Statistics

216,312 members
89,521 posts
  • guitarman_nebr
    Contributor - Level 1
    2019-06-26

    Hey all,

    I have been using the IP2000's for a few months now.   They sound great....until I have to push them for a bit more volume.  I have a small band with pre recorded tracks for Bass and Drums...we sing and play guitar over these tracks.

    I seems there is a general agreement to set everything on the speakers DSP to "0" to use these as a PA speaker with a mixer.   However, it seems there is not a clear explaination as to how much input to use to optimize the output of the speaker.  

    The ouput runs hot and pegs out very quickly...to the point the system will cut out or clip.  I think Turbosound should do a video addressing input and output settings.  On the DSP display it will show the input at two bars and the output quickly goes off the scale.   It is hard to balance these two settings.  

    Does anyone have their own experiences to share?

    read more...
    0 249
  • dhsherbert
    Contributor - Level 1
    2019-06-25

    Hello!

    I just purchased a Turbosound iP300 and had a question that is not addressed in the Quick Start Guide. I'll be using this speaker with my Laptop, Audio Modeling SWAM Wind Instrument software, EWI5000 and Focusrite Scarlett 2i2 Audio Interfacel. I need to use both Left & Right output signals from the Focusrite. Is it OK to use both Inputs of the iP300 for this?

    Thank you,

    Doug

    read more...
    0 139
    • dhsherbert
      KenMitchell

      Hi Doug ( @dhsherbert ), 


       


      Sorry no one replied to you earlier.  I just stumbled upon this when I was looking at your reverb question.  Yes, there's no issue with connecting to both inputs on the IP300 at the same time, whether it be from the same interface of different interfaces.


       


      Hope this helps, 


      Ken


       

      • August 13, 2019
  • JulienRutyna
    Contributor - Level 1
    2019-06-11

    Bonjour,

    Je possède depuis 1 an 2 ip3000, j'ai deja eu 2 retour de garantie car une colonne s'est arreté d'un coup en pleine soirée. L'ecran reste allumé, les fonctions sont accessible mais aucun son ne sort.
    Aujourd'hui j'ai encore un probleme avec des coupures de son de 2 secondes toutes les 3 minutes sur une colonne.
    Je ne comprend pas cette enorme manque de fiabilité pour une marque comme Turbosound surtout que je fais attention a mes volumes d'entrée , j'ai lu sur les forums que c'est un soucis recurrent sur ce modele. Que puis je faire pour ne plus avoir de soucis car j'aime beaucoup ce modele qd il fonctionne.
    Merci beaucoup

    read more...
    0 101
  • Dae_dalus82
    Contributor - Level 1
    2019-06-10

    I own 2 15 inch siena tsp152-ans.  I was going to buy a pair of 12 in loudspeakers but before i do i was wondering the differences between the siena, nuQ, and athens product lines.  The athens have different dispersion options but other than that i am unsure what their main selling points are.  If i go by frequency response and max spl then the sienas are the best bet.  The other two lines are more expensive and i wonder why that is?  Thanks for any help anyone can provide.

    read more...
    0 196
    • Dae_dalus82
      GaryHiggins

      @Dae_dalus82 I cant speak to all the exact differences but when I looked (at turbosound in general) a while back, some models that had the ultranet port, did not include an ethercon port with it. I know the enclosre on some models differed in materials used and would suspect the speakers and perhaps the on board amps are different in some key ways.

      • June 16, 2019
  • robykock
    Contributor - Level 2
    2019-05-23

    Hi I am helping a customer but not sure the proper mounts to use for the IP300 to hang them or suspend them from wall.  What is best practice for doing this?

    Robert

    [email protected]

    0 108
  • JasonChambers
    Contributor - Level 2
    2019-05-20

    I have 2 IQ15's that are less than a year old and really haven't had much use.

    At Saturday's show one of them after being powered on for about 3 minute and without any load shows "over temp" on the display and stops audio output.

     

    Contacted the point of sale and it's a 4-6 week turnaround for repair, which is very disappointing indeed.

     

    Anyone else had this issue?

    read more...
    0 185
Go to page