Statistics

229,577 members
104,644 posts
  • AlanLotra
    Newcomer - Level 1
    2020-09-25

    Any reason why the T2 is no longer available in the toneprint app ?

    0 34
    • AlanLotra
      WilliamR Hello Alan, The T2 reverb uses the Algorithms from the Hall of fame reverb. So any nonartist Hall Of Fame reverb template can be used as a starting point for creating your own tone prints.
      • September 25, 2020
  • Wreford
    Newcomer - Level 1
    2020-09-22

    I am not if this the correct area for this discussion but I have recently bought the TC electronics hall of fame 2 reverb pedal but there is no sound coming through at all. I was using a modular synth with sound out put through the pedal. The pedal peers on,  The red light comes on, the mash light comes on but no sound coming through. I have used other pedals the same way and these have worked fine. Is something I am missing with this particular pedal?

    read more...
    0 51
    • Wreford
      JasonB81 Hello John - If you have tried your other pedals with this same configuration and they work but your HOF2 does not - can you please click the support button above and create a support ticket? Someone from support will be able to follow up with you on the issue. Thank you for contacting us.
      • September 22, 2020
    • Wreford
      TC-Mike HI John, in general you need to attenuate your signal when going from your modular outputs to guitar pedals that is made to be operated at instrument level. the voltage of the audio signal that a modular synth outputs can be up to 10 times of line level (1vline level vs 10v modular) and pedals are just not able to handle this. When passing through filters and other modules the voltage lowers of course, but for trouble free operation and flexible integration of guitar pedals into your modular rig, you are well advised toconsider a module that handles level conversion for you (like an insert loop/amplifier moduler for guitar pedals) i can recommend the industrial electronics "black locust" module for flexibility as it has FX send /returns + dry/wet mix like on a mixer and supports 4 pedals. :-)
      https://www.thomann.de/gb/industrial_music_electronics_black_locust.htm
      There are also more cost effective solutions available from other manufacturers.
      • September 30, 2020
  • TCsucks1
    Newcomer - Level 1
    2020-08-30

    I just got the Flashback 2. I programmed and stored a TonePrint but have found that if I leave the TonePrint to use a different delay type, when I go back to my stored TonePrint the settings are off because it now responds to where the knobs are physically set based on tweaking I did on the other delay type.

    Hopefully I'm doing something wrong because I was under the impression that stored TonePrints were like presets in that, once selected, would recall ALL programmed settings regardless of where the knobs are physically set.

     

    read more...
    0 47
    • TCsucks1
      Nigel67 The potentiometer (knob) values are not part of the Toneprint. They are mapped, however the the current parameter value/position of the toneprint that you have loaded in is not. The position that the pots are set to is what they will operate at.
      • September 2, 2020
      • Flashback 2 TonePrint problem
        Gegatso I'm having basically the same issue. New Flashback 2, using a Mac, Catalina 10.15.7. I made and saved a toneprint at my computer. Went to the amp and plugged up. Played around with some settings while NOT on bank 3 where my toneprint was saved. I went to use my pattern and It was still playing the pattern set by the dials. Am I doing something wrong? It seems too easy, but sometimes simplicity is when the problems creep in. Remember that it is my first day with the pedal, but I followed every step and it all seemed to work. The software showed all my settings right where I had the knobs set for my perfect sound. Much thanks in advance!
        • November 8, 2020
  • keno
    Newcomer - Level 1
    2020-08-17

    hola amigos, queri preguntarles si existe el toneprint editor para pedales tc electronic antiguos, yo tengo un flashback delay de los primeros y no puedo descargar en mi mac con osx 10.9 maverik.

    alguien sabe de esto?.

    gracias

     

    read more...
    0 33
    • keno
      PedroRodrigues Hola Keno Lamentablemente no los tenemos disponibles porque los acuerdos de desarrollo de software para la tienda Apple y Google Play nos obligan a tener el software actualizado y eliminar los antiguos y solo hacer que el software esté disponible exclusivamente en estas plataformas.
      • August 17, 2020
    • keno
      keno ooo bueno entiendo, estoy un poco anticuado con mi sistema, agradezco la ayuda. saludos cordiales.
      • August 18, 2020
  • bironology
    Newcomer - Level 1
    2020-08-13

    I've recently acquired a second hand TC Flashback X4, and I did in fact read the product manual before posting.

