I just recently tried to record from my M32R for the first time, but my laptop only recognized the first 8 channels, not all 32 (I have 32 in/32 out selected on the console settings). I have the most recent driver for it downloaded and installed, but I am running Windows 11, which I think is the problem. I looked in the update history doc that came with the download, and it said nothing about support for Windows 11.

I just want to make sure I'm not overlooking anything. And, if Windows 11 is the issue, does anyone know when they might release an update that supports it?

Thanks yall

Hi,  This might be a silly question but what are the odds that some kind of firmware update will be released to enable multi track recording in the MR12?  I like how I can record a mixed stereo file , but it'd be great if discreet tracks could be captured like the Tascam Model 12.  

Any chance or no dice?

We have an older Behringer X32 Rack Mixer with a USB Interface Card.  This card works fine with the older original X-UF USB Driver Version 6.13 downloaded to my Windows 10 based Lenovo Laptop in both Input/Output directions.  If I try to load this older driver onto a Legion Windows 11 Laptop (Containing our Internet Streaming Software), it will get caught in a loop during the install ("Plug in USB cable and Power up the Mixer") and not finalize.  If I try the two newer USB Drivers (X-USB Audio Driver Versions 4.59 or 5.12.0) downloaded from Behringer's Website to Windows 11, the audio level is fine from the Laptop output to the Behringer Mixer.  However, audio level from the Behringer mixer to the Laptop is very low (Only 1-2% volume with everything maxed out.)  I have not yet tried the two newer drivers on my Windows 10 computer but expect that they will work OK.  We are only 1 level back on X32 Firmware (4.05) noticing that a new revision has recently become available. (4.06) Release notes say nothing about this problem nor have anything to do with how we are using with our mixer.

We have been using a Ham Radio version (Signalink USB) of the more widely known Focusrite USB Interface which has been working great for the past 22 months of the pandemic.  That external USB Interface works great with both Windows 10 and 11 and has protected us from Ground loop issues when the streaming laptop was being operated a fair distance away from the mixer.  

It looks like we either need an updated driver for Windows 11 if Behringer can provide this or we may need to backlevel our Internet Streaming computer to Windows 10 to get around this problem.  We are trying to eliminate the external XLR cables, Signalink, etc. as our streaming laptop is now local to the X32 Rack cabinet. (Run by Remote Desktop over WiFi)

Has anyone else had issues with Windows 11 relative to these Behringer X32 Rack USB Audio drivers?

Hi

I've plugged in a c414 mic into the front and splitting the signal to FOH and monitors. The direct out is plugged into the FOH board and the monitors on the link. However, phantom power is not going from the FOH board to the mic. 

Is the ms8000 faulty or am I doing something wrong?

Suddenly I can't get a connection between the X32 compact and the S16.

The display Port A flashes from time to time, but there is no signal, neither in nor out.

I performed a factory reset .....

But in the routing the display shows Port A: no device

Sample rate: 48 kHz on both devices, 44.1 kHz on both devices.

Nothing brings anything.
what should I do, Garntie has already expired

Do you have a tip?

Does anyone know where i can test my 2nd hand 2015 Midas DL371 Audio System Engine?

I brought it 2nd hand but dont yet have a PRO6 Controller and want to test it asap. No error lights come up but i still have no clue it actualy works. 

Any advice where i could get it checke over or tested?

Thanks

There are several projects I am planning to use the DM8000 or DM8500 for, but trying to find pragramming information is extremely challenging.  Before I spend that much money, I would like to have an idea that it will work and do what I want it to do.  I found the DM8000 manual which was helpful, and the Designer software has some limited help built in, but I have no idea how KONTROL interfaces with designer or how to program/use the touch screen on the DM TCE

Thanks in advance for your help!