Statistics

305,220 members
189,494 posts
  • New
    acknapp
    Newcomer - Level 1
    2022-10-23

    We have an X32 at my church that we use for in-house sound. It has a Dante card in it which we use to feed (through the network) a ProTools DAW in a separate room for our live stream feed. I would like to know if there would be a way to network a second X32 (in place of the DAW) so that the person doing the sound for live streaming would have the same environment as the person doing the in-house sound.

    read more...
    0 12
    • acknapp
      GaryHiggins It would work just fine IF the second X32 also had a Dante Card installed. One simple managed network switch. Should not have to replace anything (still use Pro Tools) once set up properly.
      • Oct 24
  • New
    DJuanamm2021
    Newcomer - Level 1
    2021-12-16
     
    I have an online radio and I use a Xenyx FX1002 mixer with a small UCA202 audio interface (it has +12 years of use).
    
    I don't use the interface to record, the function it fulfills is the normal one (ADC-DAC).
    
    I want to buy another for the same purpose, which one do you recommend?
    read more...
    0 13
  • New
    Dqninja25
    Newcomer - Level 1
    2022-10-09

    Hey all!

    I have a x32 and have been running it to logic to get a full mix for livestream sound. I just purchased an s32 this week and when I route it all to the board it works great but none of my signals are being sent to logic. Is there a setting I don't know about or is this a limitation of the s32?

    read more...
    0 7
  • New
    CalebYeo
    Newcomer - Level 1
    2022-03-08

    I've bought a new UCA222 USB Audio Interface to connect the PA system (with Mixer Line-Out) to the computer (USB Line-In) for the purpose of public event.   The audio cables are connected following exactly the application diagram provided in the user manual of UCA222 (page 8).  

    Now, due to the need to give a video music presentation (pre-recorded by the computer) during the public event, I intend to use an additional audio cable to connect the audio output of the computer to the audio input of the Mixer, so that all who are present in the public event could hear the music presentation clearly from the PA system.  At the same time, the video will be shown by the computer through the projector for all to watch.  The whole event will be also shown online through ZOOM by the same computer.

    However, would this additional audio cable connection (as shown in red in the diagram attached) cause the feedback or a loopback problem?

    If it does, how do I resolve this feedback problem?

    Thank you for your kind help.


    View Attachment
    read more...
    0 41
    • CalebYeo
      NicJonesMT Hi CalebYeo.
      It is all dependent on what Mixer you are using.
      You would want to remove the output of your UCA from the signal being sent back to the UCA.
      So for example you could send all of the audio that you need for the UCA222 out of a Mixbus, then have the return from the UCA muted to this bus.

      If you could confirm what mixer you are using I can then advise you futher.
      • Mar 9
      • UCA222 to Computer to Mixer to UCA222 causing feedback & loopback problem
        CalebYeo Hi NicJonesMT, or any kind person in the Musictribe community, I need your kind help to resolve the loopback problem. The Mixer I'm using is Martin Roland MT80. As shown in attached file, there is a "Phone" output with knob control for SEND / REPEAT / DELAY / Phone Level, which I supposed is a AUX SEND audio output (analog). However, I can't find AUX RETURN input (analog) on the Mixer. I need to connect the Mixer output to the Computer via UCA222, and then connect the Computer audio output back to the Mixer input. I wonder if I could connect the Mixer Phone analog output (SEND) to UCA222, then connect UCA222 (USB digital output) to Computer, finally connect Computer's analog audio output (line-out 3.5mm port) back to the Mixer Line-In input? If not, how to avoid audio loopback problem? Thanks
        • Apr 6
    • CalebYeo
      CalebYeo Thanks NicJonesMT for your response. I've tried to show you my intended setup configuration in a diagram (attached here) and the info of the Mixer etc, so that you could identify any mistake and to help me to configure a correct setup to avoid the feedback problem. Thanks

      Computer & PA & AV & ZOOM Setup Diagram.pdf
      • Mar 9
  • New
    omarnft
    Newcomer - Level 1
    2021-07-18

    We bought from your compagny this divise ULTRA ZONE ZMX2600  unfortunately last day it was stopped no output program was radiated  when i reach the transmitter site i found the said product off  i tested it it sglow for 2mn after that is shutdown please advise what we can do i trace the fault ifound that the -15v is not fixed and going to zero  we remove the connections inside the problem remain the problem ia the frontal board 

    read more...
    0 47
    • omarnft
      NicJonesMT Please click submit at the top of the page and submit a Service request case and the team will be able to advise you further.
      Just to make you aware, we do not provide any information or support for self service repairs and are not liable for any damage or injury that may occur as a result.
      • July 18, 2021
    • omarnft
      omarnft i did not found the submit
      • July 19, 2021