Statistics

254,576 members
132,278 posts
  • New
    jmsernell
    Newcomer - Level 1
    2021-10-21

    Hello,  I'm trying to get a replacement power supply as mine has sadly disapeared.  How can I get a hold of a new power supply?

    Thanks!!!!!!

    0 4
    • jmsernell
      Dale_M Hi there please go to the support tab and select Spare Parts, the team will advise you.
      • Thu at 5:02 AM
      • behringer Xenyx Q802USB
        jmsernell Thanks Dale, I had sent a message through there last week and have not heard back yet.
        • Fri at 8:12 AM
  • New
    Hutchorr
    Newcomer - Level 1
    2021-10-13

    I have been looking at the following amps and not sure which series would best fit my needs.  EP4000, NX3000 or NU6000.  I know very little about these amps so there might be a better option other then these three.

    I will be driving two 18" subs that can handle 600w RMS each. They will only be playing lower frequencies.  I can purchases these subwoofers in either 2 ohm or 4 ohm setup.  What ever amp is going to give me the best power in either setup works for me.  My Proccessor will be handling all cross overs, filters and equalization.

    Question is which amp would you suggest for my application.  I've known guys who have used the EP4000 in bridge mode on a pair of these subs (2 ohm) wired in series.  They say it is a great setup but also the NX or NU series might be a better fit.

    Thanks in advance.

    Hutch

    read more...
    0 12
    • Hutchorr
      PedroRodrigues Hi Hutchorr I think that for your set up the EP4000 is a good Amp for your set your set up but the NX4-6000 might be also a good option, please see the specs for the NX4-6000 below, I hope this helps you selecting the best AMP for your needs.
      • Oct 13
      • Need help with an Amp Selection
        Hutchorr Thank you for your suggestions. Any particular reason why you'd suggest the NX46000 over the NX6000? Both do 3000w x 2 @ 4 ohm. Do the Class D amps reproduce bass better then a class A/B? I do know they run cooler and more efficient.
        • Oct 13
  • New
    Mgisselman
    Newcomer - Level 1
    2021-09-27

    Hi! I bought a used GX110 a few weeks ago, and this weekend I took it a bit far with the volume (since it couldn't be heard over the drums via Messenger..." and it started to smell burnt. After letting it cool off for a few days and trying it out again, something is messed up with the sound and it is especially something wierd with the bass.

    I am aware that the GX110 is no longer available, but do you have any model similar to it? Loved the sound in it.

    read more...
    0 9
  • New
    jdinsdale
    Newcomer - Level 1
    2021-09-24

    Hi,

    Id like to get a copy of a schematic for F1220D powered monitor.

     

    Thanks Jeff

    619-787-4381

    1 12
  • New
    DEFF123
    Newcomer - Level 1
    2021-09-22

    Please answer my 2 amplifier repeated question

    0 9
  • New
    DEFF123
    Newcomer - Level 1
    2021-09-22

    The lights flicker on and off when I turn it on and when I turn it off.  What do you suggest?

    0 4
    • DEFF123
      DEFF123 I'm awaiting your answer.
      • Sep 22
    • DEFF123
      Nigel67 Hi Deff123. Unfortunately the device appears to be faulty. If you have tried another mains cable and mains socket and the LEDs are still flickering and you get no audio at all, then it needs to be serviced. You mention that the unit is new. If it is under 30 days old, then please go back to the shop that you purchased the unit from and ask for a DOA replacement. If it is over 30 days old, please send us a Technical Support ticket as mentioned by my colleague below and we will help you further. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Technical Support tab and submit a ticket.
      • Sep 22
  • New
    DEFF123
    Newcomer - Level 1
    2021-09-22

    I have a new PPA550BT the power  box lights flicker on and off when I turn it on.  The also flicker when I turn it off.  What do I do?

    I have no  sound on my PA

    0 6
    • DEFF123
      DEFF123 What do I do?
      • Sep 22
    • DEFF123
      KyleJohnson Hello, Kyle here with Music Tribe. Please contact our tech support directly by clicking on Support and then Technical Support.
      • Sep 22
    • DEFF123
      DEFF123

      • Sep 22
  • New
    JavierBode
    Newcomer - Level 1
    2021-09-22

    I have 2 pcs of NU6000 BEHRINGER AMP needing to be replaced the AMP BOARD.  Please provide information about where to buy 2 pcs of AMP BOARD and the price. I need orientation toward solving this issue. THANK YOU!

    0 11
    • JavierBode
      Nigel67 Hi JavierBode. Please contact our spares department and they will be able to help you further. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Spare Parts tab and submit a ticket. A colleague will then get back to you with pricing and availability. Many thanks
      • Sep 22
  • New
    Vin1
    Newcomer - Level 1
    2021-09-14

    I want to register my pa BEHRINGER C200, I bought it last month, I would like to register the product to benefit 3 years warranty, can you tell me what is further step to do to benefit extended 3 years warranty. My cell phone to contact me is 514-290-0772. My name is Vinh.

    Thanks!

    read more...
    0 10
    • Vin1
      PedroRodrigues Hi Vin1, please consider that you must submit an assistance request directly with our Tech Support Team by following the link below so we can assist you on the register process for your unit and perform the necessary verification to access if you qualify for the extended warranty. Please provide the serial number for your unit located on the unit and also attach the original invoice for this purchase Thank you
      • Sep 14
  • New
    BFAN111
    Newcomer - Level 1
    2021-09-13

    I added another amp and wanted to change my EP2500 to bridge mode operation from stereo.

    It seems like it will not allow me to run it in Bridge mode without enabling the Low frequency filter?

    Is this correct?  I cannot use an EP2500 in bridge mode to power a subwoofer without a low frequency filter?

    read more...
    0 5
    • BFAN111
      DavidKnighton Hello BFAN111,
      No, that is not correct operation of bridge mode. According to the manual, you need only push switch 6 & 7 to the ON position to enable bridge mode. Also note that parallel mode must NOT be active, so switches 4 & 5 must be in the OFF position. The remaining switches/controls for INPUT 1 are optional. The manual does state that the the INPUT 1 options are used specifically for bridge mode operation, meaning INPUT 2 controls are N/A. This statement does not mean that the controls need to be engaged for bridge mode.
      • Sep 13
    • BFAN111
      DavidKnighton
      • Sep 13
Go to page