Statistics

240,761 members
116,968 posts
  • New
    PackRuss13
    Newcomer - Level 1
    2021-07-13

    Is there any way to escalate to Lab Gruppen. We have been waiting since January for a client's repair on a Lab Gruppen E5:4 amplifier. We keep getting told the parts are on back order. 

    0 6
    • PackRuss13
      KyleJohnson Hello, Kyle here with Music Tribe. I am going to send you a direct message here on Community so that I can gather your case details and look into this for you.
      • Jul 13
  • New
    Abdallah
    Newcomer - Level 1
    2021-07-09

    Hello,

    can i ask about the availablity of some spare parts related to LabGruppen Amplifier on this window?

    0 11
    • Abdallah
      DavidKnighton Hello Abdallah,
      For spare parts information you must submit an inquiry via the SUPPORT tab at the top of the page.
      • Jul 9
  • New
    Sales1
    Newcomer - Level 1
    2021-07-07

    Hello

    I need to get pricing and stock availability on Lab Gruppen amplifiers can anyone help???

    0 23
    • Sales1
      Nigel67 Hi Sales1. Pricing and availability is only available from our superpartners. Please contact the one closest to you by clicking on this link and selecting the Country you reside in. Many thanks

      https://www.labgruppen.com/buy.html
      • Jul 7
    • Sales1
      Sales1

      Thanks Nigel - no of the 'superpartners' listed on this link supply the E series range.....

      • Jul 7
      • Pricing
        Nigel67 I am very sorry about this. I will pass the link on for this conversation to one of our Availability Team and ask them to advise the nearest reseller to you. Can you advise in which Country you reside. Many thanks
        • Jul 7
    • Sales1
      Sales1

      **none** of the 'superpartners

      • Jul 7
  • New
    hiswkf
    Newcomer - Level 1
    2021-06-23

    Good morning, I was wondering if it was possible to convert an older LGFP14K from US mains to EU mains? If so, what would that entail?

    0 12
    • hiswkf
      DavidKnighton Hello hiswkf,
      Check the voltage spec on the rear panel near the mains input. If it does not specify operation up to 230V, then I would say not possible, at least not without some involved modifications.
      • Jun 23
  • New
    Djgatos
    Newcomer - Level 1
    2021-05-13

    Hi I have a question I have 8 of this line array.      

     

    https://www.seismicaudiospeakers.com/products/passive-2x10-line-array-speaker-with-dual-compression-drivers

     

    Question how many pd3000 any for my 8 line array somebody can help me please ...

    read more...
    0 55
    • Djgatos
      DavidKnighton Hello Djgatos,
      The SA cabinets are 16 Ohm and require about 1,200 watts per cabinet. By running multiple boxes in parallel, you could get 4 cabinets down to a 4 Ohm load, however the power requirements for that many speakers would far exceed the PD3000 power output. You would need an amplifier that could achieve 5,000 Watts @ 4 Ohms so it could properly handle the peaks. The PD3000 produces 1,500 watts per channel, and does not appear to be a bridgeable amplifier, so 1,500 watts is your absolute maximum output @ 4 Ohms. The amp that I would recommend would be the PLM12K44, which can deliver 3,000 Watts per channel at 4 Ohms, or you could bridge for effectively double the output power, which is what I would suggest for these speakers. You would need a single PLM12K44 amplifier to adequately power all 8 boxes in a standard stereo L/R configuration. Not including the subs mind you.
      • May 13
    • Djgatos
      Djgatos

      My Sa audio cabinets I switched the wire to 4ohms each cabinet you think 1 amp can handle 2 boxes 1 each side?

      • May 14
      • Pd3000 lab gruppen power amp
        DavidKnighton At 4 Ohms, the amplifier will deliver up to 1,500 Watts per channel. If you chain two cabinets at 4 Ohms each, your load ends up being 2 Ohms on the amp, which ends up producing less watt output, about 1,000 Watts. I would recommend. In this case I would suggest 1 amp channel per box, which means you'd end up running quite a bit of cabling. I'm not sure how the power requirements change as you switch the cabinet to 4 Ohm load. Maybe you can switch it to an 8 Ohm load, I think that would be better, because then you could chain 2 cabinets for a 4 Ohm load. The amp will perform the best at 4 Ohm loads.
        • May 14
    • Djgatos
      Djgatos

      Ok I'm going to tried working with 2 cabinets with 1 amplifier and we go from there thank you for you help beacuse I'm going to buy 4 pd3000

      • May 14
  • New
    rayauger02539
    Newcomer - Level 1
    2021-05-05

    e series 4.2 is there a knock down device to use 8 ohm speakers

    0 40
  • New
    Lergei
    Newcomer - Level 1
    2021-04-27

    Hi! I'm new here and don't know if i'm writing to right place but i bought this nice old SS300B power amp and i need service manual for it, can someone help me?

    Mikko 

    0 58
    • Lergei
      Nigel67 Hi Mikko, I am sorry, but I do not recognise this amplifier. If we do have schematics, then unfortunately we are not permitted to distribute them. There was a LAB 300. Is this what you have?
      • Apr 27
  • New
    jazzed
    Newcomer - Level 1
    2021-04-09

    Hello,

    How do I get in touch with Labgruppen in order to apply for a job or get information about available jobs.

    Jazzed

    0 44
    • jazzed
      DavidKnighton Hello jazzed,
      At the top of the page, please click ABOUT and then JOIN US from the drop down menu. Continue clicking through to find available job listings.
      • Apr 9
  • New
    Gheorghe17
    Newcomer - Level 1
    2021-04-05

    Hello,

    just got a used Lab Gruppen IP450, love this amp but the face plate ha some scratches.I need a new one and I was wondering if I can still find this kind of spare part ?

    Thank you in advance and hope for your positive reply.

    GD

    read more...
    0 31
    • Gheorghe17
      Nigel67 Hi Gheorghe, Please contact our spares team and they will be able to advise you availability and pricing. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Spares tab and submit a ticket. Many thanks
      • Apr 5
  • New
    johnaldrsn
    Newcomer - Level 1
    2021-04-03

    Hi there, first post here.

    I have a Lab Gruppen C20:8x and am getting no output from channel F. The CPL fault LED is constantly illuminated (orange) for that channel, also the VHF fault LED. This is irrespective of whether inputs/outputs are connected or not.

    Can anyone advise pls? Feel free to ask for further info. Thanks in adv,

    John

    read more...
    0 53
    • johnaldrsn
      DavidKnighton Hello johnaldrsn,
      This type of issue would warranty a service request ticket. Please click on SUPPORT at the top of the page and then scroll down to SERVICE REQUEST to stat your inquiry.
      • Apr 3
Go to page