Statistics

227,655 members
102,424 posts
  • New
    mvsounds
    Newcomer - Level 1
    2021-05-03

    I just purchased this mixer for Zoom online lessons. What I discovered after the set up, is when I connect the microphone and the headphones, when i connect on Zoom, either I can listen to my student or myself, but not both of us together. There has to be a  way where I can hear both of us in headphones, it should be so simple but I could not find it. Anyone who knows a way around it? The audio inputs and outputs in Zoom are USB AUDIO CODEC.

    read more...
    0 13
    • mvsounds
      RexBeckett Hi mvsounds, there is a way around this. Connect both 2-Track Out to 2-Track In with a pair of short RCA/RCA cables. Press the USB/2TR To Phones/CTRL Rm button. Now you should hear both Zoom sound and your local mix through the Phones output. You may need to use the PC's output level control to adjust the mix.
      • Tue at 2:43 AM
  • New
    haeleng
    Newcomer - Level 1
    2021-04-22

    Hi, I have an weird issue with my S16 boxes.

    Equipment used to test are X32 compact, X32 core, 3xs16

    1) When I connect a S16 to a X32 compact both X32 and S16 seem to be in sync.
    2) However Channel 14 can not be setup from the front panel, both phantom and/or gain settings can not be set from the front panel of the S16. All other channels on the S16 can be set from the S16 front panel
    3) Phantom and gain from channel 14 can be setup from the X32 compact. So first I thought something is wrong with one the S16 units.
    4) Channel 14 cannot be set from the front panel even when I swap S16 units. So it is not the hardware of the S16
    5) Channel 28 (16+12) can be set from the S16 front panel.
    6) Changing length from 50 to 2m of the AES50 cable has no effect.
    7) Connecting a S16 to a X32 Core gives the result that channel 12 and 13 cannot be set from the front panel, and suddely ch 14 (phantom and gain) can be set from the S16 front panel. Besides all channels (als 12, 13) can be set from X32 core software (X32edit)
    8) There are no connections made, only the AES50 cable is connected, to minimise possible EMC issues.
    9) When the S16 is set to standalone mode Ch12,13,14 can be set. So it has to be something between X32 and S16
    10) All S16 units had firmware 2.2 Update firmware to version 2.4 did not help.

    Anyone out there who ran into this problem. Any other ideas are welcome.

    read more...
    0 9
    • haeleng
      GaryHiggins If you have your scenes and everything safely on a usb drive. I would suggest initializing the mixer (maybe both) and then try. It sounds to me like a strange routing thing. You can sift through your routing after, if it gets fixed, Also with the latest S16 firmware there are several new modes added. Make sure you go all the way counter clockwise with the config button depressed to get to the very first and then step forward to the correct mode desired for each S16. Daisy Chain Master modes do some odd things for shifted ch's (on purpose) Sometimes certain modes look like just like another and they are not. A thought or anyway.
      • Apr 22
  • New
    Steelewolf
    Newcomer - Level 1
    2021-04-15

    Hi,

    I recently got Ableton Live 11 Suite and I want to record my churches worship services, but I cannot figure out how to do the routing so that the input/LC signal is sent to the expansion card.

    My church has an X32 Rack, and I am using X32-Edit without the mixer right now to figure out the routing.

    How do I tap the signal from input/LC and send it to the X-USB Card?

    Thanks.

    read more...
    0 21
    • Steelewolf
      RexBeckett Hi Steelewolf, the normal routing for recording is to take the signal directly after the preamp. This is done on the Routing -> Card tab. The attached screenshot shows the routing to record the sixteen local inputs on an X32 Rack plus sixteen inputs from a stagebox on AES50-A.
      • Apr 15
  • New
    Steelewolf
    Newcomer - Level 1
    2021-04-13

    Hi,

    I just got a new USB drive for use with my X32 Rack, but it only supports NTFS and exFAT file systems. I saw on the Behringer Wiki, linked here that the 2-track recording works with FAT12, FAT16, and FAT32 formatted drives. My question here then is, can I use an exFAT formatted drive with my X32 console?

    Thanks

    read more...
    0 20
    • Steelewolf
      Paul_Vannatto No, the X32 only support the FAT32 (as well as the older FAT16 and FAT12). The recorder/playback is meant to be used with a USB stick, not a drive
      • Apr 13
  • New
    Wing2021
    Newcomer - Level 1
    2021-04-23

    Can I connect 3 DL 16's or 1 DL 32 plus 1 DL16, to operate Wing as a full 48-channel console?

    0 19
    • Wing2021
      Paul_Vannatto Yes you can. If you choose the DL16 + DL32, the DL32 needs to be the last in the chain. This is because the DL16 is designed for cascading (adding more stageboxes), whereas the DL32 is not.
      • Apr 23
    • Wing2021
      ValeriuM_Trufin Paul, I think you are mistaken.
      We have a DL32 + an S16. The DL32 is first, and the S16 is second in the chain. I suspect that DL16 is identical to the S16 in options, so you can set the DL16 to be at +16, just as you would set the third one in a 3xDL16 configuration.
      • Apr 23
    • Wing2021
      KlausMock On each AES50 connector you can transmit 48 channels in each direction. So with one line from the WING to the stageboxes you can use 48 mono signals at once. And I am with ValeriuM_Trufin, connect the DL32 to the WING and the DL16 to the DL32. I am, at least doing that all the time.
      • Apr 23
    • Wing2021
      GaryHiggins These (and all) stage boxes each have their own specific and FIXED aes50 output assignments for each type of output port they possess. So the real key is what you assign in the ase50 output menus. The xlr outputs will simply follow their fixed assignments. XLR outs are fixed to specific aes50 ch’s but the aes50 ch’s themselves are not married to anything, you can freely change them. The Wing can do that 1 by 1 which is very powerful but a bit more tedious.

      XLR’s on the DL/S32 are fixed at aes50a out 1-8 and aes50a out 9-16,

      DL/S16 XLR’s are fixed at aes50a out 1-24 in groups of 8 with the config knob dictating which group is currently assigned.

      Default is aes50a out 1-8
      +8 is aes50a out 9-16
      +16 is aes50a out 17-24

      Input wise the DL32 will shift the S16 inputs up by 32. Aes50 1-32 will be the DL32 inputs and aes50 33-48 will be the S16 inputs
      • Apr 24
    • Wing2021
      Paul_Vannatto Oops, you are correct, my goof.
      • Apr 24