293,992 members
177,049 posts
  • New
    Newcomer - Level 1

    I try to customize the toneprint templates for the hypergravity mini.

    I cannot find any up to date documentation of the editor for iPad.

    I also would like to read detailed information about all the compressor parameters and how they interact with each other. I also cannot find documentation about this.

    Without proper documentation it is a trial-and-error struggle to tweak the templates.

    Can someone provide proper up to date documentation?



    0 11
  • New
    Newcomer - Level 1

    Hi there, desperately trying to find someone in Germany who can or/and is willing to deliver the rotary/push-Enter- Button on the right of the unit. I probably have to replace the whole switch/rotary knob. 
    thx so far

    0 10
  • Rafa78
    Newcomer - Level 1

    Hello, how can I update the firmware of the wizard series finalizer plus.

    0 168
  • New
    Contributor - Level 2



    I have a KT-2a and am wondering what the small Stereo Link trim pot does? I am mainly using the KT-2a for tracking and am wondering what it should be set to?



    0 179
    • RichardPenrose
      KyleJohnson Hi Richard, Kyle here with Music Tribe. The 2A-KT units can be Stereo linked via a TRS cable so that you can use a pair of them. The Trim is there so that if you see inconsistencies on the gain reduction meters between the 2 units you can correct them with the Trim.
      • November 13, 2020
    • RichardPenrose
      RichardPenrose Hi Kyle. Thanks for the info. Where should the stereo link trim be set when using a single KT-2a for tracking?
      • November 14, 2020
      • Klark Teknik KT-2a - Stereo link trim?
        KyleJohnson Thank you for your patience. Keep it at the Default/0 setting when using a single unit.
        • November 16, 2020
  • New
    Newcomer - Level 1

    Trying to wrap my head around how to use the compressor section on the DCX2496. I understand it's intended to be used for ducking & de-essing. But has anyone figured out how to use it as an overall "mix-bus" so to speak? If I left the EQ flat and engaged the compressor, would that work?

    0 135
    • ZachMalinowski
      DavidKnighton Hello Zach,
      are you asking how to use compression in general or how best to use it with the actual product? Compression is generally used to the audio peaks down while lifting the soft audio. Ducking is a type of compression that pulls the audio down when another source is playing. Example, a bingo hall wants to play music, but they also need to announce. The announce mic will trigger the ducker to lower the music so the announce is more prevalent in the mix. If you want to just use a compressed audio, then it's possible to do so, just don't engage any of the other elements, such as EQ, Crossover functions, etc.
      • February 12, 2021
      • Compressor Section on DCX2496
        ZachMalinowski Sorry I'm just getting back. I understand how Dynamic EQ works. I just want to use this function as a compressor. I've attached photos on how 's currently set up--- Basically have a low shelf that I pulled to to -7dB. Then I have the threshold at -15dB, ration at 6:1. In theory, since I didn't pick out specific frequency bands, It technically should act as a basic compressor, yes? I am using the limiters, but I wanted some compression to glue the low end together, and didn't want the limiters to have to brick-wall everything.
        • February 25, 2021
  • New
    Newcomer - Level 1

    Hi KT team, I've followed a previous post from before Xmas and contacted suppliers re availability of a pair of 2As in a bundle I need.

    Thomann replied with "sold out and not expecting any more". Please can you advise if 2A has been discontinued, I'm ready to order a pair of 2As, a pair of 76s and a dimension.


    0 165
    • AudioForge
      PedroRodrigues Hi Audioforge, please be aware that I can confirm that the units are not discontinued, in regard of availability I would advise you to contact another reseller to request that information about these product as we do not have access to information of third party company that distribute our products. Thank you
      • January 14, 2021
      • KT2A / 2AKT
        AudioForge Great news, thank you
        • 1
        • ·
        • January 14, 2021
  • New
    Newcomer - Level 1

    Last year I bought a Shark FBQ100 from my local vendor. Estimated delivery time were January this year. When January came, the delivery date got moved to April. The month came and went without and update.

    I contacted the vendor this month, and the response was that it isn't on stock in China. Other vendors abroad have either removed it from their sites or has delivery dates many months into the future. No specifics were available regarding production status.

    So, I try to seek an answer, hopefully from a more direct source.

    Has this become a discontinued product? Any status regarding production?

    Some clarification would be appreciated.

    I apologize, had trouble finding an e-mail to contact, or an appropriate channel to direct this question.

    0 76
    • samaron
      Paul_Vannatto Good chance that they have been held up due to the chip shortage, like many other electronic devices and automotive vehicles.
      • May 18, 2021
  • New
    Newcomer - Level 1

    Hi folks.

    Is the KT-2A going to be available again? I'm keen to have one, but if not I will look at other options. Thanks.

    0 90
    • willowsam1
      john0121 Unfortunately as we do not directly sell products to end users we are unable to provide any information on pricing and availability of products. You will need to instead directly contact one of our resellers/partners and they will be able to advise you further. You can find the details of our international retailers/partners at the following link:
      • November 1, 2020
  • New
    Newcomer - Level 1

    I was recently made aware of the bypass on the 76-KT, and was wondering if the KA-2A has an option?


    0 147
  • New
    Contributor - Level 1

    The LED light on my pedal won't turn green when I hold the button down and inserting the power supply.

    0 4
Go to page