Statistics

261,464 members
140,189 posts
  • jwsandersjr
    Contributor - Level 2
    2020-06-08

    In my quest to learn the X32, I've put the latest version of X32-Edit on my MacBook. This is the 4.x version as I'm running the 4.01 firmware on the board.

    I'm looking for some help with X32-Edit. Simple things like determining "sends on faders" and just changing/editing a scribble strip.

    Can someone point me in the right direction? Did I miss the "help" option in the program?

     

     

    read more...
    0 103
    • jwsandersjr
      Paul_Vannatto


      @jwsandersjr wrote:


      I'm looking for some help with X32-Edit. Simple things like determining "sends on faders" and just changing/editing a scribble strip.





      Sends on Faders (SOF): On the right side you will see the bus buttons - click on one and that will put X32-Edit in SOF for that bus and the far right strip will be the master strip for that bus.


       


      Scribble Strip Editing: Right click the desired scribble strip. At the top of the popup screen, type the name and choose the color.


       


      Help: The best help source is right here. 


       

      • June 8, 2020
    • jwsandersjr
      jwsandersjr

      Thanks, Paul!


      I had just about guessed the SOF function with the BUS buttons on the right, thanks for the confirmation.


      And on Mac, command click on the scribble strip brings up the edit as well.

      • June 9, 2020
  • jofigoco
    Contributor - Level 1
    2020-06-08

    Hello.

    I"ve been watching a lot of youtube videos on the new features of v4.0 and I thought I had everything down. I have the X32 connected to an S32 on stage and I used all 32 inputs and also outputs 1-4 for the wedges and outputs15-16 for the mains. No issues there. With the new v4.0, I tried using the local outputs 13-14 for the rear speakers so I can "time-align" them through the Matrices. I went to user tab, outputs,  chose user 13, matrix 1 and user 14, matrix 2. It worked and everything sounded great until I tried the main fader. The fader would only work for the rear speakers and would not "control" the mains. The sound levels would not change on the mains but I can increase and decrease the levels on the rear speakers. It seems there is something that I'm forgetting to do but I can't seem to put my finger on it. I need help. Thank you.

    read more...
    0 70
    • jofigoco
      Paul_Vannatto


      @jofigoco wrote:


      I went to user tab, outputs,  chose user 13, matrix 1 and user 14, matrix 2. It worked and everything sounded great until I tried the main fader. The fader would only work for the rear speakers and would not "control" the mains. 





      The matrixes cannot be directly assigned to the User Out. They have to first be assigned on the Out 1-16, Aux Out or Ultranet screen, then individually assigned to the User Out. Therefore the taps are determined on those screens (Out 1-16, Aux Out or Ultranet). I would suggest you export your scene to a file and attach it to your next post (Choose File below).


       

      • June 8, 2020
  • Kennyken
    Contributor - Level 1
    2020-06-08

    Musictribe,

     

    I am the sound guy at a local church and I lost 2 channels faders on the X32 mixer without ever touching routing setup or anything of that nature. The channels work but I have no control sliders are not working.  Any help would be great.

     

    read more...
    0 68
    • Kennyken
      GaryHiggins

      @Kennyken 


      Hello, hope you saved all your files before. I would suggest doing that again and then initialize the mixer. Maybe that will set all back to what it should be. I might also try to reload the old firmware and see if the faders work once again with it. It also may be worth downloading the new firmware again and extract the file and trying to load it up another time. EDIT: It would be unusual for a firmware version to cause hardware malfunction. That said I believe there is a new fader version loaded in that particular update and maybe it didn't load up correctly.

      • June 7, 2020
  • jwsandersjr
    Contributor - Level 2
    2020-06-07

    This morning I ran the board by myself. (It was a little bit of a shock as I was unaware that my "teacher" wasn't going to be there today as my safety net, but hey...).

    At some point during the service, I noticed that the "main meters" (Main/Solo meters to the right of the main display on the X32) stopped working. I'm fairly certain that I was seeing activity on those meters earlier during rehearsal, but they definitely stopped at some point. Nothing was impacted by this, still had sound, but it distracted me in that I was trying to find out how to get them back. I'm hoping that someone here can point me in the right direction.

    Also, as a side question, does the version of X32-Edit need to "match" the version of the firmware? I think I may have a V3.x version of X32-Edit and we are running V4.02 firmware.

    Thanks,

    Jim Sanders

    LIVESTREAM ONLY.scn
    read more...
    0 85
    • jwsandersjr
      GaryHiggins

      @jwsandersjr


      You do need the latest version of Edit for firmware 4.02. I don’t think it matches exact numbers, maybe version 4.01 is it?  Otherwise some features are not supported.


       


      Edit: Just checked, It is X32-Edit version 4.01 

      • June 7, 2020
  • MarkSkipper
    Contributor - Level 3
    2020-06-07

    Is RTA display on channels or buses an option yet on Wing? (FW 1.06 as of 6/7/20) 

    Thanks!

    Mark

    image.jpg
    0 84
    • MarkSkipper
      GaryHiggins

      @MarkSkipper 


      Hi Mark, yes it's already there.


       


      Edit: Should have said where! On a ch home or eq screen, there's a little gear type icon up top, center. Tap and set up.

      • June 7, 2020
  • Bvandonkelaar00
    Contributor - Level 1
    2020-06-06

    I have an X-32 as my main console at FOH. I am using an S32 stage box at the stage. We are preparing to livestream as we go back to live services. I purchased an X-32 compact for our video room. 

    I am running a pro-co Ethercon between the X-32 and the S16 AES50 (A port on both side) and I am running another Ethercon cable out of AES50 B port into the X32 compact AES50 A port. I am not getting a signal at the compact. 

