Statistics

285,084 members
166,987 posts
  • Adriano1972
    Contributor - Level 1
    2019-11-18

    Hi, I've been using an Xr-18 for a few years now and have never had problems with the XAir app, but these days ago I updated IOS to version 13.2.2 and to my surprise was that the app is no longer working as it should. Can anyone help me regarding this? What should I do ? The latest app update is over 2 years old, will anyone solve this?

    read more...
    0 162
  • ldodsworth
    Contributor - Level 1
    2020-02-04

    I'm a newbie to this site and to home audio. I have three questions regarding the FX2000.

    1. Am I too assume that this unit is just an effects processor or is it an interface as well?

    2. I wish to run a mic into it and out to powered speakers. Is this possible or do I have to run it through a mixer first?

    3. I'm also assuming that there aren't USB or SD capabilities to be connected to a computer for recording purposes and that the unit will have to go through a usb mixer.

    Maybe simple and straight forward questions but I'd appreciate any answers. Thanks y'all!

     

    read more...
    0 137
  • Djcnote79
    Contributor - Level 1
    2019-11-20

    I have two behringer nx 6000 they went into protection mode I hit the reset button but its still in protection what do I need to do

    0 132
  • markrazack
    Contributor - Level 1
    2020-03-20

    I'm interested in the Behringer NX3000 Power Amplifier. What is the RMS Continuous power output of this amplifier into 2, 4 & 8 Ohms? Is the amplifier 2 Ohm stable? What is the Peak/Maximum power output also at 2,4 & 8 Ohms? Do i need an equalizer for this amplifier? I am interested in the Behringer FBQ3102 Equalizer, Is this equalizer compatible with this amplifier, and is it a good EQ to match this amplifier with? Can i run this amplifier at 2 Ohms continuously? Will that cause any damage to the amplifier? Can the amplifier be run in mismatched loads/impedance, for instance if i want to run channel 1 at 2 Ohms and Channel 2 at 2.67 or 4 Ohms? I'm interested in the 220-240 Volts variant of this amplifier, Do I need a voltage regulator for the device, since AC Voltages tend to fluctuate world wide? Or is the amplifier designed to withstand voltage fluctuations without issues? At maximum volume, what would the power consumption of the amplifier be? If I buy the 220-240 Volts Variant of this amplifier, Can it work on the FBQ3102 Equalizer if it's 120 Volts? I can buy a step down transformer for the EQ so it can plug into 220-240 volts just as the amplifier, Would that be okay for the amplifier to be 220-240 Volts and the EQ to be 120 Volts? Will they work together or be any compatibility issues? Or can they damage each other in any way due to this configuration?

    I've read online that there was an issue with the Behringer iNuke Seriess, Especially the iNuke NU3000 where they go into protection mode, also I read that there were some Schottky Diodes issues in the iNuke Series amplifier, Were these issues addressed and corrected the the NX Series amplifier? The NX Series is the newer version replacing the iNuke, right? What is the input sensitivity of the NX3000 @ 2,4 & 8 Ohms? What's the difference between the red and amber light on the unit, one says limit and protect, isn't there a clip light? Can tell me how to match my gains between my equalizer, source unit and amplifier? Is there any documentation?

     

    read more...
    0 558
    • markrazack
      AlexLane

      Hi Mark,


      OK wow lots to get through here, let me take a deep breath aannnnnnnd...


      What is the RMS Continuous power output of this amplifier into 2, 4 & 8 Ohms?


      2 Ohm - 2 x 1500W
      4 Ohm - 2 x 900W
      8Ohm - 2 x 440W


      Bridge 4 Ohm - 3000W
      Bridge 8 Ohm - 1500W


      You need headroom though, its allways best to aim for a MINIMUM of 20%, so take your loudspeakers RMS power rating and ensure it is AT LEAST 20% lower than the above figures.


      Is the amplifier 2 Ohm stable?


      Yes in normal operation, No in bridge mode.


      What is the Peak/Maximum power output also at 2,4 & 8 Ohms?


      You can assume this to be double the RMS rating.


      Do i need an equalizer for this amplifier?


      I would reccomend some kind of loudspeaker processor yes, but it really depends on the application. What speakers are you planning on driving with the amplifier?


      I am interested in the Behringer FBQ3102 Equalizer, Is this equalizer compatible with this amplifier, and is it a good EQ to match this amplifier with?


      I think you are better off with a loudspeaker processor such as the DCX range, the FBQ would work as an overall system EQ.


      Can i run this amplifier at 2 Ohms continuously?


      YES! (But not in bridge mode)


      Will that cause any damage to the amplifier?


      NO! (Unless you run it at 2 Ohm in bridge mode or over load it by driving speakers with too high a power rating)


      Can the amplifier be run in mismatched loads/impedance, for instance if i want to run channel 1 at 2 Ohms and Channel 2 at 2.67 or 4 Ohms?


      Yes you can do this.


      I'm interested in the 220-240 Volts variant of this amplifier, Do I need a voltage regulator for the device, since AC Voltages tend to fluctuate world wide?


      No you shouldn't need a regulator, unless you are somwhere with truly unstable power! 


      Or is the amplifier designed to withstand voltage fluctuations without issues?


      As long as they are in the 220-240 volt range you will be fine. It's generally worth testing your power source before running a show!


      At maximum volume, what would the power consumption of the amplifier be?


      This is a very subjective question, you are better off looking at an average as music is inherrently not maximum power all the time. 1/8 rated power is pretty standard. 350W is a sensible figure.


      If I buy the 220-240 Volts Variant of this amplifier, Can it work on the FBQ3102 Equalizer if it's 120 Volts?


