Statistics

241,386 members
117,655 posts
  • New
    m944
    Newcomer - Level 1
    2021-06-27
     
    hello I have to replace the power transformer of the ep2500 amplifier that I bought about five years ago.
    The primary of this amp is broken I think due to the electrolytic capacitors which are probably shorted.
    I would like to know if the cost of these spare parts to evaluate the replacement thanks Martore giuseppe email martore [email protected]
    read more...
    0 16
    • m944
      KyleJohnson Hello, Kyle here with Music Tribe. To order parts please click on Support and then Spare Parts to submit a ticket.
      • Jun 27
  • New
    JimBrettell
    Newcomer - Level 2
    2021-06-25

    Hi, I've just taken delivery of a PMP580S amp. There is a button marked 'Speaker Processing' but the manual only tells you that the button exists!

     

    Anyone any idea what it does or what it's used for?

    0 24
  • New
    hiswkf
    Newcomer - Level 1
    2021-06-23

    Good morning, I was wondering if it was possible to convert an older LGFP14K from US mains to EU mains? If so, what would that entail?

    0 16
    • hiswkf
      DavidKnighton Hello hiswkf,
      Check the voltage spec on the rear panel near the mains input. If it does not specify operation up to 230V, then I would say not possible, at least not without some involved modifications.
      • Jun 23
  • New
    Myron2099
    Newcomer - Level 1
    2021-06-14

    Hi guys how can I connect my UMC22 board to my Nobsound A8 valve amplifier with AUX input?

    0 27
    • Myron2099
      DavidKnighton Hello Myron2099,
      The aux input is likely a stereo connection. This means you'll need a stereo breakout cable to connect the UMC 1/4" outputs. See the cable in the following link. This should do the trick.

      https://hosatech.com/products/analog-audio/stereo-breakouts/hosa-breakouts/cmp-150/
      • Jun 14
    • Myron2099
      Myron2099

      therefore connecting the 6.25 to 3.5 in the amplifier I have the sound output from the speakers.
      and i can hear the sounds from the imac via usb! even plugging in a microphone and using garageband?

      will i have better sound gain? is the card preamp?

      Thank you so much so my dilemma solved me

      • Jun 14
      • UMC22 to tube Valve amp
        DavidKnighton I'm not sure I understand the follow up question. If you're asking if using a microphone through Garageband will sound better, well that's a matter of opinion really, and depends wholly on your ability to mix sound.
        • Jun 15
  • New
    Daviddobson
    Newcomer - Level 1
    2021-05-21

    Can behringer amps ever be repaired by behringer? Alternatively, can you buy the amp boards from behringer?

    0 40
    • Daviddobson
      DavidKnighton Hello Daviddobson,
      If you have a defective amp, you can submit a SERVICE REQUEST ticket via the SUPPORT tab at the top of the page. Alternatively, you can also submit a SPARE PARTS ticket via the SUPPORT tab.
      • May 21
  • New
    AliJasimALOhimed
    Newcomer - Level 1
    2021-05-18

    When KM-1700 will be available?

    0 42
  • New
    Sourabh396
    Newcomer - Level 1
    2021-05-17

    Which amplifier will be suitable for Behringer 1C-BK passive speakers ?

    0 41
  • New
    Badsoulzz
    Newcomer - Level 1
    2021-05-14

    Hi ,

     

    My Position in Bali Indonesia,

     

    Can i get contact disrtibution Behringer Indonesia ? 

    Honestly difficult to get amplifier behringer such as KM750 ,KM1700 i love it...

    0 47
  • New
    Djgatos
    Newcomer - Level 1
    2021-05-13

    Hi I have a question I have 8 of this line array.      

     

    https://www.seismicaudiospeakers.com/products/passive-2x10-line-array-speaker-with-dual-compression-drivers

     

    Question how many pd3000 any for my 8 line array somebody can help me please ...

    read more...
    0 58
    • Djgatos
      DavidKnighton Hello Djgatos,
      The SA cabinets are 16 Ohm and require about 1,200 watts per cabinet. By running multiple boxes in parallel, you could get 4 cabinets down to a 4 Ohm load, however the power requirements for that many speakers would far exceed the PD3000 power output. You would need an amplifier that could achieve 5,000 Watts @ 4 Ohms so it could properly handle the peaks. The PD3000 produces 1,500 watts per channel, and does not appear to be a bridgeable amplifier, so 1,500 watts is your absolute maximum output @ 4 Ohms. The amp that I would recommend would be the PLM12K44, which can deliver 3,000 Watts per channel at 4 Ohms, or you could bridge for effectively double the output power, which is what I would suggest for these speakers. You would need a single PLM12K44 amplifier to adequately power all 8 boxes in a standard stereo L/R configuration. Not including the subs mind you.
      • May 13
    • Djgatos
      Djgatos

      My Sa audio cabinets I switched the wire to 4ohms each cabinet you think 1 amp can handle 2 boxes 1 each side?

      • May 14
      • Pd3000 lab gruppen power amp
        DavidKnighton At 4 Ohms, the amplifier will deliver up to 1,500 Watts per channel. If you chain two cabinets at 4 Ohms each, your load ends up being 2 Ohms on the amp, which ends up producing less watt output, about 1,000 Watts. I would recommend. In this case I would suggest 1 amp channel per box, which means you'd end up running quite a bit of cabling. I'm not sure how the power requirements change as you switch the cabinet to 4 Ohm load. Maybe you can switch it to an 8 Ohm load, I think that would be better, because then you could chain 2 cabinets for a 4 Ohm load. The amp will perform the best at 4 Ohm loads.
        • May 14
    • Djgatos
      Djgatos

      Ok I'm going to tried working with 2 cabinets with 1 amplifier and we go from there thank you for you help beacuse I'm going to buy 4 pd3000

      • May 14
  • New
    DKPERRY
    Newcomer - Level 1
    2021-05-11

    I have a Behringer GX 108 practice amp.  I've had it a while and never had a problem.  Went to turn it on the other day and nothing.  It was dead.  No sign of life.  it's getting power and the ceramic fuse appears to be good and checked out with my meter.  Any suggestions?  Anyone have similar issues?

    read more...
    0 45
    • DKPERRY
      ChrisEdwards1 Hi DKPERRY, if you have not yet done so I would recommend opening a Service request. This can be done by clicking on the support tab at the top of the page, scroll down and click on the Service tab and submit a ticket.
      • May 11
Go to page