Statistics

298,839 members
182,512 posts
  • New
    toszny
    Newcomer - Level 1
    2022-09-21

    Hello.

    Form a couple of days I'm trying to make work correctly TC G-System with Taurus SH5 Stompbox.

    Taurus needs a momentary shortcircuit between:

    1. tip and sleeve on port 1 for clean channel

    2. ring and sleeve on port 1 for crunch channel

    3. tip and sleeve on port 2 for lead channel.

    I understand than G-System cannot do momentary switching, only latching.

    But it is not the strangest thing: when I couldn't establish right behaviour of the amp, I tried to find the explanation. When I used a electonic multimeter on jacks installed in SW1 or SW2 (beep test  between tip, ring and sleeve) i've noticed that setting in G-System configuration like "0000" gives shortcircuit beetwen right parts of plugs, and "CCCC" makes all internal contacts open!

    It is right  in oposition with the product manual (and logic), where is written that "C" means closed contact and "0" means opened.

    The order of contacts on screen is not logic too: R2 T2 R1 T1, for example CCC0, in reality means that on SW1 tip and sleeve are shortcircuited, and other relays are opened.  

    I know that all which was written could is strange, expecially with such pro equipment from TC Electronic.

    Is there anyone who knows this problem? How get an explanation about this "reversal behaviour" - witch comparison to the manual?

     

    read more...
    0 3
  • New
    vicmusiker
    Newcomer - Level 1
    2022-09-21

    Hello, anyone can help me find this MCU Board for Midas M32? The part number is A09-B3I00-23000. The mixer was damaged by a lightning that came via ethernet cable 5 months ago. And since then we are waiting Music Tribe Factory to send the part to the Service Center. No sign or estimated date of arrival....

     

    Thank you

     

    Victor

    read more...
    0 7
  • New
    claudioscas
    Newcomer - Level 1
    2022-09-21

    Olá,

    Estou com o seguinte problema: Eu utilizava somente uma guitarra conectada e não tinha um microfone condensador, então, adquiri um recentemente e ao ativar o botão do phantom power, notei que os leds do microfone "SIG" e "CLIP" ficam acesos constantemente e o microfone não funciona e em alguns vídeos que vi sobre a umc22 isso não deveria ocorrer.

    read more...
    0 5
    • claudioscas
      Dale_M Use a different XLR lead, use another condenser mic and see if the fault stays with the unit, if you still need support please go to the Support tab above and submit a Technical ticket so we can assist you.
      • Sep 21
  • New
    muzikgeye
    Newcomer - Level 1
    2022-09-21

    Hello. I am attempting to connect the Xenyx Mixer 302 USB to my desktop computer that utilizes Windows 10. After conecting my stereo system to the Mixer, through the Line Input and the 2 Track Input, I conected the Main Mix output on the Mixer, using RCA cables, directly into the back of my computer, through the Line In jack. I am attempting to record the sound onto my Audacity program. With this set up, everything works fine. Except for the fact that there is a lot of noise combined with the sound from the Mixer, which I have concluded is caused at the connection point of the Line In jack connection on back of my computer. So, in an effort to eliminate noise, I purchased an RCA to USB cable, which I have connected from the Main Mix Output to the computer. Now my computer is unable to locate the Xenyx Mixer 302 USB. So, am I not able to use the RCA to USB cable, or must I have to download a program in order to record from the Mixer. Thank You.

    read more...
    0 2
    • muzikgeye
      Dale_M This will cause a conflict as the computer is likely seeing the RCA to USB as another sound source, you would be better to try your original working set up on a different DAW or even better a different computer to see if the noise follows the 302 or goes on the new connection.
      • Sep 22
  • New
    orpheus70
    Newcomer - Level 1
    2022-09-21

    Ayuda por favor!!!como conectar a ordenador!!!He probado con 2 ordenadores diferentes.......nada.....todo igual

    read more...
    1 4
  • New
    cashappscontact
    Newcomer - Level 1
    2022-09-21

    Cash App is one of the greatest payment platforms in the US which is used by millions of people. Many Cash App users want to delete Cash App transaction history but please note that Cash App is end-to -end encrypted and 100% safe so you do not need to worry. Cash App does not allow its users to delete Cash App transaction history. In case you still want to do that then you need to delete Cash App account to remove everything.

    read more...
    1 1
  • New
    subman56
    Newcomer - Level 1
    2022-09-21

    I have tryed to get this K2 to function. I have fallowed youtube videos as well as the Quick start Guide. I am using the Arturia
    Midi keyboard with this unit. but have been unable to get the unit to work.

