• DLinke
    Newcomer - Level 1
    2020-09-04

    I have been looking at Yeti and other solar power generators to operate ip3000 outdoors for several hours.  Please, please give recommendations or at tge very least amps/wattage needed for at least a few hours of power for my ip3000.  Seems like u saw a Yeti with a briefcase unfolding solar panel.  I want to say it was a 1,000 or 1250 Yeti.   Cost I think was about $1,000 to $1500.   Would this power ip3000 for at least a few hours?   Please advise.    Thank you!

    read more...
    0 35
    • DLinke
      PedroRodrigues Hi DLinke thank you for your contact, the issue when using any kind of generators is the voltage fluctuations that happen and that might damage the IP3000 PSU. Never the less if you wish to select one solar power generators I would select the 1250 Yeti.
      The PSU for the IP3000 is the following
      • September 9, 2020
  • MrHavelTec
    Newcomer - Level 1
    2020-08-27

    Hello, I want to make my IQ10 airworthy. Now I have seen that there is the IQ10-WB wall bracket. Can I use this with an Adam Hall Super Clamp to hang the speakers on trusses?

    Thanks in advance for an answer!

    read more...
    0 49
    • MrHavelTec
      DavidKnighton Hello MrHavelTec. I can't give you a solid YES or NO in this case, because I've not personally had any experience with this exact clamp before. I will say that the wall bracket 'should' be compatible with any truss mounting hardware, such as a standard cheeseborough truss clamp. You just need to ensure the mounting bolt for the clamp fits properly into the wall bracket mounting hole. Alternatively you could use eye bolts and GAC to suspend from truss.
      • August 27, 2020
  • LeeE_Wolloff
    Contributor - Level 1
    2020-08-17

    I recently took delivery of 2 TFX122M-AN monitors.  One of them can be controlled with the PC Edit 1.3 software and is automatically detected.  The other one is seen by the Laptop, but won't connect to the PC Edit software.  Any suggestions?

    read more...
    1 50
    • LeeE_Wolloff
      PedroRodrigues Hi Lee, have you updated your unit with the latest Frimware 2.0? please follow the link below to access it https://www.turbosound.com/turbosound/search-results.html?queryStr=%20TFX
      • August 17, 2020
    • LeeE_Wolloff
      LeeE_Wolloff They both have 2.0 firmware installed. I even tried to re-install 2.0 in the malfunctioning one. No USB communication.
      • August 17, 2020
    • LeeE_Wolloff
      PedroRodrigues Hi Lee in this case please submit an assistance request by follow this link so we can assist you in more depth. https://community.musictribe.com/pages/create-new-ticket
      • August 17, 2020
    • LeeE_Wolloff
      LeeE_Wolloff I already did. The case number is CAS-130126-C4B4D8.
      • August 17, 2020
      • TFX122M-AN USB won't recognize PC Edit 1.3
        PedroRodrigues Hi Lee, I'm located in the UK one of my colleagues in the USA office will pick this up for a more local assistance. Thank you
        • August 17, 2020
    • LeeE_Wolloff
      LeeE_Wolloff Thanks Pedro.
      • August 17, 2020
  • DesmondLee
    Contributor - Level 1
    2020-08-13

    Where on earth I can download GLL files for Manchester? Anyone?

    0 40
    • DesmondLee
      john0121 Hi Desmond, I've uploaded them here for you:

      https://we.tl/t-arkEqfFeQv

      I'll talk to the web team to make sure they're added to the product pages too.
      • August 13, 2020
    • DesmondLee
      DesmondLee Hi John, thank you for the files. Appreciated. Is this for Ease Focus 2 or 3?
      • August 13, 2020
      • Manchester MV212
        john0121 focus 3
        • 1
        • ·
        • August 13, 2020
    • DesmondLee
      DesmondLee Is OK, already import to Ease Focus 3. Thank you again John.
      • August 13, 2020
  • HornSpacer
    Newcomer - Level 1
    2020-08-10

    Where can i relocate the Top columns for the turbosound ip 3000 for purchase  thanks

     

     

     

    tvดูบอลสด

    0 48
    • HornSpacer
      AlexLane Hi there, you cannot purchase just the top columns for the iP3000 without the base. Unless it's part of a service request where they need replacing.

      If the columns are broken and you need new ones, contact our parts or service team and provide details please.

      Use the SUPPORT button at the top of the page, create a care ticket and select Parts or Service.

      I am interested to know more about this request, why do you need just the columns?
      • August 10, 2020
  • Apgilbert2
    Newcomer - Level 1
    2020-07-31

    Hey,

    Does anyone know if you can turn the reverb on the IP3000 manually instead of using the iPhone app? I went through the menu on the sub and didn't see any options to turn effects on. Maybe I'm overlooking something ?

    Thanks

    Andrew

    read more...
    0 53
    • Apgilbert2
      AlexLane I am sure this is possible, but don't have a unit to find the exact button sequence right now. Let me see if I can find out for you!
      • July 31, 2020
    • Apgilbert2
      AlexLane I feel like this is somewhere on the Process -> Input menu...
      • July 31, 2020
    • Apgilbert2
      Apgilbert2 Thanks, Alexander....I did go through the menu but didn't see. I read the instructions and it says that you can do it manually or with the app...I will check the speaker out tonight - maybe I overlooked it.
      • July 31, 2020
    • Apgilbert2
      Apgilbert2 If anyone else knows how to turn the effects on, feel free let me know what I should be looking for. Any help is appreciated!
      • July 31, 2020
  • JonSelin
    Newcomer - Level 2
    2020-07-29

    One great feature of the iQ series is the Ultranet input.  However, if I run my iQ8 speakers via Ultranet and then want to send signal to my subwoofers - they do not seem to have an analog output for that. Given all of the DSP & connection options built in - I'd like to see this option in a Firmware update.  It's handy to be able to run a long distance with CAT5e cables alone - rather than needing to also run XLRs just for subs. (I'm aware that I can buy iQ15B or iQ18B subs and resolve it, but that's not in the budget.) 

    read more...
    0 50
    • JonSelin
      Paul_Vannatto This has been asked for a few times before. The answer has always been that it is not possible with the current DSP.
      • July 29, 2020
  • CarlJames
    Contributor - Level 2
    2020-07-26

    We inherited the use of some ip82 and we have also purchased some in order to

    balance the system and keep the systems intact. Used as std. upper-mid unit.

    The overall impression is a good compromise of enclosure, woofer, crossover and horn 

    dispersion, but not the tweeter which is a disappointment when compared to the rest

    of the system. We therefore have to use DSP correction files in our loudspeaker management

    adapted to various venues in order to correct for this. Otherwise, it measures reasonable,

    but sound harsh, no distinctive upper end etc. When will this unit be upgraded?

     

    read more...
    0 53
    • CarlJames
      AlexLane Hi Carl. I will forward to the relevant people. I can't give an estimate as to when updates may come but any feedback is welcome and listened to! :)
      • July 27, 2020
  • YukonPA
    Newcomer - Level 1
    2020-07-17
    Hello all... I own 2 x ip2000 and 1 ip300. I am looking for specific details of the DSP settings that are provided. What exactly is happening between the various options? (IE: Wall position versus Floor... Live Music versus Speech) What electronic changes are taking place? Does anyone have access to any graphs or written information? best!
    read more...
    0 73
  • Turbosound
    Triber Moderator
    2020-07-17
    We’re bringing new features to the Turbosound website to make it an even better experience! Visit https://www.turbosound.com/ today! #Turbosound #NewWebsiteFeatures
    0 57
Go to page