with Music Tribe. For spare parts help please visit our Support page and submit a Spare Parts ticket.
      • Sep 8
  • New
    tet024
    Newcomer - Level 1
    2021-09-05

    Good Morning, 

    I purchased 2 x iNuke DSP and I would like to hook them up to a DIY Home Theater Speaker.  The Idea is to use the Xover on the iNuke rather then building a passive crossover. My Question is:- Is it possible to have the woofers on Channel A with a 2 Ohm Impedance then the Tweeter @ 8ohm on Channel B ? Would that cause any issues ? Or effect Sound Output? 

     

    Regards,

    Etienne

     

    read more...
    0 10
  • New
    rsparkle22
    Newcomer - Level 1
    2021-09-03

    Is it safe to use pmp 4000 powered amp without speakers connected. I would like to use headphones and do home recording on the pc with tracks adding vocals. Thanks

    0 15
    • rsparkle22
      WilliamR Hello, Yes, solid-state power amps are safe to use without a speaker load. Only tube-driven amplifiers should not be run without a speaker load.
      • Sep 3
    • rsparkle22
      rsparkle22 Thank you.
      • Sep 3
  • New
    Petethetrump
    Newcomer - Level 1
    2021-08-30

    Hi does anyone know where I can purchase a power circuit board for the Berhinger Air X 18 as ours has blown. We get 360 vaults going in and even part way across the board but then it splits and only some of the components are getting the voltage , in short it's dead . 

    read more...
    0 20
    • Petethetrump
      Dale_M Hi there if you are looking for parts simply go to the Support tab above and select Parts so the team can advise price and availability.
      • Aug 30
    • Petethetrump
      Petethetrump

      Nobody has replied and we really need the part or the X 18 is useless to us . I’d appreciate someone’s attention to this if possible?

      • Sep 2
  • New
    jp182
    Newcomer - Level 1
    2021-08-30

    I just bought a second hand AMP800 and I've plugged 3.5 to 1/4 cable into the input L & R into the amp with a pair of headphones plugged into the headphone jacks on the front.  

     

    Not only do I not get any sound, I also don't see any of the LEDs on the front moving which is making me think the AMP itself is not working.  I've tried multiple input sources in both input A and input B; same result. 

     

    Any other suggestions before I email the buyer to get a refund on a defective unit?

    read more...
    0 11
    • jp182
      ChrisEdwards1 Hi jp182, Are you aware if the unit was supplied with its original power supply or a third-party power supply? If a third-party power supply, I would recommend double-checking all specifications to ensure they match correctly including the polarity.
      • Aug 29
  • New
    SJFlesch74
    Newcomer - Level 1
    2021-08-21

    Hello!

    Does anyone know how to get in contact with someone regarding repairs for a Behringer power amp? We submitted a ticket (Ticket Number: CAS-480871-P8N9F6), but it was closed and we received no response. Any help would be greatly appreciated.

    Thanks!

    read more...
    0 23
    • SJFlesch74
      ChrisEdwards1 Hi SFlesch74, upon checking your case I can see one of my colleagues reached out to you on 20/08/2. Could you please double-check your spam and junk folder for their response? We have seen our replies route to this location before.
      If there is nothing in your spam/junk folder could you please let me know and provide an alternative email address? I will then request they reach out again.
      • Aug 21
  • New
    gelito
    Newcomer - Level 1
    2021-08-21

    Hola. Hace un par de meses compré este artículo a través de Thomann junto a la U-PHORIA UMC202HD. Las conexiones que tengo son del micro de condensador con xlr a una de las entradas del ULTRAGAIN (línea 2)y desde este una salida con xlr a una de las entradas de la interfaz, la cual está conectada por usb al pc. Creo que hasta ahí está todo correcto. Luego al dar volumen de entrada al micro (un RHODE NT1A), suena un ruido de como de metralleta de clips horrible, lo cual empezó a ocurrir desde hace varias semanas. Sin embargo, en el otro canal tengo conectado de la misma forma otro micro Presonus con AUDIOBOX USB96 y no ocurre lo mismo, igual que si todo lo anterior lo conecto a la línea 1. Por favor, ¿podéis decirme si estoy haciendo algo no correcto?. ¿Se puede deber a un problema en el ULTRAGAIN?. Os dejo un archivo para que lo comprobéis. Gracias.

    read more...
    0 67
  • New
    Timmy456789
    Newcomer - Level 1
    2021-07-29

    I havent gotten a response from the emails that i have sent to Todd Cowan regarding case 474738-g2ny4y1-nu600

    0 57
    • Timmy456789
      DavidKnighton Hello Timmy,
      I will ping this to our spare parts team and see what can be done to improve your experience. As always, be sure to check SPAM and JUNK folders, as often our emails can get flagged on the customer's end.

      EDIT: I can see a response from the spare parts agent from today, July 29. You should have the response in your inbox from [email protected] I've asked the agent to resend the email just in case you missed it.
      • Jul 29
Go to page