Hi,  has any one experiecned this?  Using my Crave in Ableton and when I connect it via usb and hit a key, either on the Crave itself or using my launchkey mini, I get a squealing feedback type sound almost immediatly after the note.  I have to then switch the Crave off and on again to get rid of this insane noise.   This doesnt happen when I go via the midi in, which is ovioulsy what I will do from now on.  So it's usable but confusing and annoying!  Any ideas?

Thanks

Hi! Can anyone advise? My TD3 resonance knob needs replacing, it's out of warranty.

Does anybody know what part nunber it is, or where i can find it? The potentiometer

When turning quickly, it makes a loud crackling sound. Less bad if turned very slowly. A spray of contact cleaner helps fix the problem for about 15 minutes, then the crackle returns. 

Thanks in advance!

I just bought a td-3 and have spent the last 5 hrs trying to get it to recognize midi via 5 pin din. I have ableton, and don't have any issues using it with the td-3. I have a model cycles as well and the td-3 syncs nicely using the "trig" clock input from the model cycles midi out but will not recognize the 5 pin midi in from the model cycles. I have tried changing every midi setting in the model cycles to send midi. I have changed the the clock input to receive midi on the td-3 and tried using both the same midi channel and different ones on the td-3. It will not recognize midi 5 pin din either from my audio interface via ableton, or via the model cycles. What am I missing, or do I have a defective Td-3?

Hi All,

I have recentley pruchsed a TD3 but cann ot seem to get it come through Logic Pro.

I am using Komplete Audio 6 & have the TD3 plugged in via USB & the going from the out port on the TD3  with a TRS cable & then into input 3 on Audio 6.

When i open a software instrument on Logic it plays the pattern from the TD3 on that track but i cannot get the TD3 to play on its own track.

Any help would be much appreciated.

Gary

Any idea exactly what I need to do in order to set these up ? 

been trying for a week now and it's still not working properly. 

the force should usually sync midi devises but it's only synced with the sequencer and not the oscillation or the envelope. 

I'm a newbie to setting up midi equipment. M

 thanks 

Hi there-

I'm attempting to use a bass plugged directly through my Behringer UMC204HD into my laptop (W10 PC). However, I'm not getting any indication of input signal on the UMC device (no green light on 'SIG'). I've also tried plugging into channel 2 with the same result hooking up a condenser mic on both channels with no apparent signal either. I also connected the hardware to a powered USB port, but still no luck. I also have a Behringer UMC404HD, and that is producing the same results. I was wondering if signal was still passing, and attempted to record in my DAW (Studio One), but no signal was recorded. I can confirm that the PC sees the device(s).

Setup for instrument: Bass-1/4" cable to Input 1/2, INST pressed in, tried both pressed in/out for Pad, Gain between 50-100% (I've tried using my guitars, as well as multiple cables too)

Setup for mic: Mic-XLR to Input 1/2, Pad pressed/depressed, Phantom power on, Gain between 50-100%

Drivers have been installed from Behringer's website.

I rarely use the UMC device, and have only plugged it in a few times over the past few days repeating the steps I described above. When I've used it on a mac, it works perfectly. Any thoughts on what might be going on and how I might troubleshoot further? Thanks in advance.

Hi everyone!

New member here. I just purchased my U-Phoria and excited to put it to good use. Unfortunately my Macbook doesn't seem to recognize it. I looked for drivers on the Behringer website but only found drivers for Windows. Can you help me find drivers for Mac?

Thanks so much!