Statistics

298,815 members
182,480 posts
  • jasbirnandra
    Contributor - Level 1
    2019-11-26

    I am interested to buy speakers from tannoy as there are no dealers here want to contact them and do not have any contact details can someone share the same, please.

     

    regards

    jasbirnandra

    0 492
  • avfern
    Contributor - Level 1
    2019-07-25

    I wish to develop a home cinema in space of 20 x 30 sq. ft. room size. Apart from professional display, It should have excellent sound system with Dolby effects. Kindly suggest be best configuration of speakers, amplifiers, controls, etc. and their positioning.

    read more...
    0 416
    • avfern
      KenMitchell

      HI Gopel ( @avfern ), 


       


      Welcome to the community.  The first thing you need to tell us is what your approximate budget is?  Also it would help to tell us what part of the world you are in as not all products are offered in all countries. Since you are posting here I'll asuume you'd like to focus on Music Tribe products but that's not really their forte.  I believe most of their products are multi-zone type audio distribution products. 


       


      Hope this helps, 


      Ken

      • July 25, 2019
    • avfern
      zeno86 So you could get UST with an ALR screen and it would look wonderful, but it wouldn't be as good as an oled. However, in my mind, sheer size is more important than perfect blacks for movies in terms of creating a cinematic experience.
      • Mar 30
  • PookalPookum
    Contributor - Level 1
    2019-09-20

    I have a Crown Amp XLS 1002 that are connected to Polk RTI6 passive speakers. I want to also connect my Sub to the amp. I have a Powered sub. I also have a SMSL SU-8 Dac that is connected via the balanced outputs.192.168.0.1

    I done some reading but still dont understand it quite yet. From what I understand and correct me if am wrong.

    From the DAC i need to use a Y XLR cable and connect it to channel 1 input. whatsapp web

    Then I connect the sub channel 2 output via either speakon or binding postsrouterlogin

    Then I connect the passive speakers to channel 2 output(But I would need to bi -wire the speakers in parallel or something like that?)

    Then the Crossover in the AMP directs all the traffic with the pass filters?

     

    If all is correct. How does it determine left and right for imaging? Or do I lose that when I connect it this way?

    read more...
    0 362
  • Analizaplazaro
    Contributor - Level 2
    2020-02-20

    Hi please help how can i connect my mixer to my TV and powered speaker?

    thank you

    0 288
    • Analizaplazaro
      RexBeckett

      @Analizaplazaro 


      Hello Analiza, welcome to the community.


       


      We should be able to help if you tell us the make/model of your mixer, TV and powered speaker.

      • February 20, 2020
    • Analizaplazaro
      Analizaplazaro

      @RexBeckett 


      thanks for your reply..


      tv - philips


      mixer - behringer 1202fx


      powered speaker - rockville bp10


       

      • February 20, 2020
    • Analizaplazaro
      RexBeckett


      @Analizaplazaro wrote:


      @RexBeckett 


      thanks for your reply..


      tv - philips


      mixer - behringer 1202fx


      powered speaker - rockville bp10


       





      @Analizaplazaro 


      You should be able to connect the 1202FX Main outputs to the BP10 channel 1 inputs using TRS/TRS cables like these. Without knowing the model of the TV, it is not possible to say how it could be connected to the mixer. Some TVs have two RCA output connectors for sound. If so, you could use a cable like this to connect to one of the 1202FX stereo inputs (5/6, 7/8, 9/10 or 11/12).

      • February 20, 2020
  • Koufou
    Contributor - Level 1
    2020-03-28

    Bonjourr a tous

    Je possede des dynaudio m3 A pour un usage salon hifi  je  n est pa encore d ampli j aimerai acheter le lab gruppen 1000q   j aimerai savoir les réglages  complet qui ia a faire pour cette enceintes. ia t il un preset dans l amplificateur ?

     Ou quelle autre configuration fonctionnerait 

    MC_2681577446878154376.jpg

     

    Merci d avance

     

    read more...
    0 261
  • Thomasb12321
    Contributor - Level 1
    2019-10-18

    Hi, 

    I am very novice with audio but usually once I can play with things I'm very good at learning. I inherited a DEQ2496 and some other components. But there is no way for me to tell in what order I should hook them up in. For example, the amplifier, receiver, etc. If you could send me what order to hook things up, I'd very much appreciate it. Thanks. 

