Statistics

267,858 members
147,368 posts
  • AdmiralLemon
    Newcomer - Level 1
    2020-09-17

    I was streaming and heard a slight static type of pop in my right earbuds. I could only hear out of the left side and only static in the right after that. I replaced my earbuds with my ATH-M50x headphones and got the same result. I rebooted the PC but the issue was still present. I then tried unplugging the GoXLR with the headphones still plugged in. When I plugged the GoXLR back in a horrid squealing noise was present in the right headset. I tried other headsets and got the same issue. Mic quality has not changed and everything else with the GoXLR seems normal.

    read more...
    0 1,362
    • AdmiralLemon
      Nigel67 Hi, unfortunately it looks like your GoXLR has developed a fault in the headphone circuitry and needs repairing. Possibly the headphone amp has gone faulty. Please go to the support tab at the top of the page and fill in a support ticket. Assign it as a Service Support ticket when you get the option in the drop down box. One of my colleagues will then be able to get back to you with repair details.
      • September 17, 2020
      • GoXLR Headphone Jack Input Stopped Working?
        AdmiralLemon OK thank you! I was afraid it was something like that. I sent in a service request.
        • 1
        • ·
        • September 18, 2020
  • New
    sanelso2
    Newcomer - Level 1
    2021-05-08

    Hi, I have two questions:

    1) Is there any difference between the TC Helicon Voicelive Play and the Play Acoustic, besides the Play Acoustic having the guitar input (for key detection and efxs) and guitar effects? So does this mean both versions of the units have "exactly" the same vocal effects?

    2) On either unit, cans Voicelive VoiceSupport2 software be used to pre-program the keys of invidual presets that can be then sent to the VLP units? ...or is the VoiceSupport2 software basically for only backing up, copying, and changing order of presets?

    Thanks for you help in advance!

    read more...
    0 1,314
    • sanelso2
      JoeRivers96 Hi, thank you for your contact. The vocal fx on these two units are the same - you will see some different presets on the Play Acoustic due to the guitar input.

      Unfortunately internal settings cannot be edited on VoiceSupport 2. This software is purely for preset management and firmware updates.
      • May 8, 2021
  • lana22
    Contributor - Level 1
    2019-07-08

    I powered down and accidentally powered up a few minutes after... shouldn't have bothered it, but it powered back up with a blue screen. 

    It is version 1.2.00 build 61
    I'm using VoiceTouch on my Mac.

    VoiceTouch says it's being used by another app. I've done everything a person can do on my Mac (privacy settings in Chrome, system preferences...) to make that not the case, to no avail.

    I can't see the screen, so I can't do anything like a factory reset - because I can't tell what's happening.

    I, of course, have a gig tonight.

    Please help me.

     

    read more...
    0 1,281
    • lana22
      BrianLowe


      @lana22 wrote:


      I powered down and accidentally powered up a few minutes after... shouldn't have bothered it, but it powered back up with a blue screen. 

      It is version usps tracking 1.2.00 build 61
      I'm using VoiceTouch on my Mac.


      VoiceTouch says it's being used by  another app. I've done everything a person can do on my Mac (privacy settings in Chrome, system preferences...) to make that not the case, to no avail.


      I can't see the screen, so I can't do anything like a factory reset - because I can't tell what's happening.


      I, of course, have a gig tonight.


      Please help me.


       





      I am also facing the same issue here. Help is highly appreciated.

      Thanks in advance,
      Regards,
      Brian

      • July 8, 2019
    • lana22
      TCH-Spencer

      Hey @lana22 and @BrianLowe,
      Both of you will need to get in contact with our support team via this link.  Good luck!

      • July 9, 2019
    • lana22
      kantefier

      Greetings!


      I'm currently facing the same issue on my unit. Suddenly only blue screen, device doesn't boot up. Downloaded Voicesupport 2, as some older internet posts suggest, but on both operating systems (Win & OSX) I get the same result: "Device in use".


