Statistics

251,062 members
128,292 posts
  • New
    Kmorgan1251
    Newcomer - Level 1
    2021-09-05

    My Midas Pro2 starts to boot up, all the buttons light up but the monitor display does not come on. The buttons stay lit for about 20 seconds, the there go out and the console does not boot up. The lights on the power supplies in the back of the console are green. What else can I check?

     

    read more...
    0 6
    • Kmorgan1251
      Nigel67 Hi kmorgan1251. This is the MC not starting up. It is probably caused by the BIOS battery voltage dropping below 3.00 volts. The battery may need replacing. With the power switched on, try pressing the MC reset switch in the rear of the frame by the power supply and see if this starts up the console. Even if it does, you will still need the BIOS battery changing. Can you submit a Technical Support ticket and we will then be able to help you further. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Technical Support tab and submit a ticket.
      • Sep 5
  • New
    aarontroughton
    Newcomer - Level 1
    2021-09-03

    Hello all, apologies if this has been covered but im new to the forum.  Which version of the Midas Edit software is everyone rocking? Last few freelance gigs I've done have been in M32 land but getting a firmware compatibility issue. Consoles have been patched to 4.06, software version I'm using is PC 4.3 so I'm guessing a dial back on the software is needed...? Can't seem to find any legacy versions on the web... Any help from the hive mind would be greatly appreciated.

    read more...
    0 8
  • New
    jjfredrick
    Newcomer - Level 1
    2021-09-01

    Is it plossible to save mix presets on SD Cards.  I am an audio enginner at the church that has 20+ band members that rotate in an out of the band each week.  Our church recently upgraded to a Midas M32, DL32, Hub4, and DP48 personal mixers and it would be ideal to be able to save each of their DP48 mixes to an SD card that can then be loaded on whichever DP48 unit they might be using in a given week they are volunteering.

    Admittedly, I'm still getting up to speed on this system, so perhaps I have overlooked an easier solution, but welcome any insights and/or suggestions for managing this scenario.

    read more...
    0 5
    • jjfredrick
      Paul_Vannatto Hi Jeff, yes you can save mix presets to either the 12 internal memory or 12 preset files on the SD card. Press the Setup and SD Rec buttons simultaneously and a menu will come on the screen with Load, Save, Delete, Read, Write, etc.). Select the Write, then one of the 12 group buttons to save to the SD card. It will save a file in the DP48M folder, such as dp48_sd_pre_01.bin (last 2 digits will be preset number). Selecting the Read, then one of the group buttons to load the desired preset from the SD card.

      If you want to have specific presets affiliated to specific musicians, I would suggest you create individual folders on a hard drive named by the musicians' names and place the appropriate preset files in them. Unfortunately the files have to be named exactly as shown above, or the DP48 will not read them.
      • Sep 1
  • New
    ReinhardKlamm
    Contributor - Level 2
    2021-08-31

    Hi folks

    I am now on the DP48 Trip using POE and this works fine. Now it would be great to get this POE Based Stagebox DL8. Any Information about this?

    0 10
    • ReinhardKlamm
      DavidKnighton Hello Reinhard,
      The product development is unknown at this time. I would check back periodically, as nearly all product releases are posted here in the community.
      • Aug 31
  • New
    rockbill01
    Newcomer - Level 1
    2021-08-31

    How are you!

    I live in Suwon, South Korea, and am an office worker who is interested in sound equipment.

    I had an idea for a wireless method during acoustic monitoring for a long time, so I sent it to AVIX & CUOSHOP the official Korean importer of Midas & Behringer, to propose and discuss it.

    The wireless WIFI monitoring app development book and STAGE WAVE & other monitoring APP Guide materials are attached as additional materials through AVIX.
    In the future if necessary, we will make it into a translated material and provide it.

    Currently, I am in charge of circuit parts in JIG and equipment assembly and manufacturing at Samsung VD and a primary supplier (Na & Na).

    In general, in relation to monitoring, it is a form of using one's own smartphone as a monitoring device from a wired method using

    Behringer P16-M to a wireless network method using WIFI Router. Innovative products are being launched to support you.

    We have analyzed STAGE WAVE App, which is currently the most emerging, and we would like to suggest a way to develop more advanced than

    STAGE WAVE App by identifying the improvements in the network of that APP.

    Advantages of STAGE WAVE: App compatibility / stability / Low latency possible (latency changes depending on the setting)

    Cons: Requires high-performance Router and mid-range performance smart phone
    Amount of high-power WIFI data / Monthly flat rate

    Advantages of the New Behringer App (temporary name): Intermediate performance Router / Entry-level Smart Phone support available

    Basic output WIFI data amount / Calculation of reasonable monthly fixed amount for users

    Development and sales of PC-only and WIFI Router combined (small-scale) models

    There are additional materials reviewed and analyzed to make this proposal, and ideas related to Line Up that will be upgraded in the future from

    this proposal model are also being prepared.