    I'm not sure if that is correct, or if I just have to route signal differently. Can anyone help?

    read more...
    0 106
    • Bvandonkelaar00
      Paul_Vannatto


      @Bvandonkelaar00 wrote:


      I am not getting a signal at the compact. 





      Do you have sync between both X32 consoles? Is one set to master clock (sync=Internal) and the other as slave (sync as AES50 port A or B - whatever you are using)? If so, what do you have assigned to the Routing, AES50 B screen on the main console?


       

      • June 6, 2020
    • Bvandonkelaar00
      CraigFowler

      Also, can you clarify your AES50 interconnectivity.  You mention using an S32 on stage, then you mention connecting your console to an S16, using the A socket on both.  Then you mention using the B socket to connect to the Compact.  Is that the B socket on the FOH console, or the B socket on a stagebox (and if so, an S32 or an S16?)


       


      Also, by default the signals to be output over AES50 are those generated by the console and staged in the out1-16 and ultranet tabs, not remote preamp passthrough.  The default input routing for the Compact will be from its local preamps first too, so although your AES50 interconnectivity and clocking may be fine, the routing settings for both consoles will still need to be changed away from the default.

      • June 6, 2020
  • VinnieM
    Contributor - Level 1
    2020-06-06
    To Tech Support. I can't complete my user profile because the required telephone contact area code field does not list my area code. With an incomplete profile, I can't submit a ticket to ask for a solution to this area code problem. And I just signed up, and can't find either direct phone contact or an online help-chat to fix this problem. I don't even know where to go find the answer to this question I'm posing, assuming there's a response. And, without being able to post a ticket I can't get answers to issues I'm having setting up my new board. Please help!
    read more...
    0 53
  • OzzieO
    Contributor - Level 2
    2020-06-06

    Just bought a brand new wing from Pitbull Audio.. opened and it works fine on the board but the screen is terrible.. it keeps ghost touching.. click on one thing and it goes there then immediately goes somewhere else... touches other items on the screen by itself.. sometimes even moves fader without any remote access or anyone touching it.. i downloaded the latest firmware and also re initialized the board.. 3 times..... but it's still happening...its almost as if someone is is also using the board.. anyone experience these randomized ghost screen touches?

    read more...
    0 132
    • OzzieO
      GaryHiggins

      @OzzieO 


      Sorry for your trouble. Yes these type of issues are known to occur on some defective screens. I would suggest you send the Wing back to the vendor and get a total replacement. 

      • June 6, 2020
    • OzzieO
      OzzieO

      Tnx for your response.. are you a behringer rep please?

      • June 6, 2020
    • OzzieO
      Teacee90 I have the same issues screen jumps from screen to screen like a strobe light and faders moving without being touched
      • July 25, 2020
      • Ghost touches
        GaryHiggins It is a hardware issue with the touchscreen. You need to get the board replaced. Use support above and create a CARE ticket to get a replacement.
        • July 26, 2020
      • Ghost touches
        Teacee90 ok thanks will do
        • July 31, 2020
    • OzzieO
      Teacee90 I just talked to the retailer they informed me there were some units shipped with faulty boards, they are sending me out a replacement.
      • July 31, 2020
      • Ghost touches
        GaryHiggins Fantastic. Who was that btw, they seem like a place to do business with!
        • July 31, 2020
      • Ghost touches
        Teacee90 Sweetwater Music they have a 2year warranty no extra fee, and the replacement has arrived and so far so good
        • August 3, 2020
  • AHolland216
    Contributor - Level 1
    2020-06-05

    This is my 1st post on this forum, so please have mercy!

    I have been reading MANY of the threads here but yet have not a clear idea on how to do this.

    This is what I need to achieve:

    (1) at FOH (2) Broadcasting mix, I'm trying to figure out if I can go out of the AES50B into my BC x32, If so what do I need to do to change the routing on the BCx32? How do I set this all up?

    read more...
    0 100
    • AHolland216
      DaveMorrison

      @AHolland216 


      Yes you can. If you are just forwarding the 32 built-in preamps from the FOH console, Set FOH like this:Screen Shot 2020-06-05 at 10.31.29 PM.png


      Set the Broadcast console like this (assuming you're using AES50-A for for input):Screen Shot 2020-06-05 at 10.32.10 PM.png


      Make sure only one console is the master and the other gets its clock from the master (probably FOH-Master).


      These screen shots are from X32-Edit—Highly recommended.


      If you have more questions, just ask.

      • June 5, 2020
  • ryanhughes_
    Contributor - Level 1
    2020-06-05

    I have spent most of the past 2 days trying to get my Pro2 to connect to my MBP through the DN 9630 with no luck. Does anyone have any thoughts on what could be the issue? Is it all routing?

    0 207
    • ryanhughes_
      DaveMorrison

      @ryanhughes_ 


      There are two possibilities. No signal to the DN9630 from the console and No signal from the USB port to your Mac. 


      One common issue on the Mac end is security. The Microphone must be enabled for Logic Pro X (under the Security and Privacy System Preference).


      Can your Mac detect the DN9630's USB connection? Hold the "option" key while opening the Apple menu (). Select "System Information...". Look under Hardware—USB. 

      • June 5, 2020
    • ryanhughes_
      ryanhughes_

      I wont be back over to the church until tomorrow, but I'm pretty sure I am getting connection from DN9630 to MacBookPro. When I open Logic I can select KT-USB as input and output device. If that is what you were talking about. Otherwise, I will check that the connection is secure when I get over there.

      • June 6, 2020
Go to page