Statistics

240,862 members
117,081 posts
  • New
    Ahltech
    Newcomer - Level 1
    2021-06-05

    I've done this over 100 x. 

    cat 5 shield cable 75'. Tests fine 

     

    tried 2 other cables. 

    on routing dl1-16 shows up. 

    On mixer solid red light on screen. Blink red light on dl-16

     

    tried several cables....and A& B side.... same results 

    read more...
    0 21
    • Ahltech
      Paul_Vannatto Make sure the AES50 cable is connected to the A port of the DL16.
      • Jun 5
    • Ahltech
      Ahltech

      It is on the a side

      • Jun 5
    • Ahltech
      Ahltech

      It is on the a side

      • Jun 5
    • Ahltech
      Paul_Vannatto What mode is the DL16 set to? If the SN Master light is lit, that means that it is set to be the master clock along with the M32. Change the mode so that only the M32 is the master clock.
      • Jun 5
  • New
    Markbaker
    Newcomer - Level 1
    2021-06-05

    The Behringer XR18 Digital Mixer Handbook is finally complete and available. 

    it is applicable to the Behringer XR16, XR18, and MIDAS MR16, MR18.  

    More details here

    Avaikable from Amazon - worldwide. 

    read more...
    2 34
  • New
    teejayvee
    Newcomer - Level 1
    2021-06-04

    Hello.

     

    Does anyone actually know when the M32C will become available again? 

     

    Thanks!

     

    ~Tom

    0 32
  • New
    djexit
    Newcomer - Level 1
    2021-06-04

    Hi everyone, I need some guidance.

    I work for a church that is buying a broadcast van for live streaming of services. They want to use MADI to feed the truck the inputs.

    Gear

    S32 , M32 Monitor Console (Fed from S32 AES50-A), P16's (fed from Mon), FOH Console (Fed from Mon via AES50-b port)

     

    The main hub of the set-up is the Monitor console as it takes the 24 inputs from the S32 via AES50-A and shares it with the FOH console via AES50-B. I also have P16's being fed from the MON console via AES50-A. I also have 6 LOCAL inputs into the FOH console.

     

    How do I get all inputs (24 from stage + 6 local FOH inputs) to a broadcast van VIA MADI? I know I will need a madi card, I'm assuming it will just be in the MON console as thats the central I/O for the set-up

    Both Monitor/Foh consoles are physcially close to eachother so it is possible to plug in those 6 FOH inputs into the Mon console but I'd have to patch them back to the FOH console.

    I'm not sure if all the spliting and virtual patching is possible.

    Please advise. 

     

     

    read more...
    0 27
    • djexit
      Paul_Vannatto Yes it can be done. I would suggest that you install the Madi card into the FOH console, since the routing is much simpler to the Madi card. On the Routing, Card screen assign AES50 B1-8, 9-16, 17-24 to the first 3 banks of 8 and Local 1-8 for the 4th bank of 8 (assuming you are using the first 6 Local inputs).
      • Jun 4
  • New
    knaepp
    Newcomer - Level 1
    2021-06-02

    To whom it may concern,

    we are currently working in three different environments. First rehearsalroom has an x32 Producer with two S16 connected, second environment is our studio with M32R and two DL16 connected and a third environment with a M32C (pretty new) and one or two DL16 connected for smaller events or accoustic sets. We use cues, scenes and snippets widely to control the key settings of our Mixers and the effects used during a gig.

    Now I recognized that it is a problem to name the cues on our M32c. Each time when we load a cue-sheet from usb-drive and do some modifications using M32-Edit Software (macOS) the Name of the cue will be automatically adjusted to

     

    M32C_YYYY-MM-DD_HHhmm.nnn.<snc|snp|shw>

     

    The internal name of the cue will be changed to M32C even when we change the name using M32-Edit. Our name will allways be ovwerwritten during the next export of the show.

    Naming of the show is important to us because we document our adustments and create shownames containing serial numbers to  be able to fall back to older "releases" of our cofiguration if necessary. Each time when using M32C we have to do this manually. This means renaming all files and adusting the internal name of the show using

    sed -i 's/M32C/<nameOftheShow>-<serialNumber>/g' <nameOfTheshowfile>.shw

    Do you know any workarounds for this - let me call it a feature?

