228,637 members
103,546 posts
  • New
    Newcomer - Level 1

    Hi everyone, 

    I am new to musictribe so hello from the UK.

    I wanted to post on here as I am looking for a pair of Turbosound Impact 120 speakers. I have the Impact 180 sub and was wondering if anyone knew where I may be able to get a pair of 120's?

    Many thanks in advance for any help/suggetions. 

    Kind regards, 


    0 30
    • Djmrflibble41
      Dale_M Hi there can I ask you to submit a ticket as the Pre Sales team are not on Community, let me know the case number and I will ensure it gets to them.
      • Apr 1
  • New
    Newcomer - Level 1

    My ip500 v2 is powering down after only 1 hour of being powered up.

    any one have any suggestions what could be going on. 

    it just shuts off all by itself.

    0 19
    • jeffwoods
      Dale_M Hi there can you advise if the unit is getting hot at all before shutdown? It may be wise to go to the support tab at the top of the page and raise a Technical support ticket so we can help you.
      • Apr 9
      • ip500 shutting down after 1 hour power up
        jeffwoods Thanks, the MusicTribe team got me fixed up with the correct part.
        • Apr 9
  • New
    Newcomer - Level 1

    Had an outside gig powered by clients generator and I suspect the voltage dipped or spiked. The LEDs show the music input but no sound. Is there anything I can do on my end, or is it fried? :( The firmware is up to date.


    0 28
    • danjamowf
      RexBeckett Hi danjamowf, it seems likely that the IQ12 power supply was damaged. I suggest that you open a Care ticket.

      At the top of this page, click Support then scroll down the new page and select Service. Make sure that you enter all required (*) data before clicking Submit. The Care team will respond by email.
      • Mar 18
  • New
    Newcomer - Level 1

    Can you run ultranet to the iQ15's and use the crossover to send XLR to another brand sub? 

    0 38
  • New
    Contributor - Level 2

    I am using my iQ8's and 15B in our small studio/rehearsal place and want to set up the speakers with XLR connections from our analog rehearsal mixer and Ultranet to the X32 in the control room used for recording.  I had all the speaker inputs set to 'Auto' but the X32 was not turned on at the time as I understood the iQ speakers would 'Auto' to XLR when no Ultranet signal was detectedwhich is what I want for general use for other users.  Only I use the X32 when recording so when I turn on the X32 I expected the Ultranet connection to take priortity.  This set up is to make it compatible for both the analog desk and the digital desk without the others having to change the input selection on the back of each speaker (which means pulling them all out to access the back panel) Is this not how the 'Auto' input should work or am I missing something.  To avoid the hiss and use XLR I had to switch the inputs to analog and then turn the speakers off and on again before they stopped hissing.  Any advice would be appreciated


    Many Thanks



    0 19
    • MichaelHutton
      GaryHiggins I believe you can only connect to one or the other, digital via the ultranet or analog via the xlr not both (physicaly connected) at once. I also believe the auto is only for eq not for the analog/digital connectors.
      • Mar 13
  • New
    Newcomer - Level 1

    Hi. I'm confused with using my Milan sub.

    I connect from my mixer into the sub and then from the thru output up to the tops.

    The confusion comes from the Milan's signal led. I rarely see it working! It only shows a signal when the mixer output is high AND the milan output level is high. Oh, it sounds great but it's too loud for some of the venues I play!

    My experience and expectations would be that the speaker would display a signal received via the led and then you'd turn it up to suit the venue. Or you'd set the speaker level high and then control the overall volume from the mixer, however this could add unwanted noise.

    I thought the idea of a signal led is to display that the speaker is receiving a safe level before it would clip or trip the limiter. At the same time it would also ensure you're not introducing noise.

    I tried by having the mixer turned up fully but it still wouldn't show a signal until I turned up the speaker to almost full volume as well.

    I've followed the manual but it offers no explanation.

    With lockdown coming to an end and gigs starting up again, I was hoping I could use the milan with a bit more confidence.

    If you could reassure and help, it'd be great, thanks.


    0 29
  • New
    Newcomer - Level 1

    I have two loud speakers. I had a friend use them and now one makes a static/ screech when it is turned on even without a cable attached. The other appears to have no high end. Is the possibly a simple solution or will I likely need to send them in to be repaired? 

    0 33
    • Yakoba
      DavidKnighton Hello Yakoba,
      It definitely sounds like your friend may have caused some damage to your speakers. I would suspect they blew one of the high frequency drivers in one unit, not sure about the other with the screeching sound. I suggest opening a service request ticket using the SUPPORT link at the top of this page.
      • Feb 8
  • New
    Newcomer - Level 1

    I have 2 ip1000s and 1 of them went into half power. To match the work up I have the gain this one up.

    ive checked to see if any drivers have blown and they have not.

    im at a loss, any help would be appreciated 


    0 33
    • KieranPollard
      john0121 HI Kieran, if the level has dropped significantly on one of your speakers but not the other I would first recommend swapping the source material and cables to ensure that isn't the cause of the problem. Further then that it could be a problem with the amplifier. If you submit a tech support ticket via the support button at the top of the page then we can work through some more troubleshooting with you and arrange a service if necessary. Thanks
      • Feb 1
  • New
    Newcomer - Level 1



    gibt es auch eine normale Anleitung und nicht nur eine QuickStart Anleitung für den Turbosound iQ12?

    Wo finde ich die Software zum verbinden PC mit den Lautsprecher?


    Gruß Nusty

    0 50
  • New
    Contributor - Level 1


    Is there a way to use the line level input in the IP 1000? Nothing is marked for line level, when using keyboards etc, not using

    a dynamic microphone. so will have some mic lines.


    Thank You


    0 40
Go to page