• New
    than8329
    Newcomer - Level 1
    2020-12-21

    Hi there! My name is Thanos and I'm a sound enginieer-designer and I'm using the midas DP48 personal monitor for three months now and I'm satisfied. The problem is that the musicians need the mute function sometimes because I'm changing the inputs from the midas DL32 stagebox or I'm changing the instruments. Everytime I warn them to turn off the master volume because the mute function does not exist. Is there something better than this??? Is it available a firmware update with the mute function???

    read more...
    0 44
    • than8329
      Paul_Vannatto Hi Thanos, the mute function is on the wishlist. No ETA at this point.
      • December 21, 2020
    • than8329
      joshtew I am facing this problem too!

      With default routing method of direct out connections from channels to AES50, muting the channels on the mixer doesn't mute any of the personal monitors nor analogue outputs from Hub4. I have stage monitor speakers connected to Hub 4 analogue outputs and this is sending the pop from cable connection/disconnection straight through!

      Will be helpful to have the option of tapping from "IN/LC +M" tap point.

      Will a feasible workaround be to send the guitar channels through P16 segment tapped from channels at "IN/LC +M" tap point?
      • December 26, 2020
      • DP48MUTE FUNCTION
        MichaelIvey Well Joshua another solution to this dilemma until it's an actual update from Midas would be to use a suggestion that resolved the issue "DP48 Playback for mixing IEM" used. What was suggested was making a LIVE A Snippet and a PLAYBACK B Snippet. The LIVE A Snippet can serve as the boards routing when Performing, Shows, and Recording. The PLAYBACK B Snippet could serve a dual purpose. Not only to route the card signals back thru AES50B for the DP48 but also since none of the LIVE A Input Channels are connected the board nor the speakers nor the IEMs will pass thru the "POP" because it's not routed.
        • Jan 4
      • DP48MUTE FUNCTION
        joshtew I opted to go P16 route as we may need to mute these instruments mid programme and there is no need to re-train our many volunteers sound engineers on what to do when they need to mute the instruments.
        • Jan 29
  • New
    vichaipart
    Newcomer - Level 1
    2020-12-21

     

    Please advise on the replacement model for both DL441 and DL442.

    0 40
  • New
    korikomi
    Newcomer - Level 1
    2020-12-20

    Just wondering if anyone else has experienced not being able to connect remotely to the console after updating to iOS 14? It works on another iPad that's still running 9.3.5 but it was also working fine on 13 before updating.

     

    console is the Pro 1

     

    Thanks!

    read more...
    0 7
  • New
    TNTSound1620
    Newcomer - Level 1
    2020-12-17

    As a Dealer/Distributer I've been left in the dust as to how future orders can be made. Is the only option to purchase from big internet stores like amazon? If so this is unfortunate as so many dealer/distributers have spent years implimenting them into businesses and HOW to build up your sales to then just be left behind and not be able to provide support to our customers is a huge slap in the face. I'm looking for a real system and solution for ordering Behringer/Midas products to support my customers.

    read more...
    1 27
    • TNTSound1620
      KyleJohnson Hi James, Kyle here with Music Tribe. Please contact us through the Support portal at the top of the page so that we can get you in contact with the right people.
      • December 18, 2020
  • New
    GregWarren
    Contributor - Level 3
    2020-12-17

    Hello,

    I have 6 DP48s and have 2 Hub4s being shipped as we speak.

     

    My question, will I need 6 ethernet cables from the 2 Hub4s to each of the DP48s to power them (PoE) OR can you use 1 ethernet cable from the hub4 to the first one and then daisy chain them and get power to them without having to use the ac adapters?

    read more...
    0 50
    • GregWarren
      Paul_Vannatto Hi Greg, if you want PoE, you will need 6 cables. The Thru AES50 jack on the DP48 does not supply the PoE, similar to the P16-M.
      • December 17, 2020
    • GregWarren
      GregWarren Okay...thanks...now how do I setup the IEMs with the hub 4s? What ports on the back do I use?
      • December 17, 2020
    • GregWarren
      Paul_Vannatto Looking at the back, from right to left are the ports outputs (1-4), mix A and B. Ports 1 and 2 mix A are XLR and the rest (port 1/2 mix B and all of port 3/4) are 1/4" TRS. You also need to enable each port output by pressing on the respective port button on the front panel (just below the Port 1-4 label).
      • December 17, 2020
      • Midas DP48 & Hub4
        GregWarren Ethercon shielded 5e or 6a?
        • December 18, 2020
      • Midas DP48 & Hub4
        Paul_Vannatto Hi Greg, shielded cat5e is getting harder to find here (in Canada). I have a mixure of shielded cat5e, cat6a and cat7. Anything that works between Behringer/Midas consoles and stageboxes should work with the Hub4 and DP48.
        • December 18, 2020
    • GregWarren
      MichaelIvey Hey Douglas. I feel your frustration as I did the same method you did and got the same results time after time after time. But here's what changed. Instead of saving the file in Excel where I created it I saved it to my Desktop. When given the option of the format to save it in I selected CSV UTF-8 (Comma delimited) (*.csv) again saving the file to my Desktop. Hope this works for you.
      • December 19, 2020
      • Midas DP48 & Hub4
        Paul_Vannatto What has this to do with our discussion here about the Hub4 and DP48?
        • December 19, 2020
  • New
    rgalv001
    Newcomer - Level 1
    2020-12-17

