Statistics

253,560 members
131,128 posts
  • New
    jaybyname
    Newcomer - Level 1
    2021-09-23

    Morning all, 

    Need some advice on my new TC set up. 

     

    I have a BQ250 and 2 BC208 bass cabs. Am I right in thinking that when connected the overall speaker load becomes 16 ohm, or are the rear unputs on the cabs parallel connectors making the cabs go to a 4 ohm load which perfectky macths the head and wattage.

     

    There is only 1 speaker output on the reverse of the amp so i have to dasiy chain the cabs

    Was reccomended this setup but then thinking connecting 2 8ohm speakers in series makes  a16 ohm load which to my knowledge doesnt really produce its maxium volume potential.

     

    This make sense? Or shoul I have just bought 1 single 4 ohm speaker. 

    read more...
    0 10
    • jaybyname
      RobbyWingfield Hi, jaybyname, this is Robby with Music Tribe. Daisy chaining speakers halves the ohm load collectively. So, daisy chaining two 8 ohm cabs would lower their collective impedance to 4 ohms which will match perfectly.
      • Oct 2
  • New
    percy1
    Newcomer - Level 1
    2021-09-20

    I've forgotten the password for my NX1000D Behringer power amp. I've spent a very long time trying anything that seemed likely but with no success. Is there any way around using the password? What if I update the software?

    0 9
    • percy1
      Nigel67 You will need to connect the NX Series EDIT software to your amplifier. Once connected, go into the Set Up page and you will be able to unlock your unit and set a new password.
      • Oct 3
  • New
    w_hein
    Contributor - Level 1
    2021-09-18

    Hello.

    Bought a new Vortex flanger and connected it to PC (Win 10) and/or Android. Both devices recog. the pedal. I can send artist toneprints to it - that works fine.

    I can not build own toneprints. The software says "connect your TonePrint product to your xydevice..." Well, it is connected - i can send toneprints...

    But i want to create own toneprints. Why is that not working?

     

    Cheers

    Wolfgang

    read more...
    0 8
  • New
    EchoKraft
    Newcomer - Level 1
    2021-09-16

    My display on my deepmind 12 is fading.

    Is anybody else having this problem?

    1 4
    • EchoKraft
      RobbyWingfield HI EchoKraft, this sounds like it could be a hardware fault. Please open a support ticket with a video of the issue so we can determine if your Deepmind needs repair.
      • Sep 18
  • New
    APPART
    Newcomer - Level 1
    2021-09-16

    Bonjour ,

    Est-il possible de régler l'interrupteur pour que le son ne se coupe pas instantanément ?

    0 10
  • New
    SantosAvila
    Newcomer - Level 1
    2021-09-14

    I have a behringer umc 404hd.   sonic cell module whit midi and a keyboard with usb

    how conect this three elements using behringer..

     

    0 2
    • SantosAvila
      RobbyWingfield Hi SantosAvila, this is Robby with Music Tribe. The Roland Sonic Cell is an interface and synthesizer module. In order to use your UMC404HD at the same time you would need to select the UMC404HD as your default audio device. You would then come out of the audio outputs of the Sonic Cell into the UMC404HD. You would then have to have your Sonic Cell as a MIDI device in your DAW in order to send MIDI to it via USB. Lastly, your MIDI keyboard would then be added as a MIDI controller in your DAW. If you require more support please submit a support ticket at the link above, thanks!
      • Sep 18
  • New
    Drpickup
    Newcomer - Level 2
    2021-09-12

    Voicelive 3 Looper full even after deleting some loops help

    0 5
    • Drpickup
      RobbyWingfield Hi Drpickup, this is Robby with Music Tribe. Please empty the trash on the device you have your Voicelive 3 connected to. If you require more support please submit a care ticket on the support tab above
      • Sep 18
  • New
    trowerr
    Newcomer - Level 1
    2021-09-11

    I can update the firmware but I cant get WIN10 to see my folder so I can copy off my loop to be saved on my computer.

    I SWORE I did this before.

    Help???

    0 1
  • New
    peterkirklive
    Newcomer - Level 2
    2021-09-08

    Hi guys, why are my monitor SO LOUD? Cant increase volume more than 2/ 3 what ever way i have them wired. 

    0 1
    • peterkirklive
      john0121 Hi Peter, you need to lower the level of your source material/ pc volume if the speakers are too loud as there isn't any volume control on the speakers for the USB bus.
      • Sep 10
  • New
    Elttut
    Newcomer - Level 1
    2021-09-08

    I have been loving my Neutron but today I turned it on and it would not respond to MIDI controls from my keystep pro. I tried several different midi channels. It will pass a very low pitched sound if I turn the VCA bias up but it seems unable to receive midi. I also tried a basic CV patch (pitch to osc1+2, gate to env 1) and it had slightly better results but still far short of a performable level of control. I attempted the reset process I found online to no avail. Please help! 

    read more...
    0 0
    • Elttut
      ChrisEdwards1 Hi Elttut, I can see you have also submitted a technical support ticket for this issue. Upon checking the ticket I can see a response was sent on 08/09/2021 and is awaiting further follow-up.
      If you do not see this response in your main inbox could you please check your spam/junk folder as we have seen our responses route to these locations on occasion if you are unable to find it please let me know and I will have it resent.
      • Sep 10
Go to page