Statistics

294,005 members
177,065 posts
  • New
    VettkA
    Newcomer - Level 1
    2021-08-06

    Where can I buy a gain potentiometer on the Behringer XENYX 502, otherwise it rustles when I rotate and I can't adjust the gain !!!

    1 42
    • VettkA
      WilliamR Sometimes it helps to spray it with contact cleaner, especially if you are getting a scratchy noise. I would try this first to see if it clears up this noise. If this doesn't work, you can click on the support link above and create a parts case.
      • August 6, 2021
    • VettkA
      VettkA

      Isn't it so difficult to order the potentiometer I need from the factory ?????

      • August 11, 2021
    • VettkA
      VettkA

      I thought that the Behringer company is good with high-quality equipment, but it turned out to be completely poor quality, since I can not buy an amplification potentiometer on the Behringer XENYX 502. Why can I not buy a potentiometer from production ?????

      • August 24, 2021
  • New
    JDLX
    Newcomer - Level 1
    2021-09-29

    Hi ! hI! I am an owner of the DAW Presonus Studio One 5.4 I would like to ask something about Behringer X touch one. Many users on the internet say that when you select a track from the x touch one , the track is not selected on the mixer of Studio One. Is this problem fixed with the latest firmware update(1.8) ( I have not bought x touch  one yet)

    read more...
    0 69
  • New
    Vivian99
    Newcomer - Level 1
    2021-10-19
    • Hi, I am very new to recording. Recently I got myself a behringer xenyx q802usb and when come to setup, I got a few issues.

     

    • Hissing sound during playback

    When I playback the record, there a hissing sound all over on the sound. I tried noise reduction in the app but still there's a hissing sound is too loud and it effects the sound I want.

    I lowered the microphone levels and it's seem worked a little but there's still a lots of others hissing sound like electricity and it's effected the sound I want. (No hissing sound heard when recording)

    Any suggestions how to fix it? (I have confirmed it is not surrounding noise)

    • Outputs

    When I play songs or YouTube through the mixer, I noticed that I could only hear the background songs. The vocal and human sound are extremely small or totally missing. I put up the gain, it works a little but at the same time the noise are also been turn up.(Checked the connecting cables, not the issue)

    read more...
    0 23
    • Vivian99
      Nigel67 Hi Vivian. These are not questions that we are going to be able to answer easily via this forum as a lot more information is going to be required on your set up, etc. Please can you submit a Technical Support ticket and we will be able to help you further. This can be done by clicking on the support tab at the top of the page. A new window will open. Scroll down and click on the Technical Support tab and submit a ticket. Many thanks
      • October 19, 2021
  • New
    jons1
    Newcomer - Level 1
    2021-12-31

    Is there a user manual available for the UMC204HD that has moe info the Quick Start Guide?

    0 16
  • New
    tonydunn
    Newcomer - Level 1
    2022-01-17

    When entering Patterns into a Track, I have noticed that the TD3 seems to almost randomly choose which Pattern and more importantly Pattern Section is to come after the most recently inserted Pattern, and I don't understand why.

    By way of example, say I want to enter 3 patterns, numbers 1, 2 and 3, all in Pattern Section A, in Pattern Group I. Set up for Track 1, start the sequencer running, select Pattern 1, Write/Next, then sometimes the TD3 stays on that Pattern ready for next insert into the Track, but other times it selects the next Pattern for me (by what I logic I do not know), and this is where I'm baffled, because it sometimes jumps to Pattern Section B and a Pattern of its own choosing.

    I can obviously change Pattern to the one I want (so in this example, Pattern 2 in Pattern Section A, Pattern Group I) but I would like to know why the change in Pattern Section happens, so if possible I can avoid it happening.

    Part of the reason for wanting to understand this is to prevent me not noticing the change in Pattern Section when inserting a Pattern into a Track, and inserting a pattern from Section B rather than Section A, and confusing myself when I play back the Track.

    I did just this and inadvertently inserted from B not A, and the inserted Pattern (from B) was empty. t was only when I noticed the LED light up to show me which Pattern Section the Pattern to be inserted was coming from, that I realised (1) what was happening and (2) why the Track was not playing back what I thought I had entered :)

    Of course, paying attention to what the TD3 is showing me is the next Pattern for insertion is the right thing to do, but I found it easy to make a mistake, and would like to avoid that, if possible.

    Anyone else see this happening, and if so, how did you fix it?

    Many thanks

    Tony

    read more...
    1 17
  • New
    ripebananas
    Newcomer - Level 1
    2022-02-02

    The Pi 400 is an extremely low cost arm computer integrated into a tiny keyboard design, running Raspberry Pi OS (based on Debian Linux).  https://www.raspberrypi.com/products/raspberry-pi-400/

     

    The Pi 400 comes without an audio interface, but 3 USB ports, so the UMC22 is an ideal option for recording and playback. In my case I had a lot of old recordings on minidisk, and as a project wanted to see if a Raspberry Pi could be used for mastering these old recordings.

