When I monitor "LR+M/C" in my X32 compact's Monitoring/Headphone section, if I pull down the Main Fader (LR), I still hear everything. Is this a bug? I see the "LR AFL" option (which I believe is the factory default), but I want to hear the Mono Bus alongside the LR Mix because I run a Comm system return through an X32 channel feeding *only* the Mono Bus, so it is in my headphones but not present in the actual (LR) broadcast mix. Monitoring LR+M/C in my headphones, I also cannot not hear the Stereo Limiter (inserted on the LR) having any affect when inserted on my LR Mix. Some colleagues suggested that I had my LR tap point wrong, but I can confirm it it Post Fader. So either this is a bug, or... should I be requesting a "LR+M/C AFL" headphone option?
Can anyone confirm if this is normal/expected and any workarounds to what I'm trying to accomplish? Thanks
Hi all,
I've been experiencing an odd issue with my new Behringer Studio L. It could be my fault, but I was hoping for some guidance from the community if not.
Audio is feeding into the input channels when playing back audio using the USB source. This creates a feedback loop rendering the device useless for overdubs.
I've submitted a support ticket but wondered if anyone else experienced this issue?
I'd appreciate any help!
-Chris
Hi there!
I have a problem with one channel of fp10000 - CPL red led staedy on with no audio present on input and no loudspeaker connected.
I tryed if it still works and it do, but significantly lower level. red led goes on few seconds after powering.. fan does not go in high speed.
Any ideas? thaks for reply!
BR, Damir
Our church recently was victim to a lightning strike. After troubleshooting, it appears we are not getting any signal from the SD8 stage box. The power light is on but no communication between the X32 compact and SD8. I eliminated the possibility of the CAT5e cable being bad.
Is there anyway to switch from Port A to port B on the SD8 and see if it works? This is the only stage box we use. If so, what needs to be switched on the X32?
Hope someone can help me here. I have purchased the podcastudio usb kit and there isn't any software with it, even though the booklet says there should be. I have been on line and have no idea what I am supposed to download. The direct website says I don't need software as it is plug and play, but the system doesn't plug and play. Any suggestions are greatly received.
Uploaded new 21 firmware
Had on there the New Pitch control I've never used this effect an not sure how to operate.
Is there any file/paper work on how to operate that on the console on a channel.
Hello all,
I have two doubts about DCX2496 and I hope you guys can gimme a hand.
1 - How can I update the unit firmware securely. It´s not mentioned in the user manual as far as I got to see.
Already tried to Google it, but didn´t find anything that could help.
2 - I need to configure this unit to feed 5 two-way active speakers (not 5.1, it will be 3 front speakers LCR and 2 LR in the back delayed), plus a pair of subs. I don´t need the xover feature (all output must be fullrange once the speakers already have their own crossover processing), I´ll just need dynamics and delay features to setup the system. I did not see it in the manual, is it possible? Or should I extend the all filters settings from 40 Hz to 16 KHz manually?
Thanks in advance for some tip.
Hi team,
Wondering if any of you smart people would be able to help me out.
We have a school production coming up soon and I want to run multiple outputs from QLab. We don't have a good soundcard so I figured I would use the USB Card in the back of our M32...
Is there a way for me to send my CARD inputs (coming into the M32 from my laptop) to the X32C side stage (being used for monitors).
I thought this could have something to do with the fact that AES50 is 48x48? Currently IN 1-16 for both consoles are coming from the X32C (wless mic recievers) and IN 17-32 are coming from a DL16 on a separate AES50 line for the band.
Thanks!
Can anyone help to why this wonderful mixer I just found out after not understanding during a show why it was behaving like this it seems the two mono channels we are given only one of them is actually sending to left and right. Channel 9/10 when plugging into the mono L input sends perfectly to left and right side… But channel 11/12 which is exactly like channel 9/10 is only sending to the right side?
So I recently got a X18 from Reverb and when i got it, everything was working fine. As i started to build my IEM rack system I figured i should run an external router to get a stronger signal...this is where things began to take a turn. I got the router set up and then magically i started getting no input signal at all. I've tried literally everything. Resetting everything, turning things on and off, trying the Ipad or the laptop. updating firmware, different inputs. The faders arent getting any signal at all. when i plug the IEM transmitters into the AUX and turn the X18 of i hear a pop so that is getting signal, but nothing else. Someone please help lol. I've checked all my routing. it seems to be locked in. I'm just so confused as to what is going on.