Statistics

233,969 members
109,567 posts
  • New
    gerard33
    Newcomer - Level 1
    2020-12-18

    Hello - I have just joined this group. I need a replacement tweeter for my Tannoy Mercury M2 speaker, please.

    Could anyone help me? Or even direct me to somewhere I might get one.

    Thank you in advance - Gérard

    0 62
    • gerard33
      RexBeckett Hello Gerard. I suggest that you open a Care ticket for this.

      At the top of this page, click Support then scroll down and select Parts. Make sure that you enter all required (*) data before clicking Submit. The Care team will respond by email.
      • December 18, 2020
      • Replacement Tannoy M2 / M3 tweeter required please
        gerard33 Thank you Rex - I have now just submitted. fingers crossed ☺
        • December 18, 2020
  • clive1101
    Newcomer - Level 1
    2020-10-02

    I have a tannoy definition subwoofer and the amplifier has gone for the third time, any recommendations for a replacement and are the speakers in phase ie both push at the same time or push pull so that one cone moves out of the cabinet while the other moves in on the same note.

    read more...
    0 62
    • clive1101
      ChrisEdwards1 Hi Clive, I hope you are well. I can see you have also submitted a case for this inquiry, I will be in touch with you shortly via the case to provide some additional information on this.
      • October 4, 2020
  • New
    NoamA
    Newcomer - Level 1
    2021-03-20

    Hi, I live in Irvine, CA. I would like to buy Revolution XT 8F-GW and take delivery before April 15, but I cannot find any reseller in the US which has it in stock.
    Can you help? Thanks,
    Noam  [email protected]

    0 29
    • NoamA
      Dale_M Hi Noam are you able to submit the above through on a Pre Sales Support ticket? I can then see if the team are able to advise you (as they are not on community)
      • Mar 21
  • New
    Jesionblue
    Newcomer - Level 1
    2021-04-22

    Hi there, one of my tannoys 8D studio monitors has blown tweeter and I'm looking for its replacement it has been weeks now, any idea where I can get one? Looking forward to hear from you, thanks

    0 35
    • Jesionblue
      Dale_M Hi there, please go to the Support tab above and create a Spares ticket, the team will get back to you and advise price and availability.
      • May 13
  • New
    Volta
    Newcomer - Level 1
    2021-04-06

    Hi,

    We are looking for recone kits for the Tannoy DC2546 speaker. There are four DC2546 speakers used as mid speakers in our Hill M4 PA system. All four of them have to be reconed. 

    0 32
    • Volta
      KyleJohnson Hello, Kyle with Music Tribe here. For parts ordering please click on Support at the top of the page and then submit a Spare Parts ticket.
      • Apr 6
  • EvoLunatic
    Contributor - Level 1
    2019-10-10

    Hi,

    I have an issue with one speaker. I barely get high frequencies. I need a manual inorder troubleshoot and disassemble the driver. Might be a loose wire.

    Who do I contact regarding this?

    0 146
  • New
    Teamfabix
    Newcomer - Level 1
    2020-12-18

    Hello, 

    I recently got a system IDP 10" and it works amazingly. 
    I am looking for the software ro my Mac to control the internal parameters. 
    Where I can find a copy and license? 
    best, 

    0 45
    • Teamfabix
      ChrisEdwards1 Hi Fabix, I have included a copy of the requested information in the below link. I hope this helps.

      https://we.tl/t-IGtRPd0EYz
      • December 22, 2020
      • Tannoy IDP 10 system - software and calibration
        Teamfabix Chris, Thank you very much for the files. I have to spend minute to remove the dust from one old PC with win XP )))
        I am going to get the Tannoy Vnet USB and RS232 Interface to connect the speakers as well. Thank you very much for your support! have a wonderful day! Merry Xmas to you and family.
        • 1
        • ·
        • December 23, 2020
    • Teamfabix
      Stan369 Hi just find out the oil leak back of speaker ? Is the normal?
      • May 24
  • New
    Timons
    Newcomer - Level 2
    2021-01-04

    I have the Tannoy Gold 8s as front-right and front-left, with the Gold 7 as a center channel, and an Infinity 10" sub. I'd like to stick with Tannoys for the rest of my setup: a) 2x rear surround and b) possibly speakers to bounce sound off the ceiling. I may also swap out the sub, but that is lower priority.

    The challenge for the rear surround is that I need powered in-wall, since it will be really inconvenient to wire from the receiver to the surround location. I will need to paint over the grill to minimize the visual impact. My receiver is an Arcam AVR390, and I expect to be sending the signal wirelessly via an SVS wireless transmitter and receiver.

    Any recommendations for the rear Tannoy speakers?

    Thanks!

    read more...
    0 39
  • Jonno
    Newcomer - Level 1
    2020-08-14

    Hi.

     

    I have recently picked up a pair of used reveal 8D monitors, but I can't get any sound out of them whatsoever. Both units are getting power (red LED at the rear and green LED at the front). However, absolutely nothing comes out of either speaker. Even if I disconnect the Jack from the rear there is no crackling ar anything. I am using audio inputs (1/4" jacks), and I have the slide switch set to audio (as opposed to digital). Am I being comletely dumb and failing to do something, or do these units have known faults?

     

    Thanks in advance.

    read more...
    0 18
    • Jonno
      NicJonesMT Hi Jonno,
      Can you let me know your full setup if possible, including all connected devices and how you have your system connected.
      • August 14, 2020
    • Jonno
      Jonno Hi Nic. At present I don't really have a setup as I have just bought the monitors and have only just started to put together a home studio. I was simply using my iPhone with a splitter cable to split the stereo 3.5mm audio jack output of the phone to two mono 6.35mm jack plugs.
      • August 14, 2020
  • New
    kentbyerly1
    Newcomer - Level 1
    2020-12-03

    Does anybody know if recone kits are available for the Tannoy system 10 DMT II studio monitor.

    Thanks

    0 61
    • kentbyerly1
      john0121 Hi Kent, you can submit a spares parts inquiry via the support button at the top of the page, a member of the team will then be able to provide you with pricing and availability.
      • December 3, 2020
    • kentbyerly1
      Tgregorek I got the last 2 diaphragms on the planet.
      • December 4, 2020
Go to page