      If the power sent to each is from a seperate and appropriate source then yes, the FBQ will immediatly blow its fuse if given 220 volts and the amp will simply not turn on if its given 120 volts.The line level outputs will remain the same voltages so you can feed the 220 volt amp from the 120 volt EQ if thats what you want to do.


      I can buy a step down transformer for the EQ so it can plug into 220-240 volts just as the amplifier, Would that be okay for the amplifier to be 220-240 Volts and the EQ to be 120 Volts?


      See above answer, be careful please


      Will they work together or be any compatibility issues? Or can they damage each other in any way due to this configuration?


      Again, be careful! The power input will not affect the line level output or input voltage.


      I've read online that there was an issue with the Behringer iNuke Seriess, Especially the iNuke NU3000 where they go into protection mode, also I read that there were some Schottky Diodes issues in the iNuke Series amplifier, Were these issues addressed and corrected the the NX Series amplifier?


      I am confident that this is resolved.


      The NX Series is the newer version replacing the iNuke, right?


      Kind of yes, its a new range of amps.


      What is the input sensitivity of the NX3000 @ 2,4 & 8 Ohms?


      For rated power into 4 Ohms its 0.775 volts or 0dBu


      What's the difference between the red and amber light on the unit, one says limit and protect, isn't there a clip light?


      Amber = careful now your close to limit
      Red = Please turn me down! I am limiting and will go into protect mode shortly.
      Loss of audio = I am now in protect mode, you hurt me.


      Can tell me how to match my gains between my equalizer, source unit and amplifier? Is there any documentation?


      Research gain staging, generally you want to feed the amplifier with as "hot" an input signal as you can without clipping. This will ensure that when you come to turning the amplifier gain up your input signal is nice and far above the noise floor. Amplifying a low input signal means the noise floor is closer to the level of the input signal and you end up with a noisy output as you are gaining up the noise floor.

      Annnnnd breath out...

      Hope that helps

      • April 7, 2020
  • New
    emmaflorence1786
    Newcomer - Level 1
    2022-02-08

    does anyone know where i can get my speakers serviced in Canada.

    they are under warranty.

    i have opened a ticket 9 days ago and cannot get anyone to answer me.

    0 11
    • emmaflorence1786
      tylerbielan

      You can visit https://community.musictribe.com/pages/support and submit a care ticket. ultra pixel survive

      • Feb 10
  • apauletto
    Contributor - Level 1
    2020-03-22

    I am on my second broken Behringer amplifier in less than two years. I have tried contacting support for repair or replacement and have not heard back whatsoever. I have spent over $600 on these amps, have kept them in fantastic condition, and they both went out randomly. Any instruction as to how to move forward is greatly appreciated.

    read more...
    0 116
    • apauletto
      RexBeckett

      Hello @apauletto , welcome to the community.


       


      Did you raise a ticket through the Care portal? If you tell us the ticket number we can get someone to see why you didn't get any response.

      • March 22, 2020
  • New
    Bigalsy
    Newcomer - Level 1
    2021-11-15

    Tannoy TS 2.8 Subwoofer problem. 

    I have 2 of the above, 1 of which has bn repaired under warranty but now the 2nd 1 is doing the same. The red led is flashing quickly and won't change to green. Any ideas please

    0 9
    • Bigalsy
      Nigel67 Hi Bigalsy. The subwoofer is stuck in standby mode, probably caused by a fault on the power supply. Is it still under warranty? Even if it isn't, we can still repair it. Please submit a ticket to the Service Team and they can arrange a warranty / non warranty repair for you. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Service tab and submit a ticket. Many thanks
      • November 18, 2021
  • New
    Bluesy21
    Newcomer - Level 1
    2021-12-17

    HI,

    I just bought a MP76, I downloaded the update to my Voicelive play to be able to setup the MP76. My problem is that when I press the Upper button on the mic, setted on the Hit button of the VLP, no effects come in.   I did all the setup on the VLP, selected the functions etc. so that all the effects should comes when I press the mic. When I press the mic, The Hit button lights up but no effects comes in.  Discouraged, the mic is new and I cannot send it back to the store.  Anyone had the same type of problem? THanks

    read more...
    0 3
  • Analizaplazaro
    Contributor - Level 2
    2020-02-20

    Hi please help how can i connect my mixer to my TV and powered speaker?

    thank you

    0 277
    • Analizaplazaro
      RexBeckett

      @Analizaplazaro 


      Hello Analiza, welcome to the community.


       


      We should be able to help if you tell us the make/model of your mixer, TV and powered speaker.

      • February 20, 2020
    • Analizaplazaro
      Analizaplazaro

      @RexBeckett 


      thanks for your reply..


      tv - philips


      mixer - behringer 1202fx


      powered speaker - rockville bp10


       

      • February 20, 2020
    • Analizaplazaro
      RexBeckett


      @Analizaplazaro wrote:


      @RexBeckett 


      thanks for your reply..


      tv - philips


      mixer - behringer 1202fx


      powered speaker - rockville bp10


       





      @Analizaplazaro 


      You should be able to connect the 1202FX Main outputs to the BP10 channel 1 inputs using TRS/TRS cables like these. Without knowing the model of the TV, it is not possible to say how it could be connected to the mixer. Some TVs have two RCA output connectors for sound. If so, you could use a cable like this to connect to one of the 1202FX stereo inputs (5/6, 7/8, 9/10 or 11/12).

      • February 20, 2020
  • Happy_Mohab
    Contributor - Level 1
    2020-03-22

    Can I route the RCA outputs on the back of the UMC 204 HD to send to a Dazzle for video and audio recording live?

     

    0 112
    • Happy_Mohab
      AlexLane

      Hi and welcome to the community,


       


      I see no reason why this would not work, though I have no experience with Dazzle!

      • April 7, 2020
Go to page