Statistics

229,108 members
104,083 posts
  • New
    Klark Teknik
    Triber Moderator
    2021-04-15

    DN200
    bit.ly/Klark-Teknik-DN200

    Learn More: https://www.youtube.com/watch?v=wPRcsdrHZu4

    Features dual parallel-connected combo XLR’s / ¼" TRS inputs. When connecting to the Combo XLR input, the input impedance is 20 kΩ, ideal for line level equipment and offering even lower noise performance. It's also equipped with a Stereo input mini jack which is ideal for connecting MP3 players or mobiles phones etc.

    List Price: $129

    #KlarkTeknik #DN200 #DIBox #Active #2Channel

    read more...
    0 23
  • jgomer2001
    Newcomer - Level 1
    2020-07-15
    Hi, In the stereo Klark Teknik DI 10P every input channel has an attenuation knob. Product documentation mentions that knobs at fully clockwise position means no attenuation. What's the max attenuation achievable (ie. set fully counter clockwise) in dBV ? Thanks in advance.
    read more...
    0 71
    • jgomer2001
      jgomer2001 The level knobs of the DI 10P are relative to the signals input into the device. You can relate the 0 to 10 scale to 0% to 100%. So, it will take the signal and attenuate it down the percentage amount you choose of the signal coming in.
      • July 16, 2020
    • jgomer2001
      jgomer2001 Reply received from Customer Quality Support Specialist
      • July 16, 2020
  • jgomer2001
    Newcomer - Level 1
    2020-07-15
    Hi, The stereo Klark Teknik DI 10P features one L+R RCA and one 3.5mm (stereo) inputs. Can all inputs be simultaneously used so the 4 channels are summed to build a single mono signal ? I'm hesitant to try it. I wouldn't like to damage the DI. Thanks in advance.
    read more...
    0 38
    • jgomer2001
      RexBeckett As I understand it, the RCA and 3.5mm sockets are connected directly together. This would not be a good way to sum two stereo sources but it is more likely to damage the sources than the DI 10P. You would get much better results by using a small stereo mixer to sum the sources.
      • July 15, 2020
    • jgomer2001
      jgomer2001 For those interested, here is the reply received by the support specialist: "You could use all inputs at the same time but I wouldn't recommend it to prevent overdriving the passive circuitry. Instead, If you need to use more than one source, plug your sources into a small mixer. Take the mixer's outputs and connect them to one of the stereo inputs of the DI. This will also allow for better control of your individual sources."
      • July 17, 2020
  • AWhite
    Contributor - Level 2
    2019-11-24

    I want to run 8 channels out from ableton, using the DN9630, through aes50 into my x32, and routed to my aux ins 1-8. Can that be done with this device, and how to I set up the routing with this? 

    1 320
    • AWhite
      DaveMorrison

      Hi @AWhite 


      To send 8 channels of 48k audio from Ableton to the X32, send the channels you want from Ableton on separate USB channels (eg. 1-8). Assuming you send USB 1-8, you'll want to assign AES50 (A or B) channels 1-8 to eight input channels. This would be the routing: Routing:Inputs: Channels. For example, you could put those 8 channels on X32 channels 25-32.Screen Shot 2019-11-24 at 5.50.28 PM.png


      Of course, you could alternately put them on 1-8, 9-16, or 17-24.  The DN9630 will sync to the X32 through AES50 and Ableton will sync to the DN9630.

      • November 24, 2019
    • AWhite
      AWhite

      Is there an option to route them to 33-40 (aux ins) Maybe that's what you are showing in the image, but would I thin loose 8 ins on the 1-32?

      • November 24, 2019
    • AWhite
      DaveMorrison

      @AWhite 


      You can remap those the Aux inputs but Aux In remap is limited to 6 channels. That's why I didn't mention it.

      • November 24, 2019
  • New
    Aldersyde
    Newcomer - Level 1
    2021-04-09

    Does the Klark Teknik DI-10 have a buffer that feeds to the through put?

    0 26
    • Aldersyde
      DavidKnighton Hello Aldersyde,
      The DI 10A specifically does not have a buffered through. It is tied parallel to the input.
      • Apr 9
  • PieterLauwers
    Contributor - Level 2
    2019-11-30

    My hurdy gurdy has four magnetic pickups and a xlr connector per pickup.

    For the moment I play through a Behringer XR18, without any preamp.

    It works, but the gain has to be rather high. Using external effects this results in noise.

    Can I use something like the Klark Teknik CM- 2 as preamp to boost the signal before entering the mixer.

    Any other suggestion is welcome, I am a bit of a dummy concerning sound technique.

     

    thanks,

     

    Pieter

    read more...
    0 366
    • PieterLauwers
      DaveMorrison

      @PieterLauwers 


      Maybe. It depends on your setup. Where are you using external effect and what effects are they? The XR18 already has very good preamps. I suspect your are using effects before the the mixer and the type of effect and it's input and output requirements maybe the source of your problem.