      Also, provided link doesn't work. Please help!

      • January 1, 2020
    • lana22
      TCH-Rob

      Hi @kantefier ,


      You can receive help from the "support" tab on www.musictribe.com


       

      • January 3, 2020
    • lana22
      optpenn

      Greetings!


      This is not good!!! I'm facing the same issue on my unit. I see only a blue screen. I Downloaded Voicesupport 2, as some older internet posts suggested.  I got the same results: "Device in use". 


      Please Help!

      • January 7, 2020
  • s2uunny
    Newcomer - Level 1
    2020-07-10
    download app go xlr version 1.1.0.85 but continue error window pops up "checking for update" and Automatically turns off app
    0 1,195
    • s2uunny
      Dale_M Hi there. Our recent server migration revealed a critical bug that caused the app to crash. We were able to work with the PH team who managed to upload the missing files and redirect the URL path. This fixed the crashing bug for everyone on the latest app, however anyone on an older version will need to update using the below link, or they may still experience the crash.

      Please use this App installer if you are still experiencing crashing:

      http://tc-helicon.com/FirmwareAssets/GOXLR/GoXLR-App-1.2.3.103.zip
      • July 10, 2020
  • JKing
    Newcomer - Level 1
    2020-07-21

    Recently updated my goxlr driver, but now I can't hear any audio from my PC into my headphones, the interface works, both digitally and physically, I can hear my mic inside the goxlr, but any videos, music programs, etc I can't hear in my headphones. What can I do to fix this?

    read more...
    0 1,174
    • JKing
      AlexLane I suspect you just need to select the GoXLR as the active audio device, click on the sound icon in system tray, click on the text above the volume slider and select it.
      • July 22, 2020
  • New
    Mazards
    Newcomer - Level 1
    2020-12-30

    Hey all, so I am using a Blue Yeti X Condenser Microphone and was told that all you need to do to connect it to the GoXLR is just to add the 3.5mm cable to it and done. However, whenever I try to plug it in all I hear is a loud screeching sound and I cannot use the Chat Mic option. If anyone has a solution, I would truly appreciate it! Thank you!

    read more...
    1 1,146
    • Mazards
      PedroRodrigues Hi Osman,please note if you intend to use the popular Blue Yeti microphone, which has its own built-in headphone output, you should run that built-in headphone output into the GO XLR’s MIC input.
      For Blue Yeti mics powered via USB, plug the USB connector directly into your computer for power, but do not select the Blue Yeti as an audio source on the computer.
      Instead, the Blue Yeti’s headphone output will be the audio source for mixing inside GO XLR.
      • January 7, 2021
  • New
    stephensmiles
    Newcomer - Level 2
    2020-11-04

    I'm doing some recording with Ableton.  I'm about to buy a condenser mic, probably a Rode NT1 or Aston Origin. Both require 48v phantom power. Will my Voiceplay live support this or do I need to buy another Audio Interface?

    0 1,015
    • stephensmiles
      stephensmiles Actually I seem to have discovered that it does:-) Next question. Is there a flat (no effects) setting on the Voicelive play?
      • November 4, 2020
      • Voicelive Play Phantom Power
        leah Hello Stephen,
        The VoiceLive Play has a "Talk" mode where you can quickly bypass the effects from the current preset. This is done by holding down the HIT footswitch.
        If you'd like a dedicated preset with zero effects applied, you can either transfer a "Blank Preset" style to your device using VoiceSupport 2 or simply build a new preset with all effects off within the device.
        Hope this helps. Thanks!
        • November 4, 2020
      • Voicelive Play Phantom Power
        stephensmiles Thank you.
        • November 4, 2020
    • stephensmiles
      RexBeckett Hi Stephen, according to the specifications, Voicelive Play has a 48V phantom supply when enabled through the Setup menu.
      • November 4, 2020
  • Dale11
    Contributor - Level 1
    2019-10-09

     I own a perform V  however it does not fit on my microphone stand and it is very difficult to change the effects during a performance.  I am considering purchasing a mic mechanic or a voice live play.  I need something very simple that I don’t really need to change the settings on too much. I sing popular type rock. 