    Best regards

    Matthias

    read more...
    0 37
    • knaepp
      Paul_Vannatto Hi Matthias, before exporting the show from the M32C (or any M32/X32 for that matter), make sure to name the show (bottom right corner of the Cues screen in M32-Edit). If that is left blank, then the console will use a generic filename (and show name in the first line of the .shw file).

      As an alternative, have you tried the Show Manager app that I have developed?
      https://sourceforge.net/projects/m32x32showmanager/
      It provides an alternative GUI to create and modify shows.
      • Jun 2
    • knaepp
      knaepp Hi Paul,

      thank you for your answer. That was the way we already tried it. We set the name of the show in the bottom right corner. The export the usb stick is only possible on the M32C edit using the "one knob". After choosing "Export Show" the name of the show will be M32C...something -like I told you before. There is no option to do this via M32-Edit. The name of the showfile will always be adusted and the name of the show is M32c.
      I know your showmanager, thank you for sharing it. Most members of our band are not familar with tools like this (some of them even do not really understand the show-concept).
      My expectation is that a stored name would not be adjusted by the console.

      BTW: we use firmware 4.06 and M32-Eit 4.3
      Best regards

      Matthias
      • Jun 2
    • knaepp
      Paul_Vannatto Thanks Matthias for your response. Until just recently, the M32C and X32 Core had issues exporting anything and that was fixed as part of one of the firmware updates. Evidently this is a bug. I will pass it on to the developers. In the meantime I would suggest you make the necessary changes using the M32C and export the affected scenes and/or snippets (either using the Export to USB stick) or using the dual nature of M32-Edit, then merge these scenes/snippets into the current show using either M32-Edit or Show Manager.
      • Jun 2
    • knaepp
      knaepp Hi Paul,
      I just checked again showmanager. May be we have a misunderstanding. We do not use the showfile from usb-stick, we always import the entire show to our consoles. Changes from one scene/show/snippet to the next will be done using midi. Because of that all changes will be done affecting the scenes and snippet files on the console.
      After finishing a gig or rehearsal we - again -export the show to the usb stick. This export destroys the name of the show and the name of all files - even when we set the show-name using M32-Edit.

      I hope this was not too confusing.

      Greets
      Matthias
      • Jun 2
    • knaepp
      knaepp

      Hey Paul,
      thank you. Until we see an upcoming future update we will use the current way (rename files and change showname using sed)

      Thanks for your help and stay all healthy

      Matthias

      • Jun 2
  • New
    Gordimus
    Newcomer - Level 2
    2021-05-27

    I am trying to use my M32 for FOH and going to DL32 Port A and Port B of DL32 to Port A on X32 for monitors. I can't get local outputs to work on the X32. 

    0 41
    • Gordimus
      Paul_Vannatto If you mean by "local outputs" as the XLR outputs on the back of the X32, you would assign those (in banks of 4) on the Routing, XLR Out screen.
      • May 27
    • Gordimus
      Gordimus

      Thanks. I think I tried that already but I will retry today.

      • May 27
    • Gordimus
      Paul_Vannatto What did you assign to those banks of 4?
      • May 27
    • Gordimus
      Gordimus

      I don’t have the console in front of me. Can you tell me how I should assign them to outputs on back of X32!

      • May 27
    • Gordimus
      Paul_Vannatto Typically the individual outputs are assigned on the Routing, Outputs 1-16, such as the buses 1-8, etc. Then those banks of 4 are assigned to the XLR Out (eg. Outputs 1-4 -> Out 1-4, Outputs 5-8 -> Out 5-8, etc.)
      • May 27
  • New
    kellned52
    Newcomer - Level 1
    2021-05-26

    I have a audio libary (wave-files 44.1 kHz) on a 8-GB-Usb-Stick (fat32-format). It works well for playback at MR12. then I make a copy 1 to 1 on a 16-GB-Stick (fat32-format). It works well on a WIN10 or Linux-Computer, but on the MR12 I here distorted sound (nearly 1 octav higher and double speed, with interrupts). The directory and meta-datas are shown normaly. The same Problem I have for more than one stick.
    If I copy the files back to an 8-GB-Stick, this stick works well.
    the Firmware and MAir-Edit are actual.

