Statistics

208,481 members
80,682 posts
  • Bigpine
    Newcomer - Level 1
    2021-01-05

    I'm looking for bias information regarding a bc30. 

    0 3
  • New
    JoeRojas
    Newcomer - Level 2
    2020-12-26

    As an owner of a 6260 Guitar Head and a G5 Head, I wonder if Bugera will make a Mini Head of a 6260? I play metal and use my 6260 (Which I love). At small venues I use the G5 with a 1x12 cabinet. To me, it does fell a bit awkward taking a good looking boutique amp to music situation where the amp need to look mean. Here's my question to Bugera, Will there be a desire to make a 6260 Mini Head that will sound like it's big brother? Just Asking.

    read more...
    0 3
  • earman72000
    Newcomer - Level 1
    2021-01-08

    I have been trying to send it in, for repairs, for 28 months. I can't get any answers.

    I will ship it, if only I knew where to get it fixed. I do not have the bill of sale, so I cannot register a care ticket.

    Any advice???

    Peter

    read more...
    0 2
  • New
    russellcatchpole
    Newcomer - Level 1
    2021-01-05

    Hi, I have bought a PS1 Powersoak. It's all good but if I run my Vox NT50 flat out into it with a 2x12 cab attached, even with the powersoak set to the lowest volume, it's still too load to play in my flat late at night.

    So, is it safe to use it without the speaker attached and the soak volume set to a little more than the lowest, then I can use the line out into a mixer & use headphones. I say, little more than lowest becuase the line out is wierdly controlled by the large soak volume wheel, so when that's set to lowest, virtually nothing comes through the line out apart from hiss & hum.

    The manual is quite ambiguous on this.

    read more...
    0 5
    • russellcatchpole
      DavidKnighton Hello Russell,
      The manuals states that "even with the SOAK set to 100, the power output will be about half of the amplifiers rated output". This means if you have a 100 watt amp, you're effectively reducing the output by about by 50 watts with Soak set to 100.

      All that being said, I think it would be wise to maintain the speaker load of the cabinet, as most amps do not function correct without the speaker load. What I would suggest is to turn the Master volume down on your amp to compensate. Also, you might want to check and see if you can disconnect one of the drivers in your cabinet to change the load impedance. If you can disconnect one driver, you may increase the load impedance, which will draw less power from the amp, and in turn may reduce the volume a bit. If you do this, make sure you check the impedance value of the speaker and use the correct impedance setting on both the PS1 and the amp head.
      • Jan 6
  • New
    Randyp64
    Newcomer - Level 1
    2021-01-09

    I recently purchased a Bugera V55HD from zZounds and have only used it for approximately 4hrs and there is a humming sound that goes load and soft in and out as a loss of power is noticeable. I turned the head around and both red lights are on to replace the tubes. What should I do about this? I would change the tubes myself if you can supply them instead of trying to repackage it and ship it back. All I’m asking for is new tubes and I won’t bother you again. Thanks, Randy 

    I really like the amp and plan on purchasing the Bugera V22HD if everything works out with this one... 

    read more...
    0 11
    • Randyp64
      Nigel67 Hi Randy, if the unit is brand new and under 30 days, you should go back to the shop that you purchased it from and ask for a DOA. If it is over 30 days, but still under warranty, then we can repair it for you. It will be possible for us to send you the replacement tubes, however you will lose any remaining warranty because you have gone inside the unit. Please click on the support tab at the top of the page. On the new page that opens, scroll down and submit a service ticket where one of my colleagues will be able to help you further. Many thanks
      • Jan 10
    • Randyp64
      Randyp64 I have not heard anything about my possibly getting replacement tubes for the Bugera V55?
      • Mon at 3:59 AM
    • Randyp64
      Randyp64 I filled out the information order many days ago and have not heard back from anyone if I can’t get the replacement tubes I will send it back and take a refund. It’s no use to me unless I put more money into it and I don’t want to go that route please let me know when or if something can be worked out. Thanks, Randy
      • Mon at 4:06 AM
      • Bugera V55 loss of power and red lights are on
        Nigel67 Hi Randy, I am very sorry for the late reply to your ticket. Do you have the ticket number and I can find out why it hasn't been answered. Many thanks
        • Mon at 7:35 AM