Statistics

223,683 members
97,900 posts
  • davedockweiler
    Newcomer - Level 1
    2020-08-11

    I purchased Behringer wireless mics ULM200. The USB has cracked open and no longer works. It's never been dropped or abused. Can I get a new one? 

    Dave

    0 26
    • davedockweiler
      JoeRivers96 Hi Dave,

      Please submit a support case using the SUPPORT tab at the top of this page and we'll see what we can do to assist further here.
      • August 11, 2020
  • Richly
    Newcomer - Level 1
    2020-07-17
    Hi everyone, Looking for a basic lapel mic for online piano teaching. I have a great little Rode Smart Lav+ (designed for plugging into a phone), but unfortunately -- according to Rode -- it needs two adaptors to use in a mixer like this (one to convert the TRRS-to-TRS plug, another to convert TRS phono-to-XLR which also converts the phantom power from 48V to the 3~5V thee mic needs to operate). Who knew this was so complex!?! I don't need anything too high-end, it's just for VOICE (the electronic keyboard plugs straight into the 2nd mic input -- easy!), so i thought maybe an electret mic like this https://www.jaycar.com.au/stereo-lapel-microphone-with-headphone-outlet/p/AM4013 might do the trick. It's very cheap, BUT i think it will have the same problem because, from what i read of electret mics, they all seem to need a small level of power, which the phono jack won't provide through this mixer. Any ideas? Should i be looking for a dynamic lapel mic? Or maybe i just get the adaptor and be done with it. To me it just feels so round-about (so many adaptors!!!!) Any thoughts welcome, thanks :) Richard
    read more...
    0 29
    • Richly
      Richly Here's the setup i was hoping to use... but failed :(
      • July 17, 2020
    • Richly
      Richly Even Lav mics with XLR plugs like this Shure mic (https://djcity.com.au/product/shure-cvl-bc-tqg-centraverse-wireless-lavalier-mic/) seem to say they need only 5- 10V, so will the on-board 48V phantom power actually work with this? More than what i wanted to pay for another basic mic, but maybe i need to go for something like that... ?
      • July 17, 2020
    • Richly
      RexBeckett You are correct. All electret mics need a power supply. I haven't seen a dynamic lavalier mic for years - electrets are much better and smaller. I think your best bet is to get the Rode adapters. Rode products are very good and the adapters probably cost less than another mic with battery or phantom power options.
      • July 17, 2020
      • Wanting recommendations on a basic lapel mic to plug into a Xenyx Q802 USB
        Richly Thanks Rex. I guess it's only *one more* adpator, lol!
        Just seems weird that to plug in one simple Lav mic i need:
        LAV_Mic --> TRRS-TRS adaptor --> phono-XLR-and-power adaptor --> MIXER_input
        ...not to mention i'll probably have to add the extra 6m extension to give a bit of range with the lead! Surely means buzz & hiss entering at each point!
        • July 17, 2020
      • Wanting recommendations on a basic lapel mic to plug into a Xenyx Q802 USB
        RexBeckett I think it is the same number of adapters that you tried already. You just swap the 3.5mm/6.35mm adapter for the Rode 3.5mm/XLR (VXLR+) one. If you want to extend the cable, use an XLR cable between the Rode adapter and the mixer. The balanced cable is less likely to pick-up noise.

        You can get lapel mics that are fitted with XLR connectors and use phantom power. They are usually pro-level /broadcast products and fairly expensive. I have seen budget versions on Amazon/Ebay but never been tempted...
        • July 17, 2020
  • pratikc
    Newcomer - Level 1
    2020-07-16
    I want to measure the sound frequency as 400, 968 and 2063 Hz. can anybody share me which microphone setup will work fine. I am going to use onboard audio jack of my PC
    0 52
    • pratikc
      RexBeckett Most measurement mics require phantom power that is not provided by a PC audio input. You could use an external phantom power supply but a better option is to use a measurement mic that has a USB interface. I use the miniDSP UMIK-1 which works well with sound measurement software on PCs, tablets and phones.
      • July 16, 2020
  • PopIcon
    Newcomer - Level 1
    2020-07-09
    Can you tell me where I can get four of these please?
    0 47
    • PopIcon
      Dale_M Hi, you simply need to go to support and raise a care ticket, chose spare parts and submit,the team will get back to you as soon as possible.
      • July 10, 2020
  • willox
    Newcomer - Level 1
    2020-07-09
    Hi guys. I recently bought my new Behringer C3 but yesterday I broke my mount for my microphone stand. Does anybody know where to get a new one? I tried to fix it with glue but the final result were not very promising. Please help, I want to continue recording...
    read more...
    0 49
    • willox
      RexBeckett Try this: At the top of this page, click Support -> Care -> Create a Care Ticket and select Type: Spare Parts. Make sure that you enter all required (*) data before clicking Submit. The Care team will respond by email.
      • July 9, 2020
  • TsolisKostantin
    Contributor - Level 2
    2020-07-06
    Good day, I would like to have specification sheet of BA 85a, including: polar pattern and Frequency response diagrams. Behringer provides some specifications but I also need: Field Sens. on MV/Pa, Self Noise and SNR Ratio. Also I would like to have Polar pattern diagram (graph). Yours,
    read more...
    0 46
    • TsolisKostantin
      NicJonesMT Hi there.

      All publicly available specifications that we provide can be found in the QUICK START GUIDE



      This is the only information that we provide.
      • July 7, 2020
    • TsolisKostantin
      TsolisKostantin You do not provide self noise or polar pattern diagram? Are your products oriented as "tools" or as "toys"? All these specifications not provided are so bad that you choose not to provide them or you don't take your clients seriously enough to provide them with specs which even some Chinese makes provide and are IMPORTANT for mic placement and use?
      • July 7, 2020
  • TsolisKostantin
    Contributor - Level 2
    2020-07-06
    Good day, I would like to have specification sheet of ULM300M (is the microphone of ULM302 set), polar pattern and Frequency response diagrams. Behringer provides some specifications but I also need: Field Sensitivity, vSelf Noise, SNR Ratio, Max SPL. Yours,
    read more...
    0 41
    • TsolisKostantin
      NicJonesMT Hi there.
      As on your other post, All publicly available specifications can be found in the Quick start Guide.
      • July 7, 2020
    • TsolisKostantin
      TsolisKostantin As on my other post, I am really sorry that I bought behringer microphones which seems to hide important data about mic performance and setup. Will stick with my other makes from now on and inform future customers about behringers choice. From Telefunken and Shure to AKG and EVEN T.BONE most of the companies provide all data needed to setup each mic the way you need. Maybe Behringer has a different approach which does not suit us.
      • July 7, 2020
  • Rihern77
    Newcomer - Level 1
    2020-07-04
    Hello all...recently purchased ULM302MC dual mic system......Channel 1 and Channel 2 have a good wifi signal, however, channel 2 has no audio signal. Looking to troubleshoot the receiver or mic to determine which is bad...any ideas???
    0 54
  • tdehan
    Contributor - Level 2
    2020-06-14
    I want to record vocals and acoustic guitar at the same time using my UMC404HD interface. I want to use an Audio-Technica AT2020 condenser mic on the guitar and a Shure SM58 on the vocal. I am guessing that when I switch on phantom power because the AT2020 requires it that it will also turn on phantom power across all XLR inputs? Will this damage the Shure SM58?
    read more...
    0 95
  • DanielSan85
    Contributor - Level 1
    2020-06-09

    Hola!

    ¿cómo hago para registrar los equipos behringer que adquirí hace poco?

    Gracias

    0 36
Go to page