    Please review the contents first, and if you need interest or discussion about my proposal, please message & call.

    thank you.

    [email protected]

    082-10-2780-1587

    H.K.Oh (Hong Kyun Oh)

    read more...
    0 14
    • rockbill01
      Paul_Vannatto You have already posted this once before and got a response from the company. This is an end user forum. So it is inappropriate to post this here multiple times. Please delete this thread.
      • Aug 31
    • rockbill01
      rockbill01

      Hello. Paul_Vannatto

      Sorry for posting the same content multiple times.

      As you said, I clicked the function to delete the discussion, but the content is not deleted normally.

      thank you.

      H.K.Oh.

      • Sep 1
  • New
    vassallo90
    Newcomer - Level 1
    2021-08-30

    hey iv just bought a Midas f32 and noticed it's pre fader. Is there a Mod to fix to Post Fader?

    And who is available to do this working in Melbourne Australia?

     

    regards 

    0 17
    • vassallo90
      Dale_M There is a mod that can be done but we advise an official Midas repair centre perform it. For more info please submit a Technical ticket from the Support tab above.
      • Aug 30
  • New
    emadtoma
    Newcomer - Level 1
    2021-09-18

    Hello everyone,

    I am trying to buy Midas M32R live but its out of stock in USA. Does anyone can help me where can I buy it?

     

    Emad

    0 14
    • emadtoma
      Paul_Vannatto If Sweetwater doesn't have it, good chance no one else in the US will have it in stock. This is probably due to the global chip shortage and supply chain issues which are only going to get worse.
      • Sep 18
    • emadtoma
      Dale_M It is worth checking the official sellers from the Buy tab at the Midas website https://www.midasconsoles.com/
      • Sep 18
  • New
    rossilive
    Newcomer - Level 1
    2021-09-13

    Hello,

     

    For Studio use, I'm trying to route the channel Solo monitor output to the main out, not on a separate Monitor out as it is configured. When I hit the solo button, I want to hear only that channel out of my Mains.

     

    Thanks in Advance!

    read more...
    0 1
    • rossilive
      Paul_Vannatto Assign the Monitor L & R to a couple of user outs (on the Routing, User Out screen, last 2 assignables in the Aux group), then assign those User Outs to the respective outputs (eg. AES50 A, B, XLR Out, etc.) that you have your speakers connected to.
      • Sep 13
      • M32 Console - Solo channel to Main out Routing.
        rossilive Tried like this, didnt seem to work. I'll try again and send images if not... Thanks!
        • Sep 14
  • New
    Nitram00
    Newcomer - Level 1
    2021-09-07

    bonjour a tous.
    je viens de faire l'acquisition du midas m 32R live , j'aimerai enregistrer le produit afin de bénéficier de la garantit midas, mais my god le site ne veux pas me laisser entrer la date d'achat, ce qui ne me permet pas de pouvoir valider l'enregistrement.
    le site est il en chantier? avez vous eu une quelconque difficultée a enregistrer vos produits ou je n'ai tous simplement pas de chance en informatique?:D

    read more...
    0 4
    • Nitram00
      Nigel67 Hi Nitram00. I am sorry for the bad experience registering your product. Can you send me a picture of the screen when you are entering in the date of purchase please and also a picture of the error message that you are getting. I will report this to the web team to fix. What happens if you put another date, does that work? If so, you will receive an e-mail back confirming the registration. If you let me know the case number then I can adjust the date of purchase accordingly. Many thanks
      • Sep 7
      • enregistrement produit midas m32R live
        Nitram00 Salut Nigel67
        merci pour ta réponse rapide , en allant chercher une date plus lointaine j'ai pu débloquer le bug et finalement mettre la bonne date correspondante.
        le bug en question était que au lieu de m’afficher des nombres correspondant a la date , il s'affichait "nan-nan-nan".
        dsl je n'ai pas pu prendre de photo a temps pour te montrer.
        en tout cas pb résolu , merci encore
        • 1
        • ·
        • Sep 8
  • New
    GpDav
    Newcomer - Level 1
    2021-09-01

    Church installation.  M32 is never moved.

    Firmware version 4.04.1 installed.  Unit is approximately 2 years old.

    The last three church services, two week period, the M32 has "locked up" during the 1 hour service.  The display screen goes black, the preamp mic input still shows green LEDs active indicating signal into the M32.  All other LEDs go very dim.  The output goes away with no signal to the power amp.

    Unit is shut off via power switch and then turned back on.  Unit comes back on and operates normally.  Is this a software issue or hardware power supply??  Do we need to erase all the memory and reinstall software?  Getting ready to order a spare power supply.

    Please advise

    Thanks Dave

    read more...
    0 7
    • GpDav
      Paul_Vannatto Hi Dave, those symptoms seem like a faulty power supply. I would suggest you submit a warranty ticket by clicking on the Support above.
      • Sep 1
    • GpDav
      GpDav Hello Paul, Thanks for the quick advice.
      • Sep 1
Go to page