    0 3
  • New
    SteveLynch
    Contributor - Level 2
    2022-09-21

    I have an ungodly stable of Turbosound IQ speakers, and I love them dearly.

    I do however own a bunch of RCF 8006 subs, which I also love.

    I've become quite fond of the flexibility, and ease of being able to run a vast speaker matrix over Cat-5 at something like an air show, or a road race, or whatever. It also makes delay so damn easy!

    I'd really love to be able to throw My subs into the mix using the same network. 

    Is there any product in the roster that any of y'all can think of, that can be used to deliver analog input to a powered sub, using only the ultranet network?

    I suspect I could make a P-16 work, but I can't believe they don't have something like one of the little power play units that you can just plug into the back of a speaker, powered monitor, or whatever, to feed audio via ultranet.

    Is there a product I'm overlooking that would fit the bill?

    Is ther an official forum to try to make a case for development of a new product if not?

    I just got My wing, and I know there are Dante devices, but that'd be a pretty hefty expense to avoid the relatively small inconvenience of hauling  hundreds of feet of XLR cable.

    Thanks for any and all input y'all!

    read more...
    0 3
    • SteveLynch
      Paul_Vannatto Hey Steve, you could use the new Midas DN4816-O, which has both In and Out Ultranet ports.
      Here is a video that shows how it works (please forgive the camera work and the language, its not my video)
      https://www.youtube.com/watch?v=K8RR6TGmmww

      Another option using the Wing, you can use the StageConnect port at the back of the Wing to connect to the DN4816 to have both XLR-M out and Ultranet out.
      • Sep 21
    • SteveLynch
      GaryHiggins Klark Teknik DN 4816U if you have a Wing, SC to SC. $200 gets you ultranet out to your speakers. It also is a swiss army knife for a ton of other uses. Think that could do what you want (besides Paul's suggestions)
      • Sep 23
  • New
    Jesuton5
    Newcomer - Level 1
    2022-09-20

    Hi all, 

    I have not been able to find any definitive instructions for midi program changes to link my VoiceLive 3 Extreme to my Widi Master. 

    Midi signals are definitely being sent by Bandhelper, confirmed by Midi Log. 

    The Widi Master is definitely receiving the Midi signal, confirmed by blinking LED. 

    The Widi Master also blinks when I press buttons on the VL so not a Widi Master issue. 

    Midi Wrench also confirms that the Midi signals are being sent and received by Widi Master. 

    The only thing left to really double check are the Midi Program Change Values I put in.

    I've only been able to find instructions on message boards and YouTube videos so it's a bit frustrating to be honest, and difficult to pinpoint what the issue could be. 

    Here's an example of what Midi signal I'm  sending to change the VL3X preset:

    EASY ON ME - Preset number 257.
     
    I therefore entered:
    BANK MSB 0
    BANK LSB 2
    PROGRAM 0
     
    I also tried 
    BANK MSB 000
    BANK LSB 002
    PROGRAM 000

    ... but the preset still doesn't change.

    Would appreciate any assistance with this! 

    A link to official instructions or a bunch of examples cos I'm out of ideas!

    Thanks very much.

