• scredly
    Contributor - Level 2

    Is there a button/power sequence to reset an IP2000?   Out of nowhere, the input sensitivity of one of my units is out of whack.   One unit volume is at 4.5 and the other is now at 26 to match it.     

    0 190
  • BigFire
    Contributor - Level 1

    I recently purchased a brand new full TLX84 rig and for the life of me cannot find crossover points at all for the HF and LF in this box. Can someone give me the HF and LF ranges? I can only find the range for the entire box.

    Also, when I was researching the Turbosound website said I would be provided with EASE files with these. I got nothing and can't find anywhere to download these. Help! I just invested a lot of money and would like to have these basic things. Thanks!

    0 211
    • BigFire

      Turbosound doesn't release DSP settings for TLX array's series, you must use dedicated amps, Lab gruppen PLM+ with Lake DSP on board. Eq settings, limiters, crossover and eq overlay are in the DSP presets downloadable from the product page.



      • October 16, 2019
  • gm12338
    Contributor - Level 1

    I sent back a Samson VX8.1 line array pa unit that was not working properly and decided instead to buy a Turbosound IP1000 which I rec'd 10/12/2019.  I only ran the IP1000 a few hours to practice on my Roland RD-2000. The rear metal plate where inputs plug in, gets almost too hot to touch.  Should I be concerned about internal heat build up as I don't see a visible cooling fan nor any air vent ports.  On the Samson VX8.1 I returned, plus many other models I've researched, do have a visible cooling fan and or air venting with some having possible non-visible internal fans. On this blog somewhere, I read someone was asking IF there was an effective way to retrofit a cooling fan solution for their speaker.  I do "know" that excessive heat does in fact break down electronics over time.  IS there any internal fan or any air porting/venting in any of the Turbosound Inspire IP1000 thru IP3000 models? I like the sound I'm hearing, I'm also thinking about pa system longevity too.






















    0 135
  • Djchillb
    Contributor - Level 1


    I will be attending the bpm trade show this weekend in Birmingham and o note that you will also be attending, I did enquire last year about the ip300 but you hadn't brought 1 with you

    if poss can I ask that you take 1 this year so I can have a look / listen as very interested in a pair

     thanks Ryan

    0 122
  • dhsherbert
    Contributor - Level 1


    I just purchased a Turbosound iP300 and had a question that is not addressed in the Quick Start Guide. I'll be using this speaker with my Laptop, Audio Modeling SWAM Wind Instrument software, EWI5000 and Focusrite Scarlett 2i2 Audio Interfacel. I need to use both Left & Right output signals from the Focusrite. Is it OK to use both Inputs of the iP300 for this?

    Thank you,


    0 185
    • dhsherbert

      Hi Doug ( @dhsherbert ), 


      Sorry no one replied to you earlier.  I just stumbled upon this when I was looking at your reverb question.  Yes, there's no issue with connecting to both inputs on the IP300 at the same time, whether it be from the same interface of different interfaces.


      Hope this helps, 



      • August 13, 2019
  • ArmandVermeulen
    Contributor - Level 2



    When the limiter is off, is there still a master limiter activated as to not push the system beyond it's capabilities?

    0 234
  • guitarman_nebr
    Contributor - Level 1

    Hey all,

    I have been using the IP2000's for a few months now.   They sound great....until I have to push them for a bit more volume.  I have a small band with pre recorded tracks for Bass and Drums...we sing and play guitar over these tracks.

    I seems there is a general agreement to set everything on the speakers DSP to "0" to use these as a PA speaker with a mixer.   However, it seems there is not a clear explaination as to how much input to use to optimize the output of the speaker.  

    The ouput runs hot and pegs out very quickly...to the point the system will cut out or clip.  I think Turbosound should do a video addressing input and output settings.  On the DSP display it will show the input at two bars and the output quickly goes off the scale.   It is hard to balance these two settings.  

    Does anyone have their own experiences to share?

    0 297
  • Dae_dalus82
    Contributor - Level 1

    I own 2 15 inch siena tsp152-ans.  I was going to buy a pair of 12 in loudspeakers but before i do i was wondering the differences between the siena, nuQ, and athens product lines.  The athens have different dispersion options but other than that i am unsure what their main selling points are.  If i go by frequency response and max spl then the sienas are the best bet.  The other two lines are more expensive and i wonder why that is?  Thanks for any help anyone can provide.

    0 270
    • Dae_dalus82

      @Dae_dalus82 I cant speak to all the exact differences but when I looked (at turbosound in general) a while back, some models that had the ultranet port, did not include an ethercon port with it. I know the enclosre on some models differed in materials used and would suspect the speakers and perhaps the on board amps are different in some key ways.

      • June 16, 2019
  • JulienRutyna
    Contributor - Level 1


    Je possède depuis 1 an 2 ip3000, j'ai deja eu 2 retour de garantie car une colonne s'est arreté d'un coup en pleine soirée. L'ecran reste allumé, les fonctions sont accessible mais aucun son ne sort.
    Aujourd'hui j'ai encore un probleme avec des coupures de son de 2 secondes toutes les 3 minutes sur une colonne.
    Je ne comprend pas cette enorme manque de fiabilité pour une marque comme Turbosound surtout que je fais attention a mes volumes d'entrée , j'ai lu sur les forums que c'est un soucis recurrent sur ce modele. Que puis je faire pour ne plus avoir de soucis car j'aime beaucoup ce modele qd il fonctionne.
    Merci beaucoup

    0 135
  • robykock
    Contributor - Level 2

    Hi I am helping a customer but not sure the proper mounts to use for the IP300 to hang them or suspend them from wall.  What is best practice for doing this?


    [email protected]

    0 134
Go to page