     

    I am happy to say the UMC22 worked out of the box, and flawlessly with Audacity.

     

     

    read more...
    0 11
  • New
    Leehealy85
    Newcomer - Level 1
    2022-02-20

    I have set up the system but the receiver does nort recognise that the microphone I'd connected  

     

    Any assistance greatly appreciated 

     

    Kind regards 

    Lee

    0 16
    • Leehealy85
      NicJonesMT Hi Leehealy85.
      On the back of the receiver (By the XLR output) there is a small pinhole.
      With the Mic off, power up the Receiver while holding a pin in. Power up the Mic and keep it within 4 inches of the receiver. Wait a few moments and it should pair up.

      If this doesnt work then please click support at the top of the page and submit a technical support ticket.
      • Feb 20
  • New
    DanaT
    Newcomer - Level 1
    2022-04-14

    Good morning, if this question has been asked before, I apoligize for asking it again. This community has a welth of information but to be honest, it is one of the hardest forums I have found to find anything and I design communities for a living. So if someone can point me to any videos on how to naviget this community, that would be great. The X32 manuals say that that aux outputs are balance, yet the block diagrams show they are not. Any help would be great on either of my two issues. TYIA.

    read more...
    0 8
    • DanaT
      Paul_Vannatto Yes they are balanced TRS.
      • Apr 14
      • Are Aux Outs Balanced on X32 Mixers
        DanaT Then it would be safe to say that the block diagram in the manual is incorrect?
        • Apr 14
    • DanaT
      DanaT

      I have no idea why it posted my reply 3 times.

      • Apr 14
    • DanaT
      Paul_Vannatto Unfortunately this "new-fangled" forum interface only shows the left side of the image you attached. Looking at the block diagram of the X32 User Manual (page 65) the Aux Return (labeled correctly, since the Aux In/Out can be configured as insert pairs on the Routing, Aux Out screen) shows it correctly, where the tip and ring go to the preamp and summed, then to the A/D converter, similar to the XLR inputs. I can assure you that the Aux In jacks are balanced.
      • Apr 14
  • New
    avtechpro1
    Newcomer - Level 1
    2022-05-04

    Hi, I am new to MusicTribe. I recently signed on because our X32 Producer will not boot/ start up and I neeedd to contact tech support. I opened up support ticket and I did hear back with from tech support with some trouble shooting suggestions. When it was determined that the trouble shooting suggestions were not going to work. Tech support asked for information such as serial number, receipt etc. The X32 is out of warranty so I asked tech support to provide me with a list of authorized service centers so I could send the X32 off for repair and I never heard from tech support again. I send my request for service center list 3 times and they never got back with me. What is up with that? Just becuase a device goes out of warranty does not mean that support should just disregard my requests. I am authorized to either send this unit out for repair or buy a new mixer. I have lost confidence in Behringer and may choose to go with another companies mixer. Totally disappointing.

     Ed Whittle

    Audio Visual Production Specialist

    Yosemite National Park

    read more...
    0 36
    • avtechpro1
      Dale_M Sorry to hear this has been your experience, please can you advise your case number so I can chase this up for you?
      • May 5
    • avtechpro1
      avtechpro1

      Case Number CAS-598191-V9B6V3 .

      • May 5
    • avtechpro1
      avtechpro1

      Thank you

      • May 5
    • avtechpro1
      avtechpro1

      • May 10
  • New
    djtetei
    Newcomer - Level 1
    2022-08-05

    Currently Behringer power amplifiers power ratings are expressed using the term "max power" and Behringer officially states that "you can expect the RMS/continous power rating would be "around" half the declared max power rating".

    What does "around" half really means? It is "around half" at least or "around half" at most?

    Specifying "Max power" only for a power amplifier could mean that its continous long term power rating may be anywhere over "around half" or under "around half", which makes it difficult to design and calculate a sound system and to choose the proper power amplifier for the loudspeakers for which the continuous and peak power ratings are known.

    What methods or guidelines does Behringer use or follow to determine the power rating of its power amplifiers?

    Are amplifiers tested with sine wave test tones at different frequencies inside the supported bandwidth?

    Are amplifiers tested with pink noise (what crest factor) inside the supported bandwidth?

    Are amplifiers tested with both or all channels driven?

    What is the maximum THD allowed during the power rating procedure?

    What is the resolution of the digital signal processing units used on the power amplifiers with DSP?

    Thank kindly!

    read more...
    0 8
    • djtetei
      WilliamR Hello, Please click on the support link above and create a tech support case and an agent will get back to you ASAP.
      • Aug 5
Go to page