Statistics

223,462 members
97,656 posts

Sort

Sort

Discover

  • New
    JohnMathew
    Newcomer - Level 1
    2021-01-05
    Registering my new Behringer product | Active DI Boxes

    I have been trying to register my Behringer V-Tone Bass Driver DI BD121 with this site as recommended on the product instruction pamplet.

    Done evrything required here but dont see how to register my product. HELP ????

    0 29
    0
    Mark As Solved 0 Reopen Discussion 0
    • 1 Replies
      Oldest
    • JohnMathew
      Nigel67 Hi John, sorry about the issues that you are experiencing registering your product. Can you tell me how far into the process you get before you receive the error message or are unable to get any further. Can I just confirm that you are going to the support tab at the top of this page and then on the new page that opens, scrolling down and clicking on the tab Product Registration. Let me know where the process falls over and I will help you further. many thanks
      • Jan 4
  • New
    belfie13
    Newcomer - Level 1
    2020-12-31
    DI4000 and MF350 Emulated Line Out | Active DI Boxes

    I've heard alot about the issues with Marshalls Mode Four MF350, where something to do with grounding destroys the amp..

    i'm not sure technically what this means but I want to know if this has anything to do with the ground lift and do i use it or not. is there any other issues with using the MF350 Emulated Line Out through the DI4000 to my mixing desk?

     

    specs. i think are relevant?

    MF350 Emulated Line out:

    level: -10dBV | recommends connecting to inputs of impedance >20㏀

     

    PreSonus StudioLive 16.4.2

    Line Inputs:-

    Input Impedance: 10 kΩ
    Maximum Input level (unity gain): +22 dBu

     

    read more...
    0 22
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    wojtashek
    Newcomer - Level 1
    2020-12-02
    Behringer DI100 Ultra-DI Active DI Box | Active DI Boxes

    I need connect mixer through Radial Catapult to another mixer nd connect to mic input. According to Radial Engeeniring I as I use RX4M as output all signal should be Mic Level.

    Is this DI Box Behringer DI100 Ultra-DI will transform Line Level Signal from mixer to Mic Level (as attenuation is +48dBu)? If not would you recomend abother one?

    read more...
    0 30
    0
    Mark As Solved 0 Reopen Discussion 0
    • 2 Replies
      Oldest
    • wojtashek
      Paul_Vannatto Hi Wojciech, the DI100 will change the line level input signal to mic level. The issue might be powering the DI100. Phantom power can be applied to the XLR-M output, but not to the XLR-F input. That would mean that the phantom would have to come from the second mixer via the Catapult. The question is whether Radial's design allows phantom to pass through the Catapult. If it doesn't, the other solution is a 9V battery (not ideal).

      An alternative option would be the Behringer Shark FBQ100. It uses a separate power supply and can be configured for line input and mic output (see page 5 in the manual).
      • December 2, 2020
    • wojtashek
      wojtashek Thank you for your help. Phantom power is coming through Radial Catapult TX4 where is connect FOH mixer. Thus should supply the power to DI Box. If not I will take your advise Thank you
      • December 2, 2020
  • New
    SeriusNtentions
    Newcomer - Level 1
    2020-11-26
    Reamping using a Behringer Ultra DI 100 in Reverse? | Active DI Boxes

    Hello Folks,

    Has anyone tried Reamping with a DI Box by using it in Reverse?

    1. You take a 1/4" balanced TRS cable out from any output of the UR-44 and insert it into rear panel of your DI Box Output via an XLR Female to 1/4" female. (Mine is a Behringer DI-100.
    2. Then on the Front of the DI Box connect a 1/4" TRS balanced cable from the Input to the input of the first pedal in the pedal chain.
    3. Then a TS unbalanced cable from output of the last pedal in your pedal chain into a Hi-Z input on the UR-44 (1 or 2) ?

    https://mediadl.musictribe.com/media/PLM/data//images/products/P0062/515Wx515H/DI100_P0062_Other1_B.png
    https://mediadl.musictribe.com/media/PLM/data//images/products/P0062/515Wx515H/DI100_P0062_Other1_B.png
    https://mediadl.musictribe.com/media/sys_master/h4c/h48/8850060607518.pdf

    read more...
    0 37
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    KennyBarnes
    Contributor - Level 1
    2020-11-14
    Ultragain ada8200 CDSA? | Active DI Boxes

    Hi, will the 8200 accept a digital input from a Sony CDSA player and divide it into 5.1 analogue outputs please? 

    0 18
    0
    Mark As Solved 0 Reopen Discussion 0
    • 1 Replies
      Oldest
    • KennyBarnes
      Paul_Vannatto Hi Kenny, the ADA8200 digital input is an 8 channel ADAT and can output to the 8 output channels. Does the Sony player output this digital signal?
      • November 14, 2020
  • Behringer
    Triber Moderator
    2020-10-19
    New Product Release: ULTRA-DI PRO DI4800A | Active DI Boxes

    ULTRA-DI PRO DI4800A
    http://bit.ly/Behringer-DI4800A

    Gives you first-class DI channels in a single rack space. Each channel is equipped with one input (XLR or ¼” TRS) and two XLR Outputs at the front and back to connect to your amp or monitor console allowing for 8 outputs in all.

    #Behringer #DI4800A #Active #DIBox #DirectInjection #Booster #LineIsolator

    read more...
    1 97
    0
    Mark As Solved 0 Reopen Discussion 0
  • markmojo62
    Newcomer - Level 1
    2020-07-08
    BDI21 Replacement knobs | Active DI Boxes
    Hi, is it possible to get a set of replacement control knobs for the BDI21?
    0 56
    0
    Mark As Solved 0 Reopen Discussion 0
    • 1 Replies
      Oldest
    • markmojo62
      WilliamR Hello, Please create a care ticket in the support link above and we can help you out with that.
      • July 8, 2020