Statistics

294,758 members
177,887 posts

Sort

Sort

Discover

  • New
    Pri2259
    Newcomer - Level 1
    2022-08-15
    Placa Main board | Digital Stagebox Mixers

    Olá a todos! Gostaria de uma ajuda pois estou precisando da placa Main Board Behringer X18 porque estou com esse Mixer sem solução aguardando somente essa placa. Teria alguma loja específica para que eu possa comprar?

    1 18
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    Manno83
    Newcomer - Level 1
    2022-08-13
    Prob with my s32 digital snake | Digital Stagebox Mixers

    How to repair 

    0 2
    0
    Mark As Solved 0 Reopen Discussion 0
    • 1 Replies
      Oldest
    • Manno83
      Nigel67 Hi Manno83. What is the problem with the S32 to begin with and I can then offer some advice. Many thanks
      • Aug 14
  • New
    GizmoG_Álvarez
    Contributor - Level 2
    2022-07-24
    Monitoring XR18/ X32 while using tablet/phone | Digital Stagebox Mixers

    How do you monitor with headphones when using a tablet or phone to control an XR18, X32 when in the need of soloing a channel? 

    As it only transfers commands and not audio you have to plug your cans in the mixer or use wireless beltpacks... 

    So I would like to know how do you approach this.

    Thanks in advance to all comments and suggestions.

     

     

    read more...
    0 11
    0
    Mark As Solved 0 Reopen Discussion 0
    • 4 Replies
      Oldest
    • GizmoG_Álvarez
      Nigel67 Hi GizmoG_Alvarez. You have answered your own question there. If the XR18/X32 is not within a short distance where you can use wired headphones, then your only option would be to go wireless.
      • Jul 24
    • GizmoG_Álvarez
      GizmoG_Álvarez I meant how do people approach this ... They go on RF, use more inexpensive devices...
      • Jul 25
    • GizmoG_Álvarez
      Paul_Vannatto I use to use headphones and solo channels when I used analog consoles. But when I switched over to the X32 Rack, I forced myself to learn to rely on my ears, the meters and the RTA. Same with the X-Air/M-Air consoles.
      • Jul 25
      • Monitoring XR18/ X32 while using tablet/phone
        GizmoG_Álvarez Finding spontaneous crackle, noise... or EQing is a task one should do soloing.
        One can rely on visual information when finding feedback or broad issues, but eqing a voice or similar tasks using visual information is not the right way. That's the way one uses his ears, not looking at what a RTA says.
        • Jul 25
    • GizmoG_Álvarez
      Paul_Vannatto You asked "how do people approach this" and I gave my approach - only to be knocked down.

      As I mentioned, I use to use headphones - they were either on my ears or around my neck. But when I switched to the X32 Rack (Oct 2014), I was forced to adapt, since I fell in love with the freedom of not being tied to a snake. I disagree that to find crackle, noise as well as EQing vocals, drums, etc. requires soloing. Actually it is much better to EQ to the equipment (speakers, etc) and venue ambiance than to cans (headphones).

      I do sound for 60+ events per year (except the pandemic years) using X32 Rack, MR18 or Wing (depending on the event/band/venue) and have learned to rely on this method with great success. It is a learning curve and takes a lot of effort. But it is well worth it in the end.
      • Jul 25
  • New
    mhbidadi94
    Newcomer - Level 1
    2022-07-25
    unstable Midas MR18 | Digital Stagebox Mixers

    Hello.

    I bought this MR18 from December 2021. It's unstable.

    It's mean at switch on gain is +27db , sound is good then switch off and again at switch on gain is +27db , sound is low !!
    Also FX faders one time -15db are good. Next time switch on FX are not good at -15db but FX at 0db are good !!

    Sometimes I have no signal at all.
    Sometimes the signal is very weak and cannot be heard at the output.

    Sometimes the volume gain is high, sometimes the volume gain is low, no matter how much I increase it, it is still useless
    I also did a factory reset, but it was useless
    There is no difference between any of the inputs, microphone, aux, there is no difference
    As I said, sometimes there is no signal at all.

    The supply of parts is not my problem, it is your problem and you should fix the problem. Otherwise, I will file a legal complaint against you.
    My MR18 has 3 years warranty, so I will come to Dubai next week. Please take my device back and give me a new one.

    read more...
    0 14
    0
    Mark As Solved 0 Reopen Discussion 0
    • 1 Replies
      Oldest
    • mhbidadi94
      Nigel67 Hi mhbidadi94. You will need to contact the shop that you purchased the unit from and ask them to repair the unit under warranty. If you would like to talk to our Technical Team with regards to your issue, then please raise a Technical Support ticket. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Technical Support tab and submit a ticket. Many thanks
      • Jul 25
      • unstable Midas MR18
        mhbidadi94 Hi Nigel67
        I mentioned my MR18 problem to the prolab store and also email [email protected]
        But still none of them gave me any correct answer about which country and which store and to which person I should return the mixer.
        • Jul 25
      • unstable Midas MR18
        Nigel67 You need to contact the store that is on your invoice for when you purchased the unit. Contact them and ask them to repair the unit under warranty.
        • Jul 25
  • New
    rtoussaint
    Newcomer - Level 1
    2022-07-09
    Firmware Error | Digital Stagebox Mixers 
    Hello,
has anyone solved the problem of firmware update .. (unrecognized) on PC?
Impossible to update, even on an old PC


    read more...
    0 13
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    Fernaic
    Newcomer - Level 1
    2022-07-08
    S16 box is changing settings on its own | Digital Stagebox Mixers