     

     

    read more...
    0 7
    • Jesuton5
      PedroRodrigues Hi Jesuton5, thank you for your post, please ponder that the MIDI implementation in VL3 is essentially the same as the VoiceLive 2…
      There can be up to 500 presets loaded into a VoiceLive 3, and it’s possible to navigate between these presets with an external controller sending MIDI Control Change (“CC”) and Program Change (“PC”) messages. The VoiceLive 3 can receive CC and PC messages via MIDI from sources like keyboards, footswitches, DAWs, and more. For the controlling device to send a MIDI message to VL3 it needs to be using the same MIDI channel as the VL3, typically this is channel 1 but you’re welcome to change it.
      Also make sure you aren’t misusing the MIDI input filters and ensure that the MIDI input is set to be either “USB” (for the USB-mini input) or “MIDI Ports” (for the 5-pin MIDI input) depending on how you're connecting. These settings can be changed in VL3’s “Setup” menu, on the “MIDI” tab.

      To change Presets via MIDI, first tell the VL3 which Bank to look in, then tell it which Preset in that Bank you want to change to.
      Bank select: To specify the desired bank, issue an LSB Bank select message (CC#32) with a value of 0-3.
      Preset Select: After specifying the Bank, issue a PC Preset select message with a value of 0-127.

      MSB LSB VL3Bank Program Change (PC) VL3 Preset #
      0 0 0 0-127 1-128
      0 1 1 0-127 129-256
      0 2 2 0-127 257-384
      0 3 3 0-115 385-500


      The internal number associated with a Preset isn’t exactly what you see on the VL3’s screen, they’re actually all off by 1. This is because internally the list of Presets actually starts at an index of 0. This means that 0 = Preset #1, 1 = Preset #2, 2 = Preset #3, etc. It’s like your presets are saved from 0-499 but are displayed as 1-500.

      There are 4 Banks in VL3, and each Bank contains 128 Presets. Therefore the Preset selection number that goes to VL3 needs to be between 1 and 128. So for a Preset above 128, you need to subtract the number of the first Preset in the same Bank to get the MIDI Program Change info.

      The 9-digit message for changing to a preset is in the format of:

      MSB LSB PC#
      Or, you can first send a CC#32 of the Bank you’re looking in, then a PC value of the Preset you want.
      Here are some examples:
      Preset #5 would be: 5 - 1 = 4
      000 000 004
      or CC#32 value 0, then PC 4
      Preset #100 would be: 100 - 1 = 99
      000 000 099
      or CC#32 value 0, then PC 99
      Preset #208 would be: 208 - 129 = 79 (because Preset #208 is in Bank 1, which starts at Preset #129)
      000 001 079
      or CC#32 value 1, then PC 79
      Preset 259 would be: 259 - 257 = 2
      000 002 002
      or CC#32 value 2, then PC 2
      Preset 322 would be: 322 - 257 = 65
      000 002 065
      or CC#32 value 2, then PC 65
      Preset 491 would be: 491 - 385 = 106
      000 003 106
      or CC#32 value 3, then PC 106
      Preset 500 would be: 500 - 385 = 115
      000 003 115
      or CC#32 value 3, then PC 115

      When you try to address a Preset that does not exist (either an empty spot or one outside the 1-500 range), there is no built-in warning system, VL3 just won’t do anything. So if you can see the “MIDI” indication on the VL3 appearing when you send commands, but are not getting the Preset to change, ensure you’re not referencing an empty or non-existent Preset location.

      If that all seems too complicated for you, consider using Steps instead of Presets. Steps are essentially Presets within a Preset, and you can have up to 10 Steps all in the same Preset. If your current Preset contains the Steps you’ll be using, it just takes a single CC message to choose your Step…
      CC 115 = Step
      Value represents Step Number, i.e. 1 = Step 1, 2 = Step 2, etc.
      So sending a CC#115 with a value of 2 will take you to the second Step in your current Preset.

      Sources:
      https://kb.musictribe.com/musickb/view/article/tch/en_US/VoiceLive-3-Selecting-Presets-and-Banks-via-MIDI-228155247

      https://www.sweetwater.com/sweetcare/articles/6-what-msb-lsb-refer-for-changing-banks-andprograms/

      https://forum.musictribe.com/showthread.php?14591-Midi-PRESET-Change&highlight=voicelive+preset+change+midi

      https://forum.musictribe.com/showthread.php?15866-Voice-Live-3-Set-List-Maker-on-iPAD&highlight=voicelive+preset+change+midi

      I hope this helps.

