Hi,
I have a Midas 32R that I'm demoing at a house of worship that is transitioning from a board that has 1/4" outputs. I did not have enough 1/4" female to XLR female adapters so I decided to use the AUX Outputs on the Midas to set up the monitor mixes. I patched MixBus 1-5 respectively to each of the Aux Outputs 1-5 and set the tap point to PreFader + M. I can control the individual channel volume in the mix, however, I cannot control the overall mix volume. Is there are setting that I am missing?
Thanks. I factory reset the mixer. The issue was due to the tap point for the MixBus. The factory reset set the tap point for the MixBus to Post Fader. I now have Master control over the mix.
Does anyone know if there is currently a training course for the m32, I currently run one thru a few production companies but feel i could improve my navigation around the console as well as patching capabilities.
We would like to connect a pair of stage boxes to the M32 in a house of worship. Ideally it would be one DL32 and one DL16.
My intention is to have the DL32 backstage to handle all of our FOH outputs as well as our stage monitors and IEMs, plus the inputs from wireless mic receivers also installed backstage. The DL16 would be on the stage to handle inputs from drums and other instruments, plus utilize the Ultranet connection for personal monitor mixers. The stage boxes would have a connection to the M32's AES50 A & B jacks. Are there any limitations on this setup, such as total usable inputs/outputs? Are there any benefits or down-sides to connecting each to a different AES50 bus?
Hello!
Does anyone here have the OSC control documentation for the midas pro series? I'm working on integrating them into companion, but I'm having trouble digging up good references on their protocol.
Hello, I'm a customer from Romania and I want to buy an Midas M32 Live console but I can't find any. Can you give me an approximate date when the console will be available to purchase in Europe? Thank you!
Hello,
appreciate our input on following Need and Idea about using 2x Midas HUB4 for connecting 41 channels and 8x stereo IEM
41 channels on stage, 8 person band, 2xDL16, 1x DL32.
Need:
8x stereo wireless IEM from stage, IEM mix by musician's app and FOH engineer
Idea:
3x DL stageboxes connected with AES50 to Midas HUB4, 4x2 analog out (from HUB4) to 4x IEM transmitters
Second midas HUB4 daisy chained over AES50 with first Midas HUB4, 4x2 analog out (from HUB4) to 4x IEM transmitters
AES50 frome second Midas HUB4 to FOH: Behringer Wing
Questions:
Can Midas HUB4 be daisy chained? or do I need 2x AES50 from FOH?
Can this idea technically be done?
Are there better/other ways of implementing "need"?
See attached simple scetch of the set-up in mind
Thank you, Arie
Final question (I hope ;-) ) Can the Hub4 be used without DP48? So simply in a side rack on stage to make the connection with Wireless IEM transmitters, and the IEM mix be done by the FOH (Behringer Wing). According to the documentation, I think: yes but there is some ambiguous tekst that makes me doubt. Thanks!
Bonjour,
Ma table Midas X32 LIVE n'est plus reconnue par mon Mac. J'ai l'habitude de faire des enregistrements dessus avec la cable USB et tout d'un coup la table n'est plus visible par le Mac (il n'y rien qui apparaît lorsque je branche le cable USB). J'ai déjà changé d'ordinateur, de cable USB etc... mais rien ne change.
Pourtant l'enregistrement avec les cartes SD marchent nickel.
Merci!
Hola, me gustaria ir a realizar la certificacion de midas pro como lo puedo hacer?
Having issues connecting my router and iPad to m32r and can't connect to iPad it keeps saying listening and never connects