The mono input on my Flashback 1 is intermittently cutting out. How do I send it in for service? Or is it even worth doing that? Service charges can often rival the cost of replacement. Thanks
Hello, I've bought used Delay FB mini 1 and it doesn't have a dry signal. I've tried to switch kill dry by using Toneprint (version 4.4.18 for PC) templates, but it did nothing. Any suggestions?
HALL OF FAME 2X4 REVERB: I know how to use the Tone Print Editor to create and save my own Tone Prints, but how do I assign my Tone Prints to the 4 FOOT SWITCH PRESETS?
My Mic Mechanic 2 has started playing up. The Effect LED, the Tone LED and the Power LED are on all the time. I cannot turn Tone off bypressing the Tone button - I cannot turn the Effcets off by pressing the footswitch. Same problem whether using batteries of Power Supply. How do I reset this device?
Hi, is there any way to identify what TonePrints are downloaded into spots 1-3 of my flashback2 and hall of fame2? Thank you.
I guerss it's possible to combine two or more settings, but I'm stumped at just how to do it. For example, if I wanted to combine reverb with the AM Radio effect...what are the step by step procedures to do this?
hi there
having the same issue as Shamusotoole, where s/he states:
"I bought a Flashback 2 with the aim of mono input, external tap, and stereo out." and ends up frustrated.
i was looking for:
mono in, dry+quarter notes out in one amp, dry+dotted eights in the other.
this is perfectly possible with nothing plugged into the R input. it is also perfectly possible with a splitter cable, sending the exact same signal to L and R inputs. until you enable external tap in the editor, that is.
since this is clearly a dual delayline equipped pedal, that can do mono to stereo or stereo to stereo just fine, i find it hard to wrap my head around the reason why enabling the ring on one of the inputs to accept pulses would cause the stereo spread of the outputs to be summed to mono. if it can do mono to stereo with nothing plugged in the R input, hopefully this is a software matter? where it can be programmed to do that very same thing, only while listening for taps on the ring?
i found myself eyeballing the Nux duotime. while that doesn't have external tap tempo (want to control time from a Boss ES-5), i prefer its dedicated tap tempo switch over holding down the switch on the flashback. but i think it sounds a little flatter than the flashback, and buying another delay pedal that almost does what i want is getting old. (looking at you, Nemesis.)
but seriously, there has to be a reason for Nux to make these - me and Shamusotoole can't be the only one looking for this functionality? and the Flashback 2 comes soooooo darn close..
seriously, a firmware upgrade that provides this would make this pedal the single best thing since sliced bread. smallest form factor (pedalboard real estate matters!), and an offering that no other manufacturer has provided, with a superb sound.
please? pretty please? :)
thank you Pedro. you got my hopes up for a minute :) but i'm quite sure my Flashback 2 is already running the 2019 #1.2.00 firmware, since i already have the internal tap tempo working, which was new to that firmware update. and while the 'new' internal tap tempo mode for the linked firmware retains full stereo as advertised, what i'm asking for is for the EXTERNAL tap tempo to retain the stereo image. which this firmware does not do. but i'll doublecheck the firmware next time, just to be sure.
I recently bought a used flashback 2 and I found that when turning delay time up past 12 o oclock there is no initial dry signal . so i hit anote and dont hear anything until the delay kicks in . I see there are a couple switches inside the box for bypass/dry kill but nothing changes in regards to this when I switch them . One of them will cut the signal if the pedal is off and switch it back and it works fine . but the kill dry thing seems to not be working . I updated the pedal and dont know what eles to do .
any helpappreciated
Hello, is there a way to get the Hall-Effect Sensor for the Flashback 2?
It is the IC20 and the part is mechanically broken.
Musicstore could not/refuse to replace the part within the guarantee time..
this is quite sad, because the pedal work. but I cant switch it.
why should I throw away a 110€ pedal when a 2€ part is broken?