Statistics

249,419 members
126,425 posts
  • New
    BartVervenne
    Newcomer - Level 2
    2021-09-13

    Last week I had a theatre show with 70+ channels and about 100 scenes.

    1. I had some strange behaviour with files saved on the cloud. Names of channels where lost when I opened the cloud file on my computer (picture included)

    2.There was a problem with storing scenes, on some channels the changes I made were not stored when applying 'Store to current scene', I did't find any logic in it (except that it were always the same channels and I even think it were the channels where the name was lost in the cloud file) . This made my automation useless.

    3.I found it very complex to make changes with that amount of channels and scenes. It would be usefull to be able to select a channel and then apply changes to a range of scenes that can be entered in a popup screen. Now I found it difficult because you can only apply changes on the zoomed range or am I doing something wrong? A training video concerning automation would be very much appreciated.

    4.The numberering of scenes is in my case useless. I need to be able the enter a chapter-part-subpart number (like 5.1.1 - 5.1.2 ...) for theatre shows. The automatic numbering gets very confusing when you have to enter a scene in between because all scenes after are renumbered. This would be much easier in a seperate field because now I have to combine it with the name since there is only one entry available. I would also appreciate a popup screne to enter number and name automatically after entering a new scene.

    5.I also found it very slow when I was in scene 85 to return to scene 15 because I had to scroll on the screen. A popup with goto scene ... would be a appreciated. 

     

    read more...
    0 7
    • BartVervenne
      john0121

      Hi Bart, sorry to hear about the problems with your showfile. Could you please submit the tech support form via the support button at the top of the page. We can then track this with our quality and development teams to ensure fixes/ solutions. Thanks

      • Tue at 4:38 AM
  • New
    Wils0n
    Newcomer - Level 1
    2021-09-16

    Hi 

    We have Midas M32 at our church and recently the guys complained that they can hear everything i'm doing in their IEMs and i changed the settings of the console mix output configuration to 8+4+4 (which is 8pre(post EQ) + 4subgroups + 4post) whereby the 8 is for the band on stage and 4 i'm using as sub groups for band then the last 4 i'm using for FX,now the issue that i'm having is both me and the band we are able to adjust the mixes but we can't adjust the overal volume fader of their mix sends can anyone help me how i can change the mix main fader to work again and be able to adjust the levels of IEMs..

     

    Thank you

    read more...
    0 11
    • Wils0n
      Paul_Vannatto Go to where you have the mix outputs assigned (probably the Routing, Out 1-16 screen) and change the taps of each of the taps (for the musician's IEMs) to post fader.
      • Thu at 9:16 AM
  • New
    tlbreaux99
    Newcomer - Level 1
    2021-09-13

    Midas (Music Tribe) support has really gone downhill.  I cannot belive there is not a phone number to actually talk to a person.  This causes a huge delay and after numerous emails, i still have not gotten a response.  This is totally unacceptable and not very professional.  Our Midas board was sent in for repairs and sent back to us.  Two other items that i had listed did not get repaired because Music Trible did not have that info on the work order.  So now i am stuck again with issues and not getting answers..  Very frustrating.

    read more...
    0 18
    • tlbreaux99
      DavidKnighton Hello tlbreaux99,
      Sorry to hear of your experience. We do have a phone number for ENTE support, but it is reserved for critical situations. I'll take a look as to why your emails are not being addressed. It's possibly you're replying to the wrong email or our replies are ending up in your SPAM/JUNK folder. Please pass your case number(s) and RMA number to me and I'll investigate.
      • Mon at 2:25 PM
  • New
    DiogoGregorio
    Newcomer - Level 1
    2021-09-12

    Good people!

    This is a long shot, lets see if anyone did or have any idea how to do this or if its possible at all.

    I have an XL4 installed in an OB van (yeah, I know) while it sounds pretty nice the dreaded Outboard Electronic module just give up on me.

    I lost the group routing capability, the aux routing is erratic and when you press 1 it turns on 13 also, our other random aux and turns off other random aux.

    All automation don't work, VCA, routing, and all kinds of momentary switches.

    My question is, is it possible to bypass the automation module, having access to the group and aux routing and not using the VCAs at all?!

    Cheers! 

     

     

     

    read more...
    0 4
    • DiogoGregorio
      Dale_M Hi there, as the XL4 is very old there is now very limited resource and support for it, however there is an excellent Facebook page with lots of Pro Users (many with XL4/H3 consoles) who are much better placed to advise you, I would suggest joining this group and adding your post, sorry we are unable to help any further: https://www.facebook.com/groups/1976275959349445
      • Wed at 11:34 PM
  • New
    gkilsti
    Newcomer - Level 1
    2021-09-08

    Man, I wish there was a way to get 16 input channels on the faders, which is what I need 95% of the time I mix live.
    I hope there is a very good technical/hw reason for not allowing this, because it seems like it would be very easy to accomplish since the left side can already have BUS 1-8 or BUS 9-16 and the two sides look so very similar.


    If this is just a software choice/limitation, then please update the firmware to allow for example a button-press of 1-8 AND 9-16 together to get all those 16 channels on faders.

    This would make the mixer totally perfect for my gigs :)

     

     

    read more...
    0 6
    • gkilsti
      MarkNorgren Not sure what your asking? But if you push both buttons at the same time (1-8 and 9-16), the board will display channels 1-16 at the same time. Is that what you mean?
      • Sep 8
    • gkilsti
      gkilsti

      Wow, it actually works like that! Fantastic! Don't know why I never actually tried that...Thanks Mark :)

      • Sep 8
  • New
    Kmorgan1251
    Newcomer - Level 1
    2021-09-05

    My Midas Pro2 starts to boot up, all the buttons light up but the monitor display does not come on. The buttons stay lit for about 20 seconds, the there go out and the console does not boot up. The lights on the power supplies in the back of the console are green. What else can I check?

