Statistics

305,338 members
189,620 posts
  • Mayank
    Contributor - Level 1
    2020-02-04

    Hello. Which material would be the best to put inside the ports of the Tannoy XY8F floor standers. 

    0 79
  • jppinbdx
    Contributor - Level 1
    2020-02-03

    Hi !

    I'd want to control my XR18 with both X-Touch and X-Touch Extender connected together on the router (with RJ45 cable) or connected themselves by USB. Is it possible ? Of course, without using a computer !!! I'd just like to use 17 faders in place of 9 !

    Thanks a lot for your ideas ... !

    And sorry for my poor english !

    Best regards,

    read more...
    0 138
    • jppinbdx
      KenMitchell

      HI @jppinbdx , 


       


      Welcome to the community.  Unfortunately, it is currently not possible to use the XT Extender to control an XAir mixer.  A firmware update to add XCTL protocol support would be needed. I "heard" it was in the plans, but have never heard an ETA. 


       


      Ken

      • February 3, 2020
      • Connect both X-Touch and X-Touch Extender to control X-Air XR18
        djtonic Hi KenMitchell, we are in 2022 and still no plans for it???
        • Jun 5
  • itexpertak
    Contributor - Level 1
    2020-01-17
    0 150
    • itexpertak
      KenMitchell

      Hi AJ ( @itexpertak ), 


       


      Welcome to the community.  That is kind of a loaded question since many audiophile's don't believe in EQ at all. They "fix" the room instead.  That being said, I personally use a Behringer Ultracurve Pro DEQ2496 that was set based on measurements from Room EQ Wizard (REW).  I can't say I'm an audiophile, far from it, but my system sounds good to me. 


       


      Hope this helps,


      Ken

      • January 17, 2020
  • agaurav009
    Contributor - Level 1
    2019-12-05

    I have made a basic setup using tv audio-aux out for music-source and microphones for vocals. I found music was noisy. So, I did lot of debug and the summary is as below:

    I started using only 1 channel out of 5-10, say M, keeping all other chanels mute i.e. all channels from 1-12 are mute except M. Even then I get quite noisy output on my soundbar. Source of music is youtube karaoke track from TV audio aux-output (of course TV audio is muted). Only weak point in connection I can't debug is the 3.5mm-male to 6mm-male cable or 3.5mm-female to 6mm-male converter. I have checked tv audio out using RCA cables to my soundbar and the music is perfectly alright. So, source is perfectly fine. Assuming the cables are alright (as chances of cable and adapter both being bad are low), its the mixer XR12. I think its my settings (.scn) as microphones sound alright but when music is entered through same mic-channel, noise is there. Any suggestion?

    read more...
    0 235
    • agaurav009
      RexBeckett

      @agaurav009 


      Hello Anand, welcome to the community.


       


      What type of connector is the TV output? If it is a stereo 3.5mm socket, you would need to use a cable like this to separate the two channels and connect the 6.35mm mono plugs to two adjacent channels - e.g. 5 & 6.


       


      If the TV output is RCA sockets, use a cable like this and also connect to two mixer channels.


       


      In both cases you should stereo-link the two channels in your XR12 setup using XAir-Edit.

      • December 5, 2019
  • Hubert
    Contributor - Level 1
    2019-12-04

    My compression driver tweeter on my right Westminster just stopped working out of the blue, just like that, at normal listening level. The Benchmark AHB2 was driving them. I am in panic and extremely anxious!! Please help

    0 142
  • jasbirnandra
    Contributor - Level 1
    2019-11-26

    I am interested to buy speakers from tannoy as there are no dealers here want to contact them and do not have any contact details can someone share the same, please.

     

    regards

    jasbirnandra

    0 495
  • IsaacFanz
    Contributor - Level 1
    2019-11-16

    Has anyone cascading fbq 100

    0 140
  • bakinj
    Contributor - Level 2
    2019-11-02

    Can someone, maybe Behringer, post clear, step by step instructions on how to run two bridged channels, as oppossed to 4 non bridged, on the NU4-6000?  Detailed, straight forward instructions that explain EVERYTHING that needs to be done to bridge A+C and B+D channels?

    Thank you

    read more...
    0 156
  • Thomasb12321
    Contributor - Level 1
    2019-10-18

    Hi, 

    I am very novice with audio but usually once I can play with things I'm very good at learning. I inherited a DEQ2496 and some other components. But there is no way for me to tell in what order I should hook them up in. For example, the amplifier, receiver, etc. If you could send me what order to hook things up, I'd very much appreciate it. Thanks. 

    Thomas

    read more...
    0 238
  • DaleM
    Contributor - Level 1
    2019-10-03

    Just purchased  a Behringer EP2000.  I would like to power two(2) 10" subwoofer externally from the sub pre out: what needed between the home reciever and the EP2000 to match the impedence?

    0 211
Go to page