    My issue is when using the looper function. Many times, but not always, I find that before the recorded loop begins again, there is a silent pause of maybe 250ms (I would have used the word "delay" but didn't want to confuse in this conext as I am not talking about the delay features at all).

    My instinct was to update the firmware, but I don't have a USB Mini-B cable and local stores don't stock those anymore so I'm waiting on an Amazon delivery. In the meantime, I'm wondering if this could be user error.

    Any clues?

    Thanks.

     

    read more...
    0 29
    • bironology
      PedroRodrigues Hi bironology I would suggest to please press the Play/Pause footswitch, the footswitch with the Play/Pause symbol, to access if that happens again.
      I would advise you to update the firmware for your unit, please follow the link below to access the manual where you will find the process on how to update and the firmware
      https://www.tcelectronic.com/tcelectronic/product?modelCode=P0CKU
      • August 14, 2020
  • AhmadAk
    Newcomer - Level 1
    2020-07-10
    Hey there! Can anyone help me to know what is the last update for tc electronic system 6000 the black one not MKII?
    0 49
    • AhmadAk
      WilliamR The MKII Upgrade is recommended for all SYSTEM 6000 users as software release 5 will be the last for the original platform. System 6000 software, including system upgrades and new algorithms will only apply to SYSTEM 6000 MKII moving forward
      • July 16, 2020
    • AhmadAk
      WilliamR https://www.tcelectronic.com/tcelectronic/product?modelCode=P0CJW
      • July 16, 2020
  • maceman
    Contributor - Level 2
    2020-07-08
    HI, I have had the first Flashback X4 for years on my pedalboard with a 300 mA, 9V connector (Voodoo pedal power), no problems. I dropped in the new Flashback2 X4 and it will not run properly. It sounds all crazy distorted and a hot mess. When I power the Flashback2 with the supplied 9V adapter it works well. So, what is the actual mA requirement for this Flashback2 X4? Is it more than the Gen1 X4? Is there something I'm missing here in my set-up? It seems odd that this pedal would now require more than the standard Voodoo would provide. Thanks.
    read more...
    0 37
    • maceman
      TC-Mike Allthough the Flashback 2 X4 has 4 times the DSP power of the old version it should run with 300mA according to manual. Are you using all outputs of your Pedal Power? You can also check the sticker on the FB2X4 PSU to see how much mA it delivers... i have a feeling that it might be considerably more and the manual could be wrong. i'll check it back in the office where i have a Fb2 x4 and pedal power digital
      • July 9, 2020
  • Qluster
    Newcomer - Level 1
    2020-07-02
    Hello, would the Ditto+ provide the rec/dub/play function (and not only rec/play/dub) like the x2? Thnx Q
    0 36
    • Qluster
      Qluster Today I got an answer from Nicolas Jones (musictribe support).
      He says: "Unfortunately it is not possible to change the operation mode on the Ditto+"

      And I replied: "Hello Nicolas, thank you for your kind reply.
      In this case I’m sure that the future will soon bring a stereo Ditto+ with the integrated possibility of switching
      between rec/overdub/play-mode and rec/play/overdub-mode."