    Thomas

    read more...
    0 238
  • agaurav009
    Contributor - Level 1
    2019-12-05

    I have made a basic setup using tv audio-aux out for music-source and microphones for vocals. I found music was noisy. So, I did lot of debug and the summary is as below:

    I started using only 1 channel out of 5-10, say M, keeping all other chanels mute i.e. all channels from 1-12 are mute except M. Even then I get quite noisy output on my soundbar. Source of music is youtube karaoke track from TV audio aux-output (of course TV audio is muted). Only weak point in connection I can't debug is the 3.5mm-male to 6mm-male cable or 3.5mm-female to 6mm-male converter. I have checked tv audio out using RCA cables to my soundbar and the music is perfectly alright. So, source is perfectly fine. Assuming the cables are alright (as chances of cable and adapter both being bad are low), its the mixer XR12. I think its my settings (.scn) as microphones sound alright but when music is entered through same mic-channel, noise is there. Any suggestion?

    read more...
    0 232
    • agaurav009
      RexBeckett

      @agaurav009 


      Hello Anand, welcome to the community.


       


      What type of connector is the TV output? If it is a stereo 3.5mm socket, you would need to use a cable like this to separate the two channels and connect the 6.35mm mono plugs to two adjacent channels - e.g. 5 & 6.


       


      If the TV output is RCA sockets, use a cable like this and also connect to two mixer channels.


       


      In both cases you should stereo-link the two channels in your XR12 setup using XAir-Edit.

      • December 5, 2019
  • DaleM
    Contributor - Level 1
    2019-10-03

    Just purchased  a Behringer EP2000.  I would like to power two(2) 10" subwoofer externally from the sub pre out: what needed between the home reciever and the EP2000 to match the impedence?

    0 208
  • danlynch37
    Contributor - Level 1
    2020-04-01
    Hi,
     
    I have tried to raise a support ticket three times tonight and it keeps saying there is an error.
     
    I have a Tannoy TS2.8 Sub (Serial Number 80006580160115806811) which has no sound coming out of it. The led on the back is flashing red and I have tried a different power lead and cable but that has not made a difference. The fuse is OK. It is still in warranty and I have attached proof of purchase. Can you resolve it remotely or will it need to be returned?
     
    Kind regards,
    Danny
     
    read more...
    0 187
  • New
    Fbch
    Newcomer - Level 2
    2021-07-22

    I run the sound at church and know very little about what I am doing. We have had this mixer for about 1.5-2yrs. The issue has been on and off but continues to get worse. The mixer generates its own WiFi that we connect to with an iPad. Very often the iPad will not connect. Sometimes it won't even be able to find the XR WiFi. 

    We have tried a few different troubleshooting ideas and nothing helps. There is nothing else (phone or computer) trying to connect to the WiFi. We have also tried other iPads. What am I doing wrong?

    read more...
    0 185
    • Fbch
      Nigel67 The XR16 internal wifi uses the 2.4GHz frequency which is the most common and it could be that with all the mobile phones around, etc, the frequency is becoming log jammed. Have you tried using an external router which also uses the 5GHz frequency. This also gives the advantage that you can place the router higher up as having the antenna low down will also affect the wifi range. Please see this video that may be helpfiul.
      https://www.youtube.com/watch?v=xLqc_4Q4ERY&list=RD58IfULV5V6E&start_radio=1
      • July 21, 2021
      • Behringer x air 16 not connecting to ipad
        Fbch I will try that this week. I have an Ethernet cable run to the sound board but I do not have a computer over there. So if I connect the mixer to my modem, I can connect to the app via the church WiFi? (Like I said, most of this goes over my head)
        • July 22, 2021
    • Fbch
      Nigel67

      Hi Fbch. many apologies for the delay in getting back to you. For some reason I only received the notification that you had replied this morning. How did you get on connecting to the wifi. I would advise probably using a separate router rather than the church wifi. if you don't move around the church, have you thought about getting an adapter for the ipad so that you can connect it directly to the ethernet port and charge at the same time. You can purchase Lightning to ethernet port adapters which also have a power adapter as well. A long as the ipad isn't moved around a lot for the cable to be pulled out, then this would probably be your most secure connection followed by the external router.

      • July 29, 2021
Go to page