Statistics

216,310 members
89,519 posts
  • callanberry
    Contributor - Level 1
    2020-04-04

    speaker no longer powering up.  lim led flashes briefly when powered on

    0 69
    • callanberry
      RexBeckett

      @callanberry 


      Hello Callan, welcome to the community.


       


      I suggest that you raise a Care ticket for Service Repair explaining your problem. This is done by clicking on Support at the top of the page and then clicking the Create a Care Ticket button. This is only possible if you have completed all the required fields in your profile. Make sure that you fill-in every required field on the Care form.

      • April 4, 2020
  • New
    singaporerock
    Newcomer - Level 1
    2020-12-11

    Hello,

    i submitted a request for spare parts and schematic for ip3000 oct17th and still havent heard a peep

    could you please provide part numbers and quote for

     

    2 low frequency drivers

    2 midrange drivers

    power amplifier board

    the clip/wiring harness that goes on the top of the subwoofer that connects into the tower of speakers

     

     

    Case Number CAS-148542-Y5B8L6 .

    read more...
    0 25
    • singaporerock
      ChrisEdwards1 Hi Robert, I am sorry to hear you have not yet had a response to your inquiry. Our spears team is currently experiencing a higher than average case load at the moment, however, I will make them aware of the situation and they will endeavor to reach out as soon as possible.
      • December 13, 2020
  • Ultradj
    Contributor - Level 1
    2020-02-03
  • gm12338
    Contributor - Level 1
    2019-10-12

    I sent back a Samson VX8.1 line array pa unit that was not working properly and decided instead to buy a Turbosound IP1000 which I rec'd 10/12/2019.  I only ran the IP1000 a few hours to practice on my Roland RD-2000. The rear metal plate where inputs plug in, gets almost too hot to touch.  Should I be concerned about internal heat build up as I don't see a visible cooling fan nor any air vent ports.  On the Samson VX8.1 I returned, plus many other models I've researched, do have a visible cooling fan and or air venting with some having possible non-visible internal fans. On this blog somewhere, I read someone was asking IF there was an effective way to retrofit a cooling fan solution for their speaker.  I do "know" that excessive heat does in fact break down electronics over time.  IS there any internal fan or any air porting/venting in any of the Turbosound Inspire IP1000 thru IP3000 models? I like the sound I'm hearing, I'm also thinking about pa system longevity too.

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

    read more...
    0 95
  • Djchillb
    Contributor - Level 1
    2019-10-02

    Hello, 

    I will be attending the bpm trade show this weekend in Birmingham and o note that you will also be attending, I did enquire last year about the ip300 but you hadn't brought 1 with you

    if poss can I ask that you take 1 this year so I can have a look / listen as very interested in a pair

     thanks Ryan

    read more...
    0 70
  • Farsetbelfast
    Contributor - Level 1
    2020-03-10

    Hi guys I'm looking for processor settings for turbosound tq315.

    If it helps I'll be running them passively using a turbosound lms d24 processor. 

    0 60
  • JasonGibson
    Contributor - Level 1
    2020-02-13

    Hi all.  Am a new owner of a IP300.  I plan to get another, plus one or two subs, and am looking at different online purchase options.  Are the European models of Turbosound speakers identical to North American models, apart from the fuse?  i.e., if I bought a European model of the IP300, could I make it North America "ready" simply by changing the T 3.15 A H 250 V fuse to the T 6.3 A H 250 V?  

    read more...
    0 74
  • mmccutchen
    Newcomer - Level 1
    2020-06-21
    I have two IP2000 speakers and one works fine but the other has very little volume and sound seems to break easily. Looking for advice since I have little knowledge about speakers.
    0 79
    • mmccutchen
      GaryHiggins Hi, the only advice to start anyway is duplicate every setting from the working one to the faulty one, if no improvement, you may need to put in a CARE ticket to have it repaired.
      • June 21, 2020
    • mmccutchen
      GaryHiggins The gain settings need to be equal, dsp etc. Easy to skip one by mistake.
      • June 21, 2020
    • mmccutchen
      AlexLane Try Performing a factory reset;

      Hold down the encoder Knob and Setup button while powering on the unit, follow all the on screen test instructions.
      • June 23, 2020
  • JasonChambers
    Contributor - Level 2
    2019-05-20

    I have 2 IQ15's that are less than a year old and really haven't had much use.

    At Saturday's show one of them after being powered on for about 3 minute and without any load shows "over temp" on the display and stops audio output.

     

    Contacted the point of sale and it's a 4-6 week turnaround for repair, which is very disappointing indeed.

     

    Anyone else had this issue?

    read more...
    0 185
  • guitarman_nebr
    Contributor - Level 1
    2019-06-26

    Hey all,

    I have been using the IP2000's for a few months now.   They sound great....until I have to push them for a bit more volume.  I have a small band with pre recorded tracks for Bass and Drums...we sing and play guitar over these tracks.

    I seems there is a general agreement to set everything on the speakers DSP to "0" to use these as a PA speaker with a mixer.   However, it seems there is not a clear explaination as to how much input to use to optimize the output of the speaker.  

    The ouput runs hot and pegs out very quickly...to the point the system will cut out or clip.  I think Turbosound should do a video addressing input and output settings.  On the DSP display it will show the input at two bars and the output quickly goes off the scale.   It is hard to balance these two settings.  

    Does anyone have their own experiences to share?

    read more...
    0 249
Go to page