Statistics

298,815 members
182,480 posts
  • New
    Ferdnuckles
    Newcomer - Level 1
    2022-09-27

    Have an FCA1616, Line 6 HD500x, Rode condenser mic... can I plug guitar 1/4 into FCA port 1, condenser mic into Port 2, and route out to input on HD500x POD, out from HD500x via USB to computer and record in my DAW...Want to apply effects to both guitar and vocals individually prior to recording... what is the best way to cable these connections,.. out to HD 500X then to computer, or loop output from FCA1616 to Line 6 then back into FCA then via FCA USB connection to computer??  In any case, how to I link everything up??

     

    Thanks

     

    Marc

    read more...
    0 0
  • New
    Noctxm
    Newcomer - Level 1
    2022-09-23

    It's not the first mixer I've had to have this exact issue, I've tried a basic ground loop isolator, an iFi iDefender and plugging it in to other sockets/usb ports. The clip has the audio with just power/USB cable and no XLR and then with an XLR cable later in the clip. I've been trying to fix this for almost 2 weeks with no progress. 

    read more...
    0 3
  • New
    dkamhaji
    Newcomer - Level 2
    2022-09-17

    Need Help with external FX Routing -using AUX SENDS 1/2

    I need help understanding and setting up my 2 external fx processors to this mixer so that I can use the aux 1/2 knobs to send vol to each channel. Im trying many diffrent routes and Im having trouble understanding the right way to do it on the QX1832. My original attempt is that I have it going from Send 1 and Send 2 jacks into my effect processors inputs. I then wanted to use the aux1 and aux 2 knobs on each channel strip to introduce the effect per channel. By the way I have the effect processors outs, unconventionally plugging into Ch 3/4 and 5/6 panned hard left and right (instead of using the returns) the reason for this is that I want to specifically route the effects sound through the mixer's sub outputs instead of main outputs - and this woudl be the only way to do it. part of my set up needs... So I can get the sound of effect 1 through send 1 but not for send 2. if I switch the cables of send 1 and 2 I can hear the other effect that wasn't sounding now sounding.. so essentially I cannot get to hear both send outputs at the same time layered or summed. the only way so far I have been able to get both to sound is by plugging in one effect to the send 1 and the second to mon out and using the mon fader to control fx2 volume.. it works, im not exactly sure what is happening in this set up.. would love to understand it a bit more.. but I would rather have both effects on send 1 and 2 working if possible.. im not sure if something is hardwired in a way where this is not possible and would love some help to get this set up correctly.

    Thank you!

    read more...
    0 0
  • New
    rickeyboards
    Newcomer - Level 1
    2022-09-20

    I get a load, high pitch squealing noise when I run the monitor signal from my JBL Eon One through any channel of my Behringer X18 mixer.  The monitor signal works fine through other analog mixers.  The squealing occurs with different power amps, different DIs and different cables.  I also get the squealing with the line-out from a Carvin bass amp.  Other line-outs work fine.  I have my my bus 6 signal routed to USB output for live streaming. 

    read more...
    0 1
    • rickeyboards
      NicJonesMT Hi RickeyBoards.
      Please click support at the top of the page and submit a technical support ticket.
      • Sep 22
  • New
    Tomg123
    Newcomer - Level 1
    2022-09-19

    Are there any techs from Behringer or Behinger certified techs that will do trainings on the X32?

    [email protected]

    0 0
    • Tomg123
      Nigel67 Do you mean tech as in repair, or tech how to operate the X32? If its operate, then I would advise taking a look at this You Tube channel https://www.youtube.com/c/DrewBrashler/videos. I think Drew goes through just about everything you need to know about the X32. Some of it is pre V4 firmware, but all of it is relevant and can be easily converted to V4 firmware. You should be able to learn just about everything from his site.
      • Sep 22
  • New
    HazelMears
    Contributor - Level 1
    2022-09-04

    Hi, we use the XR18 connected into our Macbook Air for our livestream (into OBS) however the Mac has stopped recognising the XR18 as a sound input. Its listed as a device but doesn't show as active.

    I've changed cables, even tried it on a different Macbook which didn't even detect it as being there. We're currently on 1.18 for the firmware, could this be the issue?

    Has anyone else had this issue and/or does anywhere know where I can get the earlier firmware versions from? I have seen in other forums that the mac os stopped recognising the XR18 but they got it going using an earlier firmware. I'd rather not downgrade it but if that would get it working again I'll do it! Thanks.

    read more...
    0 4
    • HazelMears
      Nigel67 Hi HazelMears. This seems more hardware related than firmware. However, you can find older versions of firmware at this link - https://www.behringer.com/downloads.html. Select XR18 in the Product column and Software in the Type column. You will then need to tick the box labelled 'Show all Versions' and the older versions of firmware will appear. Have you tried a factory reset on the unit. This sometimes works.

      Any show / presets that you have on the unit will be deleted.  With the unit powered, locate the hole in the front panel by the access point logo.  There is a switch behind the hole.  Push something through the hole gently until you feel a click as the switch activates.  Hold the switch in for 12 seconds and when you release, the unit will reset.  Set up the connection again and see if you can connect back up to the USB port.

      If this does not work, I would suggest filling out a Technical Support ticket and we will be able to advise further. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Technical Support tab and submit a ticket.
      • Sep 5