    Is 8GB a limit or do I need a special formating for sticks greater then 8 GB?

    best regards
    Dieter

    read more...
    0 48
    • kellned52
      DavidKnighton Hello kellned52,
      I would suggest you don't copy from stick to stick. Make a master playlist on your computer and then copy the master playlist to each thumb drive individually. Format is FAT32 for all sticks, regardless of capacity. Also, try performing a long format rather than a quick format. Obviously it will take much longer to format use the long format option, but it will ensure all the 1s and 0s are deleted from the previous format. A quick format doesn't quite delete all the 1s and 0s, and is usually ok in most scenarios, but when in doubt, wait it out.
      • May 26
    • kellned52
      kellned52

      Thanks David
      for the answer. I will reformat a stick (no quick format). Then I will copy some songs from the computer file by file to the stick. After the test on the MR12, I'll get back to you. This can take a while as the MR12 is being used at a different location.
      Best regards
      Dieter

      • May 27
    • kellned52
      kellned52

      Unfortunately, the procedure described was unsuccessful. Reformatting the stick to block size 4096 analogous to the 8GB stick also had no effect.
      If of interest:
      SanDisk Ultra-Fit ESD-USB 3.0; 16 GB

      Best regards
      Dieter

      • May 27
    • kellned52
      KevinMaxwell it sounds like your WAV files and you clock on yourMR12 are not set to the same clock rate. One of them is set to 48k instead of 44.1k
      • May 31
    • kellned52
      kellned52

      @Kevin: That is not the problem. Both sample rates are at 44.1 kHz

      • Jun 1
      • Distorted sound,  if I use 16-GB-USB-Stick
        KevinMaxwell Have you tried a file comparison utility? Compare the same file on the 2 devices and see if they are really the same.
        • Jun 1
  • New
    MarkNorgren
    Contributor - Level 3
    2021-05-25

    Just wondering about the stability of the latest Firmware for the M32R and the DL32.  I am heading into the gigs for the summer in June and would like to know if there are any bugs in the latest Firmweare releases.  We have rehearsed a few times with no problems, but I only use about half the input/outputs we do once we get out.  My setup has been flawless for years and expect the same.  Please let me know your experiences for those of you already out and about!  TIA

    read more...
    0 43
    • MarkNorgren
      Paul_Vannatto Firmware 4.06 seems to be very stable here and I'm not aware of any major bugs being reported. That said, I also haven't been able to use the X32 for over a year, due to the pandemic lockdown. I'm doing sound for an outdoor wedding this weekend, but will be using the Wing, simply because I haven't had an opportunity to use it for a live event yet.
      • May 25
      • M32R and DL32 Ready to Gig!
        MarkNorgren Thanks Paul! My hope is all is well. No news, is good news!
        • 1
        • ·
        • May 26
  • New
    Midas76
    Newcomer - Level 1
    2021-05-25

    Hello, I am looking for the part number for bus send encoders for the Midas M32. Something got dropped on the encoder knobs and I would like to get a replacement. They still work but when turned they spin funky.  If I need to replace the whole section that would be great too. Can anyone tell me if these are available and price? Thank you

    read more...
    0 44
    • Midas76
      WilliamR Hello, William from musictribe here. If you could click on the support link above and open a parts ticket, someone can get the process started for you asap.
      • May 26
  • New
    vvish
    Newcomer - Level 2
    2021-05-25

    Hi Everyone, about HD96-24, I would like to express my recent views. After I upgraded to the latest 1.15.0 version, I think the New PIE effect is so cool and very useful. Then, I now have a few questions.

    1. When will the "auto-mixer" function be launched? We are so looking forward to it.
    2. Will GEQ consider the way of "on fader" operation in the future?
    3. How to use the 9 Tap Tempo correctly?
    4. After selecting the channel, in the Send Overview mode in the right column, when the assignable knob is used for adjustment, the value of the send volume cannot be displayed.

    Thanks.
    Regarding the future development of HD96-24, we are always positive.

    read more...
    0 44
    • vvish
      Dale_M

      Many thanks for your inquiry, can I please ask that you submit the above via the support tab/Pre Sales as the team in question are not on Community. In the subject line please add FAO Dale Minaker so I can pick this up for you

      • May 26
Go to page