Statistics

259,802 members
138,220 posts
  • New
    albucristian83
    Newcomer - Level 1
    2021-11-25

    Hello,

    Reading the product manual for the KT-2A leveling amplifier, found this written:

    "The controls on the 2A-KT consist of a Pre-Emphasis trimmer which adjusts the compressor / sidechain interaction. When set fully clockwise, the sidechain responds to the full frequency bandwidth of the incoming audio. As the trimmer is turned counterclockwise, the compressor responds less to the signal's high frequency transients."

    Shoudnt be the opposite for counterclockwise rotation? Meaning the compressor reacts more to high frequency acting like sort of a de-esser?

    I ask this because this is the functionality I know the older LA2A units have...

    Many thanks for reply and clarification.

    BR,
    Cristian

    read more...
    0 0
  • New
    Alibek
    Newcomer - Level 1
    2021-11-25

    Hello! Can I use KT-Dante64 CM1 card in DN9650 to connect Midas Pro console to AES67 devices? Does the card supports AES67? Do I need any additional gear? 

    Thanks!

    0 2
  • New
    husnain9
    Newcomer - Level 1
    2021-11-24

    Hello Team,

    This is Husnain from Pakistan and i have 100 audio processors Model: DMA-8500 each piece is for each classroom of different universities. Can anyone please help to suggest how can i use all input channels as i have 8 mics in each classroom. 

    Senerio is like i have 2 speakers which are connected with amplifier 2 seperate channel. Microphones connected with Digital Audio Processor work with first 2 channels but other channels are not working as it has to be configured. I would appreciate if anyone can share configuration mannual so all 100 devices can be configured accordingly. Thanks

    regards,

    Husnain 

    Email: [email protected]

    read more...
    0 8
  • New
    Davpis
    Newcomer - Level 1
    2021-11-23

    When will these be available again? I've been waiting over a year with Sweetwater it's backordered

     

    thanks

    0 3
  • New
    kountrykid
    Newcomer - Level 1
    2021-11-04

    Hello,

    As mentioned in the subject line, I'm trying to connect the brackets that came with my Klark Teknik DW20BR, so it can be mounted.  Though, the screws provided are too long after removing the black rubber feet that are originally mounted.  And, it doesn’t come with any shorter screws. Trying to figure out what I’m missing here? Thinking maybe I’m missing a step.

     

    Tony

    702-523-0126

    read more...
    0 3
    • kountrykid
      Nigel67 Hi kountrykid. It appears that you are doing everything correctly. The screws that you take out to remove the rubber feet should then screw straight back in. They screw back into an extruded aluminium case which should have threads made into it long enough for the screws to be tightened into. There is no pcb, etc in the way that they can be fouling on. The screws should be 15mm long. Can you confirm that they are this long? Either they are too long in the first place or the aluminium extrusion has not been threaded deep enough. I don't want you to force it, but can you try putting a little extra pressure on one of the screws to see if it tightens up any further. If not, then I would advise contacting the partner that you purchased the unit from and asking them for a replacement unit, making sure that they check the replacement unit so the screws do go all the way in when the rubber feet are removed. Have you checked all 8 screws? Many thanks
      • Nov 5
  • New
    sebastienP
    Newcomer - Level 1
    2021-11-04

    HI All

    I search an update firmware for DM 8500

    Someone can help me ?

     

    Thanks

    0 11
  • New
    nektarios303
    Newcomer - Level 1
    2021-10-19

    Hi,

    I own a pair of KT-2As (and 76-KTs) and wanted to ask two questions.

     

    1) Upon using stereo link and calibrating the two units with a 1khz test tone, using the Stereo Link trimmer at the back to get the same amount of gain reduction, I get different amounts of gain reduction between the two units when I move the Peak Reduction. The test tone is a mono signal sent to two outputs of my soundcard. No faders hhave been touched in my soundcard's mixer, the stereo output pair I am using on my soundcard, shows the same signal between the two outputs I am using for Left and Right that are the inputs to the KT-2As.

    So I am using them unlinked which is fine, but the bottom unit in the photo, needs to have the Peak Reduction pot much more CW than then top unit to show the same amount of gain reduction. How do I go about calibrating the unit so that it behaves like the top one?

     

    2) My units are running hot. I can put my hand on them, but they are very hot.

     

    Do other KT-2A owners experience these two behaviiours I am?

     

    Cheers!

    read more...
    0 16
  • New
    mblackuk
    Newcomer - Level 1
    2021-09-29

    Hi guys,

     

    My DN6000 has suddenly gone darker on the left side and a message saying "low battery" appeared. 

     

    I changed the battery (2430) and there is no low battery message any more but the screen is still dark on one side.

     

    I'm attaching a pic, can anyone shed a light as to what's happening? (excuse the pun) Thank you.

    read more...
    1 16
    • mblackuk
      WilliamR Hello, William from musictribe here. Please click on the support link above and create a support ticket and an agent will contact you ASAP to help you out.
      • Sep 29
  • New
    Joinville
    Newcomer - Level 2
    2021-09-01

    Good day,

    Any idea on how to send audio of DM8000 USB to A computer (50 mtrs)?

    0 21
  • New
    KlausMock
    Contributor - Level 2
    2021-08-19

    The Behringer QX mixers are equipped with a multi fx processor made by Klark Teknik.

    I would love to see a standalone device using this processor. Maybe a small one similar to the TC M100 or even in a 19" housing with, lets say,  two or four of that processors and the possibility to tweak more parameters for each effect, a tap tempo button, and so on. Something may be similar to the MX400 made by Lexicon but with all that phenomenal suberb effects of the Klark Teknik processors.

     I would buy both,the small one and the larger one,even if I own a M32, a X32, a WING (among others) and some vintage effects made by some well known manufacturers. 
    the components are already available,so put it in a box and ship it.

    kind Regards

      Klaus

    read more...
    1 46
    • KlausMock
      Dale_M Many thanks for your suggestion, we cannot promise it will be implemented but it will be given to the Design team for consideration.
      • Aug 19
Go to page