• New
    DarrellTee
    Newcomer - Level 1
    2020-11-27

    Doing some open baffle deigns and need a pair of VX12 drivers with crossovers

    0 136
  • New
    laer
    Newcomer - Level 1
    2021-02-13

    Hey,

    Does anyone know og the spare parts facility is open now, or if it is closed because of covid?  

    0 77
    • laer
      RexBeckett Hi laer, I believe that the parts team are still working. You can request parts by opening a Care ticket.

      At the top of this page, click Support then scroll down the new page and select Parts. Make sure that you enter all required (*) data before clicking Submit. The Care team will respond by email.
      • Feb 13
  • New
    Miche
    Newcomer - Level 1
    2021-02-15

    Hello, i would like if somebody say, where i can buy a only speaker remplacement Tannoy

    read more...
    0 77
    • Miche
      ChrisEdwards1 Hi Miche, If you have not yet done so I would recommend submitting a parts request, this can be done by going to support at the top of the page and filling in the parts form.
      • Feb 14
  • New
    mikeandrade
    Newcomer - Level 1
    2021-03-16

    Hi, I just wanted to know what the typical wait time is to get a response, after creating a case number for a replacement part?

    0 76
  • LP8400
    Newcomer - Level 1
    2020-06-23
    I m looking for the screws to assemble the low feet (or you can also use them for hanging speakers on the walls). I need two complete sets (to assemble the speaker in the holder, to attach the bottom rubber foot, and to install the safeguard mesh in front of the speaker). If someone has an alternative, let me know pls.
    read more...
    0 114
    • LP8400
      AlexLane Hi there! Could you please put in a support ticket to contact our parts team, they should be able to help!
      • June 23, 2020
  • Skirabbit
    Newcomer - Level 1
    2020-07-07
    Hi I have a very old set of these speakers - seems one of the crossover units is not working - can I replace them? Is it worth it? Can I use a more modern replacement with RCA plugs? I assume I should replace both if a more modern version is available. Thanks for the advice.
    read more...
    1 96
  • New
    Ionderla1n
    Newcomer - Level 1
    2021-10-06

    Hi, while i was applying wax on the cabinets i have accidentally spread some of it on the driver cone near the edge resulting a stain aprox. 2sq/cm in size.
    Is there a way to clean it or remove it without damaging the cone?
    Thank you in advance.

     
    read more...
    0 6
  • New
    Chrisatsparq
    Newcomer - Level 1
    2020-11-17

    Hello Am looking to buy replacement drivers for VX12`s Any help would be great Need 4 as it stands

     

    thank you

    0 54
  • New
    LtAmoc
    Newcomer - Level 1
    2021-06-25

    Looking for a replacement fuse, part # T93-00001-45092

    Used in a Tannoy speaker.  As seen in bottom, left of attached photo.

    Cost, shipping??

    Thanks !!!

    0 56
    • LtAmoc
      Dale_M Hi there please go to the support tab at the top and raise a Spares ticket so the team can advise you of price and availability.
      • Jun 24
  • New
    Samuel3000
    Newcomer - Level 1
    2021-11-16

    Hello, 

    I am hoping that I may be able to get some information or help with a project I am working on. I am wanting to build a set of cornetta cabinets for my 10" gold drivers. They are currently housed in the original 3lz cabinets, however there is literally no information or sources for different design cabinets for these drivers.

    I was hoping that I could contact tannoy directly via email to someone who may be able to share archive information, but this seems the only route! 

    I believe that larger, ported or folded horn, cabinets will benefit these drivers and I would like to use a design that has been tried and tested. Hence I would love to bring a set of cornettas to life.

    These will eventually be used as part of an audiophile Soundsystem in a small public listening space, so to have something extra special is needed. 

    Crossovers will be designed and built to suit the design. 

    Any information or archive plans showing the internal details and spec of the original cornettas would be very much appreciated. 

    Or if it would be possible to continue this discussion via email with someone at tannoy who may be able to help? I can explain in further detail the plans for what is being put together and the space these will be used in and how they will be used. 

    The rest of the system will also include sets of hpd 385 drivers, so vintage tannoy will be in heavy use!

    Thank you very much

     

    Sam

    read more...
    0 2
Go to page