Statistics

250,905 members
128,124 posts
  • New
    MarkyMarkG
    Newcomer - Level 2
    2021-09-11

    Hi Folks,

    We currently have a pair of IQ12's for FOH and IQ18B's for Subs. 

    We have a pair of SD8's and the Behringer Wing.

    Is it possible to run the IQs via ultranet to the stage boxes?

     

    Thanks,

    Mark

    read more...
    0 26
    • MarkyMarkG
      GaryHiggins Yes the ultranet from the SD8's will be what is assigned by the Wing for aes50 ch's 33-48. So if your SD8 is on say Wing port A, the ultranet ports on the SD will carry what the Wing has assigned for aes50a out 33-48. Rout your appropriate sources there in the Wing and setup the speakers as per usual.
      • Sep 11
  • New
    binghamfox
    Newcomer - Level 1
    2021-09-10

    HI

    Got an issue with X18 (purchased recently) where Bus1 used for in ear monitoring output is only sending left panned signal.

    Yet all settings for channels and Bus 1 appear to be panned centrally ?

    0 9
    • binghamfox
      john0121 Hi, can you fill out the tech support form via the support button at the top of the page and attach a copy of your scene file with it. We can take a look then what the problem is. Thanks
      • Sep 10
      • X18 XAir - Bus output is panned left,
        binghamfox where do i find the scene file ? its on an android tablet
        • Sep 10
      • X18 XAir - Bus output is panned left,
        binghamfox no worries - found it !
        • Sep 10
      • X18 XAir - Bus output is panned left,
        binghamfox raised ticket CAS-486054-D6V2V0
        • Sep 10
    • binghamfox
      Paul_Vannatto Select the bus 1 master fader and adjust the pan from hard left to center. Also check to make sure it is not stereo linked to bus 2.
      • Sep 10
  • New
    KenChampaign
    Contributor - Level 2
    2021-09-09

    I have no problem playing it back on the  Wing  but I want to save the 16 track mix for later use in my DAW  Logic Pro X. I need to use the SD cards for another show in a few days. I'm sure it's just a routing issue. . . .  always is with my wing. 

    read more...
    0 11
  • New
    SilayanLidstromZenaida
    Newcomer - Level 1
    2021-09-09

    I am 72 yr old bought Audio mixer for my live streaming  but i have difficulty connecting it to my V8, laptop and mobile phone.  

    Tried many times to no avail.  Would appreciate much if somebody could lend me a helping hand.  need to buy some necessary cables or jack to be able to have this XENYX 1202FX Audio mixer work

    read more...
    0 12
    • SilayanLidstromZenaida
      Dale_M Hi there, we would advise raising a technical ticket from the support tab above so one of the team can assist you.
      • Sep 11
  • New
    IvanRosaMarcano
    Newcomer - Level 1
    2021-09-08

    Necesito a alguien que me venda el power supply soy de Puerto Rico

    0 8
    • IvanRosaMarcano
      KyleJohnson Hello, Kyle here with Music Tribe. For spare parts help please visit our Support page and submit a Spare Parts ticket.
      • Sep 8
  • New
    SYNTHUAXED
    Newcomer - Level 1
    2021-09-07

    When I load a file into X32 Edit from my laptop, it'd be very helpful if the file name was displayed somewhere in the app - perhaps in the title bar, such as most other apps do.

    No idea how to suggest that to Behringer, but if the idea resonates with anyone who can do so, I'd appreciate it.

    read more...
    0 10
    • SYNTHUAXED
      Paul_Vannatto If X32-Edit is connected to the X32, when you load a scene, the scene number and name will display on the right side, just above the Undo and Go buttons. The app's title bar shows the console's name and IP address
      • Sep 7
  • New
    DDTCo
    Newcomer - Level 1
    2021-09-07

    I recently purchased an XR18 for use with connecting to some wireless mics for a live theatre production. My goal is to trigger snapshots on the XR18 from QLab. While I can connect using XAir Edit through Ethernet and WiFi, I cannot connect using OSC. I was able to trigger the presets using a USB MIDI connection but since my QLab computer will be in the booth and the mixer will be offstage, I need the Ethernet connection. I also downloaded the X-Air Live Toolbox app and cannot get that to “see” the mixer either. Any suggestions you can offer will be appreciated. Thx! 

     
    read more...
    0 25
    • DDTCo
      Paul_Vannatto Are X-Air Edit, Live Toolbox and QLabs all on the same laptop, yet just X-Air Edit can connect? That is odd. For Live Toolbox, make sure the port is 10024 and select the Search checkbox and try a few times.
      • Sep 7
    • DDTCo
      cooperman20 Anyone run a tutorial on the Compact 32 desk. We are about to loose our sound engineer so I have to take over
      • Sep 8
    • DDTCo
      Paul_Vannatto cooperman20, this thread is about an XR18 connection problem with QLab and Live Toolbox, not about an X32 Compact. Please delete your post and start your own thread. Also search YouTube for X32, since there are tons of tutorials there.
      • Sep 8
    • DDTCo
      Paul_Vannatto DDTCo I sent you a PM
      • Sep 8
  • New
    RamoneartVonChusTone
    Newcomer - Level 1
    2021-09-07

    Hello.

     

    I need a crossfader replacement for DX500, a shop send me a CFM-1 but it's is small for my mixer.

    The original part is CFX1000 but i can't find any information about it.

    0 10
    • RamoneartVonChusTone
      KyleJohnson Hello, Kyle here with Music Tribe. Please visit our Support page and submit a Spare Parts ticket.
      • Sep 7
  • New
    yosbelim82
    Newcomer - Level 1
    2021-09-07

    Hello there does any one know what is going on with X32 Rack can't find it any where

    1 13
    • yosbelim82
      Paul_Vannatto Like everything electronic, automotive, etc., it's probably due to the global chip shortage.
      • Sep 6
    • yosbelim82
      Dale_M As Paul states there is a world shortage of semi-conductors at present, however if you go to the Behringer website and select the BUY tab it will give numerous places you can buy so may be worth double checking with the retailers. https://www.behringer.com/buy.html
      • Sep 6
  • JohnnyChandler
    Contributor - Level 3
    2021-09-06

    Does anyone know what the slope of the high and low cuts on the main mixes are? Coming from an X32 where I had them set as LR24 filters for the LR and Mono crossover.

    0 5
    • JohnnyChandler
      Paul_Vannatto Hey Johnny, if you turn on the low band, then select the Settings, then the low band pull-down list and switch between cut and LR24, you will find they are identical.
      • Sep 6
Go to page