Could anyone provide some more detailed info on the MAIN IN jack on the back of the B205D and B207MP3?
All the manual has to say is that you use it to connect the output from another speaker. And while the specs section gives Sensitivity and Input impedance figures for the Channel 1 and Channel 2 inputs on the front, all it says about MAIN IN is that it's a combo XLR/TRS jack.
I'm wondering how versatile this MAIN IN is...could I essentially use it as a third input? Can it accept a monitor out signal from a board? A mic? An instrument like a guitar or bass?
Also curious how the gain adjustment would work in this situation. I would think that the MAIN LEVEL knob would control the level of whatever is input to the MAIN IN. Then you could adjust LEVEL 1, LEVEL 2 and LEVEL 3 (CD) to get levels relative to the signal on the MAIN IN. Am I on the right track?
Thanks in advance, I hope someone who knows these speakers can help!
Looking for a suitable way to carry this monitor as the duct-taped box is falling apart! HELP!!!
When I plug the 205-D monitor in I'm hearing a distorted sound from the speaker. This occurs even with all volumes turned down. I have tried using a different power cord and multiple power outlets. Can anyone tell me what is happening? Any fix or is this something that needs to be sent in for service?
Hi everybody!
I am looking for the part (number) that separate signals to tweeter and main speaker of an Eurolive VS1200F?
does somebody knows it part#, name, cost or anything that can help me to fix a pair of floor monitors that I can only have sound of its tweeters?
Hi there, I have a behringer eurolive f1220d floor monitor. It has been stored in my hut for over a year. I plugged it in to test it and at first it worked then after about 10 minutes it started making a farting noise then nothing. If I switch it on and off I'm only getting audio from the tweeter. I checked the main speaker in another cab and it's fine so it seems like an amp issue. Are these sold as a spare part. If so how much do they cost and where can I get one thanks
Were these ever produced with a wrinkle paint finish?
I'm interested in the B205D, and I see it has a hole in top into which an adapter may be placed, and then a boom attached to the adapter. But I can find no mention anywhere of whether this adapter is included or is it purchased separately, or if it's a part that Behringer makes and what would be the part model #, and if Behringer doesn't make it, then where would I get one, and what specs would it have to match.
What I'm NOT asking about is this adapter here...
https://www.sweetwater.com/store/detail/B105DStdMnt--behringer-microphone-stand-mount-for-b105d-and-b205d
...which is the adapter that would go beneath the B205D; i.e., the B205D would go on top of this adapter. I'm asking for details about the adapter that would plug into the hole atop the B205D, and then a boom would be attached to said adapter I'm searching for.
The adapter I'm talking about is clealry shown here: https://www.youtube.com/watch?v=jjTBJLHkZVg&t=57s
Bottom line... what's the adapter called / what's the model #, and where would I find it? Thank you!
Help? Overheating? But what component?
It works fine for a while then it starts to cut out. When it does the Clip light and Power light will cycle on/off together for a bit, then starts working again.
Hard to pinpoint as the cause is intermittent and not repeatable.
I have a bandmate with the same issue with his. My other 3 are fine. Anyone else have/solved this issue?
I am running 2 behringer b210d PA speakers thrugh the mackie to the macbook and using logic pro X. I cannot seem to get any of the effects or the guitar sounds that come pre instaled or plug in with logic. It just sounds like a clean guitar? what am I doing wrong here.
please help I am going batty trying to find the cure> heres the set up (photos)
Thank you for the info. I’ve read the manuals but clearly not well enough. I don’t want the effects from mackie I want the guitar plug ins from logic (or garage band or any saws).
Sorry if this was the wrong place because . Yes, the speakers work. So that’s good!
Hello. I have an Xair 12 and would like to use passive stage monitors to eliminate a few cables on the floor. What would be the best way to do this?