      :)
      • July 14, 2020
  • Vittoriovibe
    Newcomer - Level 1
    2020-06-25
    Hi community, I purchased the flashback 2 x4 but I can't find the manual of the new toneprint editor because I can't understand how to save my presets on the PC and also I can't understand some parameters that are in the editor. finally, I couldn't even get the looper to work with the effects inserted, it only works without delay. Thanks for the help
    read more...
    0 49
    • Vittoriovibe
      Nigel67 Hi Vittoriovibe, please find the link below to the Editor Manual https://mediadl.musictribe.com/download/software/tcelectronic/tc-electronic-toneprint-editor-manual-english.pdf
      • June 25, 2020
    • Vittoriovibe
      Vittoriovibe Thanks a lot but the link it's the old editor, the new maybe still has not been released! You have a New flashback? Because the new manual of flashback 2 x4 it is not exhaustive and I was unable to solve the loop problem
      • June 26, 2020
    • Vittoriovibe
      Nigel67 Hi Vittoriovibe. The updated manual for the toneprint editor hasn't been finalised yet. A colleague will raise the question with the relevant team. I have put links below to TC You Tube videos which should help you in using your unit, including the toneprint editor. There are also many other videos buy other musicians that may help you as well if you make a search on the internet.
      https://www.youtube.com/watch?v=XJelHAoGTII
      https://www.youtube.com/watch?v=TmS2BBMU48A
      https://www.youtube.com/watch?v=SfIN63YMipw
      https://www.youtube.com/watch?time_continue=5&v=xBi9ikO6mT8&feature=emb_logo
      • June 29, 2020
    • Vittoriovibe
      Nigel67 Hi Vittoriovibe. The updated manual for the toneprint editor hasn't been finalised yet. A colleague will raise the question with the relevant team. I have put links below to TC You Tube videos which should help you in using your unit, including the toneprint editor. There are also many other videos buy other musicians that may help you as well if you make a search on the internet.
      https://www.youtube.com/watch?v=XJelHAoGTII
      https://www.youtube.com/watch?v=TmS2BBMU48A
      https://www.youtube.com/watch?v=SfIN63YMipw
      https://www.youtube.com/watch?time_continue=5&v=xBi9ikO6mT8&feature=emb_logo
      • June 29, 2020
    • Vittoriovibe
      fyxgy My M2000 has a dead battery
      • October 14, 2020
      • Help for new Editor flashback 2 x4
        Nigel67 Hi Mike, the battery inside is a LITHIUM BAT.. 3V/200mA. CR2032RV (Diameter 20mm x 3.2mm). It will require soldering into the pcb. If you want to send the unit in for repair, please go to the support tab at the top of the page and select the service option. You will fill out a form and a colleague will get back to you regarding servicing your unit. Many thanks
        • October 19, 2020
  • Nyfolk
    Newcomer - Level 1
    2020-06-23
    I have purchased another used M5000. When the unit is turned on, there is a message of "Serial Information Mismatch". I have tried to make contact at TC or Music Tribe to no avail. I would really hate to see this unit wind up as a door stop. Can someone direct me to someone who can get me a repair code? Thnak you!
    read more...
    0 101
    • Nyfolk
      RexBeckett I suggest that you open a Care ticket. At the top of this page, click Support -> Care -> Create a Care Ticket and select Type: Technical Support. Make sure that you enter all required (*) data before clicking Submit.
      • June 23, 2020
      • M5000 Serial Information Mismatch
        Nyfolk Good morning Rex, I have tried to do this already. The drop down menu does not include the M5000. Thank you!
        • June 23, 2020
      • M5000 Serial Information Mismatch
        Nyfolk I have followed the path to creating a care ticket. When I arrive at the request for model name, the M5000 is not listed. I do realize that this is a legacy product. Is there an email or phone number that I could reach out to discuss the issue and get resolution? I have had this issue many years ago and TC resolved this easily with a repair code. Thank you!
        • June 23, 2020
      • M5000 Serial Information Mismatch
        RexBeckett The usual solution for this is to use the model number of a similar product. Explain the reason in the problem description.

        The Care ticket is currently the only way to request technical support. Once the ticket is open, you should get a response by email. Keep watch on your email spam/junk folder.
        • June 23, 2020
    • Nyfolk
      Nigel67 Hi Nyfolk, if M5000 doesn't appear in the Product drop down, I would suggest choosing another TC Electronic product in the same category or as close as you can, and then put M5000 Help required in the Description and also Subject. If you want to reply on here with the case number, then I can pick up the case in the morning and assign it to the relevant person. Many thanks
      • June 23, 2020
      • M5000 Serial Information Mismatch
        Nyfolk Nigel, I have created a care ticket. The number is CAS-114126-V5B7Y8. Thank you!
        • June 23, 2020
      • M5000 Serial Information Mismatch
        Nigel67 I have your ticket and will pass it on to someone who can help.
        • June 24, 2020
      • M5000 Serial Information Mismatch
        slaterweezer Hi Nigel, I have the same issue today! If there is anyway at all you can help I would most appreciate it! My case number is: CAS-118452-P7M5G1
        • 1
        • ·
        • July 8, 2020
      • M5000 Serial Information Mismatch
        Nigel67 Hi slaterweezer, I have picked up your case. I think it is the same issue as Nyfolk which means having to change the internal battery. I will confirm this with a colleague in the morning and e-mail you back.
        • July 8, 2020
Go to page