Statistics

250,516 members
127,682 posts
  • New
    jdinsdale
    Newcomer - Level 1
    2021-09-24

    Hi,

    Id like to get a copy of a schematic for F1220D powered monitor.

     

    Thanks Jeff

    619-787-4381

    0 4
  • New
    JavierBode
    Newcomer - Level 1
    2021-09-22

    I have 2 pcs of NU6000 BEHRINGER AMP needing to be replaced the AMP BOARD.  Please provide information about where to buy 2 pcs of AMP BOARD and the price. I need orientation toward solving this issue. THANK YOU!

    0 5
    • JavierBode
      Nigel67 Hi JavierBode. Please contact our spares department and they will be able to help you further. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Spare Parts tab and submit a ticket. A colleague will then get back to you with pricing and availability. Many thanks
      • Wed at 10:28 PM
  • New
    DEFF123
    Newcomer - Level 1
    2021-09-22

    The lights flicker on and off when I turn it on and when I turn it off.  What do you suggest?

    0 3
    • DEFF123
      DEFF123 I'm awaiting your answer.
      • Wed at 12:34 PM
    • DEFF123
      Nigel67 Hi Deff123. Unfortunately the device appears to be faulty. If you have tried another mains cable and mains socket and the LEDs are still flickering and you get no audio at all, then it needs to be serviced. You mention that the unit is new. If it is under 30 days old, then please go back to the shop that you purchased the unit from and ask for a DOA replacement. If it is over 30 days old, please send us a Technical Support ticket as mentioned by my colleague below and we will help you further. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Technical Support tab and submit a ticket.
      • Wed at 10:24 PM
  • New
    DEFF123
    Newcomer - Level 1
    2021-09-22

    I have a new PPA550BT the power  box lights flicker on and off when I turn it on.  The also flicker when I turn it off.  What do I do?

    I have no  sound on my PA

    0 2
    • DEFF123
      DEFF123 What do I do?
      • Wed at 12:30 PM
    • DEFF123
      KyleJohnson Hello, Kyle here with Music Tribe. Please contact our tech support directly by clicking on Support and then Technical Support.
      • Wed at 1:38 PM
    • DEFF123
      DEFF123

      • Wed at 8:35 PM
  • New
    DEFF123
    Newcomer - Level 1
    2021-09-22

    Please answer my 2 amplifier repeated question

    0 4
  • New
    Vin1
    Newcomer - Level 1
    2021-09-14

    I want to register my pa BEHRINGER C200, I bought it last month, I would like to register the product to benefit 3 years warranty, can you tell me what is further step to do to benefit extended 3 years warranty. My cell phone to contact me is 514-290-0772. My name is Vinh.

    Thanks!

    read more...
    0 6
    • Vin1
      PedroRodrigues Hi Vin1, please consider that you must submit an assistance request directly with our Tech Support Team by following the link below so we can assist you on the register process for your unit and perform the necessary verification to access if you qualify for the extended warranty. Please provide the serial number for your unit located on the unit and also attach the original invoice for this purchase Thank you
      • Sep 14
  • New
    BFAN111
    Newcomer - Level 1
    2021-09-13

    I added another amp and wanted to change my EP2500 to bridge mode operation from stereo.

    It seems like it will not allow me to run it in Bridge mode without enabling the Low frequency filter?

    Is this correct?  I cannot use an EP2500 in bridge mode to power a subwoofer without a low frequency filter?

    read more...
    0 1
    • BFAN111
      DavidKnighton Hello BFAN111,
      No, that is not correct operation of bridge mode. According to the manual, you need only push switch 6 & 7 to the ON position to enable bridge mode. Also note that parallel mode must NOT be active, so switches 4 & 5 must be in the OFF position. The remaining switches/controls for INPUT 1 are optional. The manual does state that the the INPUT 1 options are used specifically for bridge mode operation, meaning INPUT 2 controls are N/A. This statement does not mean that the controls need to be engaged for bridge mode.
      • Sep 13
    • BFAN111
      DavidKnighton
      • Sep 13
  • New
    HawaiianKidd75
    Newcomer - Level 1
    2021-09-09

    I have had the NX3000 for about 3 years hadn't had an issue at all.  Practiced as normal and the amp started blowing out bright white smoke.  It isn't dust related as it is in a Flight Case.  Still works ,however, I recently purchased the NX4-6000 from Sweetwater Mid July.  Second time being used was yesterday during band rehearsal and it duplicated the exact issue I experienced with the NX3000 and every channel went into Protect Mode.  Fans blew with much more force than normal operating conditions and all I had was 2 Peavy 12" Mains and a Peavey 500w Wedge.  Not nearly enough load to cause this.  Is this a defect or has anyone else ever experienced this issue. 

    read more...
    0 6
    • HawaiianKidd75
      john0121 Hi, unfortunately this sounds like a hardware fault in with the amp, please fill out the service request form via the support button at the top of the page and our team will arrange a repair with you.
      • Sep 10
  • New
    rsparkle22
    Newcomer - Level 1
    2021-09-03

    Is it safe to use pmp 4000 powered amp without speakers connected. I would like to use headphones and do home recording on the pc with tracks adding vocals. Thanks

    0 12
    • rsparkle22
      WilliamR Hello, Yes, solid-state power amps are safe to use without a speaker load. Only tube-driven amplifiers should not be run without a speaker load.
      • Sep 3
    • rsparkle22
      rsparkle22 Thank you.
      • Sep 3
  • New
    jp182
    Newcomer - Level 1
    2021-08-30

    I just bought a second hand AMP800 and I've plugged 3.5 to 1/4 cable into the input L & R into the amp with a pair of headphones plugged into the headphone jacks on the front.  

     

    Not only do I not get any sound, I also don't see any of the LEDs on the front moving which is making me think the AMP itself is not working.  I've tried multiple input sources in both input A and input B; same result. 

     

    Any other suggestions before I email the buyer to get a refund on a defective unit?

    read more...
    0 10
    • jp182
      ChrisEdwards1 Hi jp182, Are you aware if the unit was supplied with its original power supply or a third-party power supply? If a third-party power supply, I would recommend double-checking all specifications to ensure they match correctly including the polarity.
      • Aug 29
Go to page