     

    read more...
    0 3
    • Kmorgan1251
      Nigel67 Hi kmorgan1251. This is the MC not starting up. It is probably caused by the BIOS battery voltage dropping below 3.00 volts. The battery may need replacing. With the power switched on, try pressing the MC reset switch in the rear of the frame by the power supply and see if this starts up the console. Even if it does, you will still need the BIOS battery changing. Can you submit a Technical Support ticket and we will then be able to help you further. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Technical Support tab and submit a ticket.
      • Sep 5
  • New
    aarontroughton
    Newcomer - Level 1
    2021-09-03

    Hello all, apologies if this has been covered but im new to the forum.  Which version of the Midas Edit software is everyone rocking? Last few freelance gigs I've done have been in M32 land but getting a firmware compatibility issue. Consoles have been patched to 4.06, software version I'm using is PC 4.3 so I'm guessing a dial back on the software is needed...? Can't seem to find any legacy versions on the web... Any help from the hive mind would be greatly appreciated.

    read more...
    0 5
  • New
    jjfredrick
    Newcomer - Level 1
    2021-09-01

    Is it plossible to save mix presets on SD Cards.  I am an audio enginner at the church that has 20+ band members that rotate in an out of the band each week.  Our church recently upgraded to a Midas M32, DL32, Hub4, and DP48 personal mixers and it would be ideal to be able to save each of their DP48 mixes to an SD card that can then be loaded on whichever DP48 unit they might be using in a given week they are volunteering.

    Admittedly, I'm still getting up to speed on this system, so perhaps I have overlooked an easier solution, but welcome any insights and/or suggestions for managing this scenario.

    read more...
    0 2
    • jjfredrick
      Paul_Vannatto Hi Jeff, yes you can save mix presets to either the 12 internal memory or 12 preset files on the SD card. Press the Setup and SD Rec buttons simultaneously and a menu will come on the screen with Load, Save, Delete, Read, Write, etc.). Select the Write, then one of the 12 group buttons to save to the SD card. It will save a file in the DP48M folder, such as dp48_sd_pre_01.bin (last 2 digits will be preset number). Selecting the Read, then one of the group buttons to load the desired preset from the SD card.

      If you want to have specific presets affiliated to specific musicians, I would suggest you create individual folders on a hard drive named by the musicians' names and place the appropriate preset files in them. Unfortunately the files have to be named exactly as shown above, or the DP48 will not read them.
      • Sep 1
  • New
    ReinhardKlamm
    Contributor - Level 2
    2021-08-31

    Hi folks

    I am now on the DP48 Trip using POE and this works fine. Now it would be great to get this POE Based Stagebox DL8. Any Information about this?

    0 7
    • ReinhardKlamm
      DavidKnighton Hello Reinhard,
      The product development is unknown at this time. I would check back periodically, as nearly all product releases are posted here in the community.
      • Aug 31
  • New
    rockbill01
    Newcomer - Level 1
    2021-08-31

    How are you!

    I live in Suwon, South Korea, and am an office worker who is interested in sound equipment.

    I had an idea for a wireless method during acoustic monitoring for a long time, so I sent it to AVIX & CUOSHOP the official Korean importer of Midas & Behringer, to propose and discuss it.

    The wireless WIFI monitoring app development book and STAGE WAVE & other monitoring APP Guide materials are attached as additional materials through AVIX.
    In the future if necessary, we will make it into a translated material and provide it.

    Currently, I am in charge of circuit parts in JIG and equipment assembly and manufacturing at Samsung VD and a primary supplier (Na & Na).

    In general, in relation to monitoring, it is a form of using one's own smartphone as a monitoring device from a wired method using

    Behringer P16-M to a wireless network method using WIFI Router. Innovative products are being launched to support you.

    We have analyzed STAGE WAVE App, which is currently the most emerging, and we would like to suggest a way to develop more advanced than

    STAGE WAVE App by identifying the improvements in the network of that APP.

    Advantages of STAGE WAVE: App compatibility / stability / Low latency possible (latency changes depending on the setting)

    Cons: Requires high-performance Router and mid-range performance smart phone
    Amount of high-power WIFI data / Monthly flat rate

    Advantages of the New Behringer App (temporary name): Intermediate performance Router / Entry-level Smart Phone support available

    Basic output WIFI data amount / Calculation of reasonable monthly fixed amount for users

    Development and sales of PC-only and WIFI Router combined (small-scale) models

    There are additional materials reviewed and analyzed to make this proposal, and ideas related to Line Up that will be upgraded in the future from

    this proposal model are also being prepared.

    Please review the contents first, and if you need interest or discussion about my proposal, please message & call.

    thank you.

    [email protected]

    082-10-2780-1587

    H.K.Oh (Hong Kyun Oh)

    read more...
    0 11
    • rockbill01
      Paul_Vannatto You have already posted this once before and got a response from the company. This is an end user forum. So it is inappropriate to post this here multiple times. Please delete this thread.
      • Aug 31
    • rockbill01
      rockbill01

      Hello. Paul_Vannatto

      Sorry for posting the same content multiple times.

      As you said, I clicked the function to delete the discussion, but the content is not deleted normally.

      thank you.

      H.K.Oh.

      • Sep 1
Go to page