      With a little more information, we can give you some advice.

      • November 30, 2019
    • PieterLauwers
      PieterLauwers

      Example:


      - used effect: EHX Big Muff


      - routing: instrument in, routed to aux, aux in effect, effect out plugged in mixer.


      So, since the effect is plugged in after the input, the problem is with the effect ( tried Boss Overdrive also) or with the gain settings.


      ( I definitely play a lot better then I am in setting the electronics up!)

      • November 30, 2019
    • PieterLauwers
      DaveMorrison

      @PieterLauwers 


      The way you have it setup makes sense for your apllication. The problem is a level and impedance mismatch between the mixer's line level output and the pedal's guitar level input.


      Even if you can get the level low enough, the impedance mismatch will mess with your tone. An line level to guitar level converter (also known as  re-amp) will solve that problem.


      Have you tried the mixer's built in Guitar Amp simulator and Tube Stage emulator. You can insert them in a (pair of) channel(s) to get very good amp simulation. Give it a try and see if you like it, or get a re-amp box.

      • November 30, 2019
    • PieterLauwers
      PieterLauwers

      I use the Tube Stage emulator as an effect on both melody strings.


      so, probably, I will need a reamp box.


      If I understand it right:


      - the effects I use are guitar effects, build for guitar impedance, not mixer line impedance


      - in order to fix noise problems with my outside effect string the mixer's line impedance has to be tempered, ergo the ReAmp.


      Did I say that right? (Still trying to understand the mystic ways of a mixer)


      Thanks!

      • November 30, 2019
    • PieterLauwers
      DaveMorrison

      @PieterLauwers 


      Impedance and really hot levels are the problems. The Radial ProRMP would be a very solid interface, It's got a sweet little transformer that will make your pedals happy. The are many other fine brands of course.


      As a bonus: After you record your parts, you can use your re-amp to manipulate your tracks after they are recorded,

      • November 30, 2019
  • New
    Klark Teknik
    Triber Moderator
    2021-04-13
    DN100
    bit.ly/Klark-Teknik-DN100 

    Learn More: https://www.youtube.com/watch?v=-XH1EsD2ARU&t=3s
     
    An established favourite amongst both engineers and musicians alike. Intended for professional applications where +48 V phantom power is a standard feature on all mixing consoles, and its innovative design results in a significantly higher clipping point than many other active DI Boxes, providing +10 dBu output into a 2 kΩ load.

    List Price: $59
     
    #KlarkTeknik #DN100 #DIBox #Active
    read more...
    1 28
  • gtcode
    Contributor - Level 2
    2019-07-17
    Hi, the DN9630 is an AES50 <-> USB interface and this is the closest forum I could find. Does this device really only support 48k and 96k? Doesn't support 44.1 nor 88.2?
    0 484
    • gtcode
      gtcode Answering my own question here - no, it does not support 44.1 -- only 48/96
      • July 17, 2019
    • gtcode
      ChaseMcKnight

      Hi @gtcode 


      Yes, only 96kHz / 48 kHz. The idea behind the DN9630 was to be a lower-cost recording/playback option mainly geared towards our Midas PRO Series users. Prior to the DN9630, users would need to incorportate a Klark Teknik DN9650 w/ Dante or KT-USB card options (or third-party RPM Dynamics interfaces), which are quite expensive if you're simply looking to track shows or use for virtual sound check. 

      The 48kHz option further add to the market for our M/X32 users -- as most people are using the 48kHz sample rate. Further, many of our 'Blue' DL15x, DL25x, DL231 Stageboxes only operate at 96/48 kHz so this is in line with those product ranges. 

      • July 19, 2019
    • gtcode
      gtcode Thanks for your honesty here, However, in responding, you've implied that "it would cost too much to support 44.1k" and "(basically) nobody uses it anyway". Yet, the M32 supports 44.1k, and people do use 44.1k. The DN9630 should have been designed accordingly.
      • July 19, 2019
    • gtcode
      ChaseMcKnight

      Hi @gtcode 

      Apologies, it really wasn't meant to be implied that way. Nearly all AES50 peripherals relating to PRO Series only 96kHz and 48kHz, such as the DN9680, DN9650, DN9620, DN9610, All 'Blue' I/O boxes, and lastly the DN9630. For M/X32 users, I think the majority of applications where a DN9630 would be used would be in the DN32-USB card is replaced with somethng like the DN32-DANTE card -- and typically users set the sample rate to 48kHz. 

      Although it sounds like you were looking for a 44.1kHz solution and in that case, I understand your frustration. 

      • July 19, 2019
    • gtcode
      Dale_M We have an article on this as it gets asked from time to time, https://musictribecommunity.powerappsportals.com/en-us/knowledgebase/article/KA-01573
      • June 24, 2020