    How can I get a multitrack track live recording using an SD Card in slot 1. I tried but only a single .wav file records. Then it will not open on my Mac. I need help step by step. Couldn't find on manual. I am able to record on a flash drive in stereo, but would like multi-tracks so I can mix in Logic Pro.

    read more...
    0 30
  • New
    slowstar1
    Newcomer - Level 1
    2020-12-16

    Please, help me to order Fire Wire card for my Venice F32 mixer, it is broken and I need to replace it ASAP, your help will be much appreciated!

    Sincerelly,

    Slobodan Markovic,

    [email protected]

     

    read more...
    0 33
    • slowstar1
      Dale_M Dober dan Slobodan, you simply need to go to the above tab, hit support, +create a care ticket, then drop-down to Spares -from here simply ask for price & availability of Q09-AD600-41000 (VeniceF32 Firewire PCB T-VN214C-02) I hope this helps.
      • December 24, 2020
  • New
    ZackMorris
    Newcomer - Level 2
    2020-12-15

    Hello! I am looking at a used Midas XL8 digial console system for an install. I have not set up a XL8 before and it looks like all of the AES50 ports on the routers (DL461) and all of the AES50 ports on the control surface have redundent AES50 ports. An X port and a Y port. We use 2 KT DN9650s in our set up. One for USB and one with a MADI card... they do not habe redundent AES50 ports... with the XL8 am I fine to just connect to the X OR just the Y AES50 port or will it only work with I/O with redundent AES50? 

    Thanks! Zack Morris 

    read more...
    0 20
  • New
    rwpotter
    Newcomer - Level 1
    2020-12-14

    As a keyboard player who is also running the monitor and FOH mixes.  I'm looking for an easy way to turn the vocal effects OFF while the lead singer is speaking, and ON while he is singing.  Can I map this to a button on my keyboard or to a footswitch somehow?  I see that the MR18 has a midi IN and OUT but I am uncertain how to obtain the desired mapping.  

    read more...
    0 41
  • New
    TroyKrueger
    Contributor - Level 2
    2020-12-13

    Hi, could someone confirm on a midas M32, firmware 4 or above that you can store a snippet with the master L/R fader at 0.0 and when it is loaded it puts that master fader back at 0.0?

    I'd really appreciate it. 

    Cheers, 

     

    Troy

    read more...
    0 22
    • TroyKrueger
      Paul_Vannatto Hi Troy, I just tested a snippet to zero Main LR on both the X32 and X32-Edit and it works file. What version of firmware 4 are you using? Make sure you have updated to the latest (4.04). Also make sure you don't have any snippet safes enabled.
      • December 13, 2020
      • M32 Snippet to store L/R Master Fader Level - doesn't work?
        TroyKrueger Thanx Paul, I’ll update the firmware (it’s currently 4.02 or 3... not there now- but it’s not 4.04 for sure) and report back. I can also confirm there are no safes enabled and also that a snapshot also does not change the master fader . Cheers
        • December 13, 2020
      • M32 Snippet to store L/R Master Fader Level - doesn't work?
        Paul_Vannatto The Wing uses snapshots (which are similar to M32 Scenes). I thought you were using a snippet. If you export the snippet to a file does it look like this?

        #4.0# "Main to Zero" 0 0 0 0 1
        /main/st/mix/fader +0.0
        • December 13, 2020
      • M32 Snippet to store L/R Master Fader Level - doesn't work?
        TroyKrueger I will check the snippet I have, in the mean time I can confirm that even after updating firmware to 4.04, when storing a snapshot with the master fader at 0, recalling that snapshot does not restore the master fader to 0, and confirming that there are no 'safes' or 'ignores' in the settings.
        • December 30, 2020
      • M32 Snippet to store L/R Master Fader Level - doesn't work?
        Paul_Vannatto Hi Troy, as I mentioned before, snapshots are not part of the X32 terminology. It saves/loads scenes and snippets. I can assure you that the snippet I provided does indeed move the Main LR master fader to 0 db.

        One other thing to clear up, 0 db is the setting about 2/3 the way up on the fader, not all the way down. Hopefully that is what you are referring to.
        • December 30, 2020
Go to page