     Can you please make a suggestion for me? I know they perform V has doubling  I don’t see this on the mic mechanic and not really sure if I need it. Mostly I want tone, pitch correction and a little fuller voice with a very small amount of reverb/echo.  I am not a pro so I need something very simple. Please help, thank you 

    read more...
    0 845
    • Dale11
      TCH-Spencer

      Hey @Dale11,
      It sounds to me like the Duplicator is the pedal for you.  It has doubling, reverb, pitch correction, and Tone.


       


      Also in regards to your Perform-V not fitting on your mic stand, please check out David's rant.  You might just need to put some muscle into it, it's very unlikely that you'll be able to break the plastic on the Perform-V's mic clip by forcing it on there.

      • October 11, 2019
    • Dale11
      SteveSchow

      The Duplicator looks pretty darn nice....and SIMPLE...which is good.  I really love my VoiceLive Play a lot though.  I like having presets.  Truthfully I don't end up using much more than what that Duplicator can do, but I have found it beneficial, as a backup singer, to be able to totally disable my mic with a muted preset, for songs I don't sing on, for example.  I don't see how this unit would let you adjust the gating sensitivity, for example, where with the VoiceLivePlay you have more options to configure how all that stuff works. 


       

      • November 5, 2019
  • New
    burkeingraffia
    Newcomer - Level 1
    2021-01-23

    I have a TC Helicon Mic Mechanic 2.  It has always worked well, and this morning I thought I would see if there was a firmware upgrade.

     

    I'm on a Mac (Catalina OS).

     

    I downloaded the VoiceSupport2 app for Mac, and everything seemed OK, at first. My computer recognized the pedal plugged in via USB and said it needed a firmware update.  It started through the process and then it errored out.

     

    I have tried everything from rebooting the Mac (with and without the pedal connected), and nothing works.  The pedal is not even recognized my the Mac in the System Report. The pedal still powers up but does not work at all. 

     

    Is there a way to directly add (or reset the original) firmware without VoiceSupport2?  Is this pedal bricked because the firmware update and VoiceSupport2 will never allow the computer processor inside of the pedal to ever work again? 

     

    Any suggestions would be greatly appreciated.

    read more...
    0 830
    • burkeingraffia
      burkeingraffia Also, the very poor VoiceSupport2 software offers me a link to a page that is no longer there: https://music-group.force.com/musickb/view/article/tch/VoiceSupport-Can-t-connect-update-device-228160107
      • January 23, 2021
    • burkeingraffia
      PedroRodrigues Hi, burkeingraffiaI would suggest performing first a factory reset followed by a firmware update.
      To restoring the factory preset in the Mic Mechanic, first you must downloading the VoiceSupport application. Then simply click the first preset in the list and SHIFT and click the last preset in VoiceSupport, and then press “Apply Changes” to start initialization of the program.
      Warning! This procedure will return all of the settings to the values when the Mic Mechanic was shipped from the factory. Do not use this function unless you are certain that you want to do this. Hopefully the article of “Restore the Mic Mechanic to the Factory Preset” was useful.
      To assist you on the firmware update process please follow the link below and confirm that you are connecting your unit to a USB 2.0 PORT:

      https://www.youtube.com/watch?v=ozHsxKB-0CM
      Thank you
      • January 28, 2021
  • Noamschroeff
    Contributor - Level 1
    2020-03-24

    Does the goxlr mini has a inbuilt amp and dac? I read on twitter that the non mini goxlr has an inbuilt amp that goes up to 150 ohm is that the same case for the goxlr mini? and is the dac inside of the goxlr mini (if it has one) enough to drive my Sennheiser HD 660 S?

     

    read more...
    0 763
Go to page