Hi, I would like to connect "Presonus eris 3.5" to "Behringer um2" using balanced cable, is this the right cable? Or some other cable?
Hi, I want to connect "Behringer um2" to "Presonus eris 3.5" using balanced cable, so the cable on the pic is the right one? Thank you in advance.
The Behringer um2 doesn't have balance outputs so there is no cable to make a balanced connection.
Ohh I see... Thank you for your kind answer, if I may ask? What is the best way to connect Presonus eris 3.5 to my laptop? Should I look for a DAC with balanced output or go for Behringer um2 or just use the headphone jack and don't bother at all?
How about an RCA (normal Hi-Fi stereo) cable? That's the easiest.
I have the X32 Rack in use with the firmware version 3.11. Now I found the firmware version 3.12 for X32, dated with November, 8th 2019. The firmware 3.12 for X32 Rack is dated with July, 2nd 2018. Is that also the newest firmware, only with the wrong date?
Hi, I need some instruction of how to connect myBehringer UMC204HD to my Yamaha keyboard and to my PC. I need to send a song to my PC and at the same time I need to add a vocal live track.
I am using W10 and also I have Cubase 5 in my PC.
Thx,
Paul
If you want to record the keyboard and microphone at the same time, you'll need to hook the mic to input 1 and the keyboard to input 2 (or vice versa). Set Track 1 in Cubase to input 1 and Track 2 to input 2.
Thank you Dave, but the problem with this setup is that you will hear keyboard from left speaker and vocal from right speaker or vice vesa.
Hi all,
I know this has probably been addressed but I can't find exactly what I'm looking for, so here goes.
M32R set as 32in/32out, DL16 connected. Everything feeds into Logic, I can hear live playing and hear playback of Logic Output (channels 1&2), I have these routed to last bank of inputs on Midas. This is what I need:
1) How can I record into Logic, post fader? I want the EQs, Comp, Gate, effects... ect... OR... Can I monitor with effects from the board while sending clean signal into Logic ?
2) Playback- A) Best solution for multiple musicians hearing a multi-track recording session? DP48?
Any other solutions or help setting up the best routing is much appreciated.
Thanks
@Gletterle wrote:
1) How can I record into Logic, post fader? I want the EQs, Comp, Gate, effects... ect... OR... Can I monitor with effects from the board while sending clean signal into Logic ?
You can do either. Selecting Local in the Routing : Card tab only gives the direct out signal from the preamps. Switching those to a combination of Out 1-16, Ultranet, and Aux In, will enable you to define where the signal is tapped. If you use a mixbus (or two) for monitoring, you can select where in the channel the mixbus taps its signal.
2) Playback- A) Best solution for multiple musicians hearing a multi-track recording session? DP48?
DP48 is a good solution. A lot of people will use pairs of Mixbusses for monitoring in conjunction with a tablet/phone app (MX-q, Mixingstation) for the musicians to build their own mix.
Try using the Ultranet menu/Outputs 1-16 menu for the sources of card out 1-32. Set them up as direct outs of each ch. That way you can choose the tap point for each ch to your daw. Using "local" card outs takes the signal at or just past the preamp, basically flat. You can set the outputs of all the daw ch's to be stereo out 1+2 and use aux remap set for card 1-2. You can then monitor the daw tracks on aux 1 and 2 while hearing your live inputs 1-32 in their normal ch position. For daw playback, that will be the usual card 1-32 for the mixer inputs.
Under Routing : Inputs , you could set the Record button (for basic tracking) to have 32 (or 24) inputs as mic preamps and 0 (or 8) inputs as DAW playback and then set the Play button (for over dubbing) as 8 inputs as mic preamps and 24 inputs as DAW playback. It depends on your desired working style.
Bought this speaker on line thru Guitar Center. Scratch and dent. Can't find receipt. GC was no help. Amplifier quit working. Where should I send ? Just the amp or complete speaker. Will it be backed by warranty?
If you registered your speakers, seems it would be covered. Maybe not for the full 10 years being dent and scratch but it is possible. Either way, you need to create a CARE ticket. While signed in, click the "Support" tab up top of this page and follow the directions.
Would buy the tannoy xt8f but the dealer said it is discontinued. What are the new modell?
I have an original mXC Centre speaker for my cinema room set .18 years old and purée the. So much so I purchased a second hand one for another room set up. But it has a fault sound only comes from the tweeter and nothing from the two other speakers. The cabinate is perfect not been dropped and all connection posts are good. I tested on my original amp then put back my original speaker and that sounds great. So I know it’s not a cable or amp fault. Can anyone help please ideas
cheers
Just joined and so far this sucks. Bought a Behringer mixer after review of add showing software avaliable. Downloaded what I found and got was nothing more than public domain software. Audacity. This is not the software used in the web site demo.
Anyone have a clue whre I can get what was advertisedin web promo?
This really sucks. Software should have come with product. Downloads require too much personal info. I did it and the download is NOT what was shown on demo.
@Ricktek wrote:
Anyone have a clue whre I can get what was advertisedin web promo?
That is an old video actually. The person in that video hasn't been with the company for at least 2 years. Many things have changed since then, including Tracktion (which he mentioned). It is now called Waveform which is available (version 7 is free) here. By the way, even the X32 and new Wing does not come with DAW software. Also, for the record, the Q802USB does not provide true multi-tracking signals. It only has stereo (2 track) bidirectional via USB.
Thanks for reply. Do you know if i can record stereo to pc using USB out on mixer? Would I be able to adjust audio going over USB with mixer or is it fixed at one setting? I am only looking to record a left and right channel.
I've had a pair of Churchills (043A and 043B) for almost 20 years and have misplaced the manual. It doesn't show up on the list of downloads. Can anyone help me with a PDF copy? Thanks.
Hi, I've been using an Xr-18 for a few years now and have never had problems with the XAir app, but these days ago I updated IOS to version 13.2.2 and to my surprise was that the app is no longer working as it should. Can anyone help me regarding this? What should I do ? The latest app update is over 2 years old, will anyone solve this?
Hello Adriano, welcome to the forum.
Please see this thread for information about your problem.
Look out for a email with your unique access code and details on how to join.
We look forward to seeing you soon!
Look out for more session announcements soon on our social media channels and at www.musictribe.com
EN
ES
ZH
ID
JA
FR
DE
.
All Categories
Musician
Recording and Streaming
Live and Tour Sound
Install
Gamer
Lifestyle
New
Recently Updated
Popular
Unanswered
Solved
Discussions
Videos
Photos
Files