    Sometimes I turn on the box and its in 'SN Mode'. Other times its in "Splitter" mode. Other times it is in the '1-8' mode its supposed to be in. If I hold 'Config' and scroll through, I have two '1-8' modes, the normal one and then a second one where the 'Splitter' light is illuminated. I did not see mention of that in the manual.

    Is any of this explainable? Do I have a bad box?

    read more...
    0 5
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    oliverantomg
    Newcomer - Level 1
    2022-07-05
    Consulta | Digital Stagebox Mixers

    Compre una mixer Behringer Flow 8 pero en casa no tengo internet en mi computadora. Como le hago para ponerla a funcionar?

     

    0 5
    0
    Mark As Solved 0 Reopen Discussion 0
    • 1 Replies
      Oldest
    • oliverantomg
      KyleJohnson Hello, Kyle here with Music Tribe. In order to control the Flow 8 you can use your mobile device (smartphone or tablet running Android or iOS). The FLOW 8 apps are available on both downloads stores. You will, however, need to update the FLOW 8 to be compatible with the latest app versions, the update requires a Mac or PC. You must download the updater software from the FLOW 8 webpage and connect the FLOW 8 via USB to your computer to process the update. I'd recommend trying to find a place where you can connect your computer to the internet and perform the update.
      • Jul 5
  • New
    BCDurham
    Newcomer - Level 1
    2022-06-12
    Is it possible to copy/paste aux outs in Behringer Xair 18? | Digital Stagebox Mixers

    Hello,

    Is there a way to copy/paste or save/load the settings of one Aux out to another?

    For example, my IEMs come from Aux out #1 and I want to move my IEM settings to Aux out #5, is there a way for me to copy the settings from Aux out #1 and paste them to Aux out #5?

    I have tried copying/pasting and saving it as a channel preset and then loading that preset to Aux out #5, but neither method worked.

    Thanks!

    Brian

    read more...
    0 17
    0
    Mark As Solved 0 Reopen Discussion 0
    • 2 Replies
      Oldest
    • BCDurham
      NicJonesMT Hi BCDurham.

      If you could please click support at the top of the page and submit a technical support ticket along with your full scene, we can have a look at what is going on.
      • Jun 12
    • BCDurham
      CraigFowler Sort of, but probably not to the extent that you want. The channel>bus send levels are properties of the individual channels themselves; ch1>bus1 send level is a property of ch1, ch7>bus1 send level is a property of ch7 etc. When you copy and paste a bus all you'll get is the bus's own processing; it's own eq\compressor etc. You won't get the send levels of the channels feeding the bus, because those send levels are part of the channel, not the bus itself, and that's not what you've copied.

      If you want you could route bus1 to the aux5 socket.
      • Jun 12
  • New
    Patriot2020
    Newcomer - Level 1
    2022-06-03
    X32 Compact + SDA. Not getting any sound out of SD8 | Digital Stagebox Mixers

    I have an X32 Compact connected to an SD8.  I have recieved audio from the SD8, but I can not seem to be able to send.  I'm using it to connect the production truck to the house audio to send and recieve a few signals.

    0 16
    0
    Mark As Solved 0 Reopen Discussion 0
  • New
    Capera
    Newcomer - Level 2
    2022-05-22
    WING firmware version vs. stage box version compatibility | Digital Stagebox Mixers

    More and more I encounter problems with connectivity. My WING has latest firmware, but in the venues I visit, older stage boxes are at hand with unknown firmware versions. Owners don't allow me to update their stuff, what can I do?  I am desperately searching for a comprehensive compatibility matrix that tells me what desk version (X32, M32, WING)  is working with what stage box version (S16, DL32 etcetera). Please help. Actually, I want this info included with every update zipfile. I mean, having stuff is one thing, maintaining it becomes a critical issue now. I am pleased with the firmware update support pages, but having knowledge is becoming more and more important!

    read more...
    0 12
    0
    Mark As Solved 0 Reopen Discussion 0
    • 3 Replies
      Oldest
    • Capera
      Paul_Vannatto You should either insist that the owners keep their stageboxes up to day (firmware) or bring your own stagebox to the venue.
      • May 22
    • Capera
      elcholo5 i just buy 2 wings and 3 sd16 and i cant make it work together as 1 in foh and the another in monitor how can i make it work?
      • Jun 3
    • Capera
      Paul_Vannatto elcholo5, stop posting multiple times to other's threads that are not related to your question. Start your own thread (discussion) and we will try and help you.
      • Jun 4
Go to page