Statistics

259,802 members
138,220 posts
  • mochiji
    Contributor - Level 2
    2020-02-21

    Could you let me know is there DM KONTROL and DM801 manuals?
    The DM KONTROL have help. However, nothing happens when I click the contents tab in help.
    Also, I can't find a place to download the manual.
    Already descontinure this product or company will bankrupt?





    read more...
    0 271
  • jankoppe1
    Contributor - Level 3
    2020-01-01

    Hi there.

    Was just using the DN9650+KTDANTE64 for the first time in conjunction with a Behringer Wing to bridge it into a Dante network.

    Just a simple question, as I find it a bit confusing: I noticed that from each AES50 cable only the first 24 channels have been mapped to Dante. I did route additional channels on the Wing on the first AES50 output, but they just did not arrive in Dante. I could not find any "routing" or "patch" menu that would change this behaviour. System was running at 48 kHz all the way.

    Is this just a hard limitation of the KTDANTE64, or some weird behaviour with the new Wing? Did I miss some option to change that behaviour? Having to use two AES50 ports for the amount of channels that a single AES50 port could handle worked this time as we only had a DL32 attached on the console, thus, two free ports available. In the future I will definitely add a Dante AoIP module to my personal Wing though.

    read more...
    0 376
    • jankoppe1
      Roblof

      If you only get 24 channels then this suggests that the dn9650 operates at 96k.


       


      Are you using the dn9650 as the master clock and set to 48k. If not, then it is my understanding that it will up-sample to 96k.

      • January 2, 2020
    • jankoppe1
      jankoppe1

      Nope, all settings were at 48K, the AES clock was the master clock (coming from the wing, running at 48K).

      • January 3, 2020
    • jankoppe1
      colino_ltapl

      Hey,


      I am not sure if the KT9650 is natively 96k, but what i can do is i will check if 9652 is able to do this solution. 


      Meaning to say AES50 card and Dante card on 9652. 


      I am waiting for my AES50 card to arrive and i will try this out if it works ok? 


      Hope to share more and learn more with you guys. 


      Cheers! 


       

      • May 8, 2020
  • mody1
    Contributor - Level 1
    2019-12-28

    Hello

     was wondering how to get this option and how mutch it cost ?

    0 114
  • tommypenngotti
    Contributor - Level 2
    2019-12-26

    Hello - I just purchased a Klark Teknik DN350 EQ that looks to be from the middle 80s where the 120V fuse holder(plug) is missing and there is just a hole on the back board ...there are fuses on the inside under hood. The seller is claiming just the "plug blank" is missing... although it does possibly look modified?? Any help on this appreciated . Thanks 

    read more...
    0 155
  • NASservice
    Contributor - Level 1
    2019-10-08

    Hi all,

    We have forgotten the password for one of our DM8000's, is there any way to do a hard reset or recover the credentials somehow?

    1 496
    • NASservice
      Distinctap

      Following ?

      • October 8, 2019
    • NASservice
      DavidBradshaw

      There is a way to access a locked DM8000- I'll contact your guys directly to share.

      • November 27, 2019
    • NASservice
      todd_lewis

      David,


      I am not able to connect to the DM8000 at all. Can you contact me?

      • May 18, 2020
    • NASservice
      RexBeckett


      @todd_lewis wrote:


      David,


      I am not able to connect to the DM8000 at all. Can you contact me?





      @todd_lewis 


      Hello Todd, welcome to the community.


       


      Your post may not be noticed by anybody who can help. I suggest that you raise a Care ticket for Technical Support explaining your problem. This is done by clicking on Support at the top of the page and then clicking the Create a Care Ticket button. This is only possible if you have completed all the required fields in your profile. Make sure that you fill-in every required field on the Care form.

      • May 18, 2020
    • NASservice
      todd_lewis

      Thanks. I finally got connected to the box. However, it has a very old version of firmware on it. I need v1.5 of the DM software. Does anyone happen to have that file?

      • May 18, 2020
  • petermciver
    Contributor - Level 1
    2019-08-19

    Hello-

    I’m using a DM8000 for a DSP Control in a theater install.  I have a fleet to f turbosound speakers all fed audio over Ultranet.  I plan on coming off a X32 into the DM8000 and then out to a P16D.  The fire alarm company has installed a smart relay with a set of N/C contacts that open in an active alarm state.  I’d like to use the GPIO terminals to trigger a ganged mute for all of the ultranet channels.  

    Heres where I need some help.  I’m not sure of all the settings and the wiring terminals that I need to connect to make it work.

    I submitted a trouble ticket weeks ago and never heard back from Klark Teknik.  Anyone have suggestions?

    read more...
    0 455
    • petermciver
      Paul_Vannatto

      Hi Peter @petermciver,


      Welcome to the forum. I'm not experienced with DM8000 so I had a look at the manual. From what I can see, the GPIO can only control volume (page 55). In order to externally control mutes or gang mutes, it needs to be done via RS232 (page 43). One way to create an RS232 interface with GPIO (connected to the smart relay) is with an arduino or Raspberry Pi and an RS232 shield.


       

      • August 19, 2019
    • petermciver
      DavidBradshaw

      Hi Peter


      You can connect a NC/NO contact to any of the GPIO pins. In DM Designer add a 'GPIO Select' object to the design and nominate that to be connected to whichever GPIO pin you physically connect the NC/NO contact to. In DM Designer add a ganged mute to cover all the outputs and in parameters check the box to add a 'control input'. In DM Designer, connect the last output pin on the GPIO select for NC to the control input on the ganged mute. Load up the design and you are done. 

      • November 26, 2019
  • DavidBradshaw
    Solution Leader
    2019-06-06

    Klark Teknik DM DESIGNER 3.1 and DM KONTROL 3.1 are now available for download, via the downloads section on the DM8000 product page.

    DM KONTROL offers PC based customised control page creation and operation of a DM8000 DSP across an ethernet network, when deployed with the new DM801 serial to ethernet bridge.

    Check the downloads here:

    https://www.klarkteknik.com//Categories/Klarkteknik/Signal-Processors/Matrix/DM8000/p/P0B17/Downloads#googtrans(en|en)

    read more...
    1 489
  • Emadson
    Triber Contributor
    2019-05-29

    DM8000 Design 2.9.1 Software and Firmware available for download

    DM8000 Software and Firmware Downloads

    read more...
    0 447
Go to page