      Thank you
      • Sep 20
    • Jesuton5
      Jesuton5

      Hello Pedro, thanks for your response. Your message is a copy of one made by you elsewhere on this message board, and actually the only instructions I was able to find. This to say that I have yes attempted to follow these instructions but have not been able to make them work. Would you be so kind as to check the example I gave of preset 257 and show me what it should in fact be, and let me know where I'm going wrong? This is
      of course for Program Changes. As for the Command Changes alternative, there are only two fields to fill in on Bandhelper ('controller' and 'value') but your instructions above include three pieces of information, (eg CC#32, value 3, PC 115) so please clarify this also if possible please. Finally, I am unable to use steps as I have created individual presets for backing track playback, this is the basis of my show. Looking forward to hearing back from you. Thanks P.S As another user also alerted,the links at the end of your response no longer work. Best wishes

      • Sep 21
    • Jesuton5
      kiskadar69 @Jesuton5: read pages 151-152 of the TC-Helicon VoiceLive 3 Reference Manual. On the VoceLive 3 SETUP / MIDI tab: set the Source parameter, set the Input Channel to 1 (because I see that BandHelper sends on channel 1), and set the Input Filter parameter so that VoiceLive 3 filters out neither CC (Control Change) nor PC (Program Change) messages.
      I'm not familiar with the BandHelper program, but the messages it sends seem to be correct.
      • Sep 21
    • Jesuton5
      Jesuton5 Hi @kiskisdar69, thanks so much for your reply and for your suggestions! Yes I can confirm that I've definitely reviewed those pages. INPUT channel has always been set to 1. OUTPUT Channel is also set to 1, is this correct? I have also tested setting to 2. And yep, INPUT and OUTPUT Filters definitely set to NONE. Still no joy sadly.
      • Sep 21
    • Jesuton5
      kiskadar69 Jesuton5: test WIDI Master MIDI Out and VoiceLive 3 MIDI In separately. For testing, get a notebook/computer with a reliable USB-MIDI interface (or ask someone who has one).
      1. Connect the MIDI Out of the WIDI Master to the MIDI In of the notebook and monitor the MIDI messages coming into the notebook.
      2. Connect the MIDI Out of the notebook to the MIDI In of VoiceLive 3 and use the notebook to send Bank Select MSB, Bank Select LSB and Program Change messages.
      • Sep 22
  • New
    abily1
    Contributor - Level 1
    2022-09-20

    I purchased 4 of these speakers on March 22, 2022 and 3 of them have compression drivers that are bad.  I must assume a bad batch as I have never overpowered, overdriven or pushed anything other than vocals through them.  They are being powered by a QSC PLD4.2 which is the perfect compliment to them.  I have had lterally hundreds of speakers over the years primarily EAW but more recently JBL.  I have had Turbosound, EV and even a set of QSC.

    Anyway, 

    I opened a ticket for spare parts not even trying to deal with warranty repair as I expect that to be hell and a finger pointing exercise.  I asked what is the compression driver used in these and where can I order them.  No one has responded so I am stuck...  Does anyone know what the driver model is its no where listed on the driver itself or in any documentation.

    Shame on you Turbosound, I would expect this type of support from Berhinger but damn come on its not like I am asking for much here and I am stuck with gigs lined up.

     

    read more...
    0 2
    • abily1
      Dale_M Thanks for your post. If you bought these and you are having issues with them you would normally raise a Technical ticket so we can assist you, if they are new and you still have your proof of purchase invoice then the warranty will cover getting these items repaired so there is no need to create a Spares ticket. Can you advise your spares ticket number so we can intercept the case?
      • Sep 21
    • abily1
      abily1

      Re: Case CAS-624275-W8J8Q5  -  NuQ102 - purchased 4 NuQ102 on 3/21/2022 

      • Sep 21
    • abily1
      abily1 Attached is my receipt from Musicians Friend. I will get the serial numbers from each one when I get home.

      Turbosound_Order_2022.pdf
      • Sep 21
Go to page